Ok Yves here is the info you have requested--- I'm not sure why it says
package kernel isn't installed because 2 are installed--- but anyway,
here it is:
[root@localhost root]# rpm -q drakxtools ldetect-lst kernel
drakxtools-1.1.7-71mdk
ldetect-lst-0.1.3-4mdk
package kernel is not installed
[root@localhost root]# ls /dev/usb
dabusb0 dabusb6 dc2xx2 hiddev12 lp0 lp6 mdc8002
scanner11 scanner9 ttyUSB5
dabusb1 dabusb7 dc2xx3 hiddev13 lp1 lp7 mdc8003
scanner12 ttyUSB0 ttyUSB6
dabusb10 dabusb8 dc2xx4 hiddev14 lp10 lp8 mdc8004
scanner13 ttyUSB1 ttyUSB7
dabusb11 dabusb9 dc2xx5 hiddev15 lp11 lp9 mdc8005
scanner14 ttyUSB10 ttyUSB8
dabusb12 dc2xx0 dc2xx6 hiddev2 lp12 mdc8000 mdc8006
scanner15 ttyUSB11 ttyUSB9
dabusb13 dc2xx1 dc2xx7 hiddev3 lp13 mdc8001 mdc8007
scanner2 ttyUSB12
dabusb14 dc2xx10 dc2xx8 hiddev4 lp14 mdc80010 mdc8008
scanner3 ttyUSB13
dabusb15 dc2xx11 dc2xx9 hiddev5 lp15 mdc80011 mdc8009
scanner4 ttyUSB14
dabusb2 dc2xx12 hiddev0 hiddev6 lp2 mdc80012 rio500
scanner5 ttyUSB15
dabusb3 dc2xx13 hiddev1 hiddev7 lp3 mdc80013 scanner0
scanner6 ttyUSB2
dabusb4 dc2xx14 hiddev10 hiddev8 lp4 mdc80014 scanner1
scanner7 ttyUSB3
dabusb5 dc2xx15 hiddev11 hiddev9 lp5 mdc80015 scanner10
scanner8 ttyUSB4
[root@localhost root]# cat /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 11/900 us ( 1%), #Int= 1, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB OHCI Root Hub
S: SerialNumber=c8878000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=03f0 ProdID=0401 Rev= 1.00
S: Product=HP ScanJet 5200C
S: SerialNumber=SG01F170DMHT
C:* #Ifs= 1 Cfg#= 1 Atr=60 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=00(>ifc ) Sub=00 Prot=00 Driver=usbscanner
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 16 Ivl= 0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 1 Ivl=250ms
-Bill
=======
Yves Duret wrote:
>Bill Greenwood <[EMAIL PROTECTED]> writes:
>
>>I have an HP ScanJet 5200C scanner, hooked up to the USB port, and
>>ScannerDrake finds beautifully. ScannerDrake asks me if I want to configure
>>it, and I click on Yes. Hard drive works for a few seconds, then nothing
>>else. (at least it could tell me what happened :) )
>>
>>I then run XSane, and this is the error I get:
>>
>>XSane Scanning for devices
>>
>>XSane: no devices available
>>
>>Several distros back, I would get a link on the desktop when I turned on the
>>scanner. I don't get that anymore.
>>
>
>yes, you should have everything.
>rpm -q drakxtools ldetect-lst kernel
>and with the scanner plug and turned on
>ls /dev/usb
>cat /proc/bus/usb/devices
>thanx
>
