I tried to boot off the CD, hit enter for regular installation, the
progress bar showing the loading moved... till it was 3/4 done, then the
screen went black and the computer was unresponsive ever after that.
The md5sums on the download images were fine, I tried burning the CDs
twice.
Same thing happened when I tried to boot from cd.img or hd.img
I did check the md5 sums of cd.img and hd.img before copying them to a
floppy.
Hardware:
msi k7t266 pro2, bios version 3.4
ati xpert 2000
SIIG controller card
linksys network card
lucent PCI modem
Connected to the motherboard controllers:
wd 440bb
DVD drive
Connected to the SIIG controller card:
IBM hard drive, with zip drive as a slave.
HP CD-Writer 9100
attached: lspci and dmesg when running 8.2
Narfi.
00:00.0 Host bridge: VIA Technologies, Inc. VT8367 [KT266]
Subsystem: VIA Technologies, Inc.: Unknown device 0000
Flags: bus master, medium devsel, latency 8
Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: <available only to root>
00:01.0 PCI bridge: VIA Technologies, Inc. VT8367 [KT266 AGP] (prog-if 00 [Normal
decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00007000-00007fff
Memory behind bridge: dfe00000-dfefffff
Prefetchable memory behind bridge: d7c00000-dfcfffff
Capabilities: <available only to root>
00:06.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366 / HPT370
(rev 01)
Flags: bus master, medium devsel, latency 120, IRQ 10
I/O ports at e000 [size=8]
I/O ports at dc00 [size=4]
I/O ports at d800 [size=256]
Expansion ROM at dffe0000 [disabled] [size=128K]
00:06.1 Unknown mass storage controller: Triones Technologies, Inc. HPT366 / HPT370
(rev 01)
Flags: bus master, medium devsel, latency 120, IRQ 10
I/O ports at ec00 [size=8]
I/O ports at e800 [size=4]
I/O ports at e400 [size=256]
00:07.0 Ethernet controller: Lite-On Communications Inc LNE100TX [Linksys EtherFast
10/100] (rev 25)
Subsystem: Lite-On Communications Inc: Unknown device c001
Flags: bus master, stepping, medium devsel, latency 64, IRQ 5
I/O ports at d400 [size=256]
Memory at dffdff00 (32-bit, non-prefetchable) [size=256]
Expansion ROM at dff80000 [disabled] [size=256K]
Capabilities: <available only to root>
00:08.0 Communication controller: Lucent Microelectronics 56k WinModem (rev 01)
Subsystem: Zoom Telephonics Inc: Unknown device 9300
Flags: bus master, medium devsel, latency 0, IRQ 3
Memory at dffdfe00 (32-bit, non-prefetchable) [size=256]
I/O ports at d000 [size=8]
I/O ports at cc00 [size=256]
Capabilities: <available only to root>
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
Subsystem: VIA Technologies, Inc.: Unknown device 0000
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: <available only to root>
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a
[Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Flags: bus master, medium devsel, latency 32
I/O ports at fc00 [size=16]
Capabilities: <available only to root>
00:11.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Flags: bus master, medium devsel, latency 64, IRQ 3
I/O ports at bc00 [size=32]
Capabilities: <available only to root>
00:11.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Flags: bus master, medium devsel, latency 64, IRQ 3
I/O ports at c000 [size=32]
Capabilities: <available only to root>
00:11.4 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Flags: bus master, medium devsel, latency 64, IRQ 3
I/O ports at c400 [size=32]
Capabilities: <available only to root>
00:11.5 Multimedia audio controller: VIA Technologies, Inc. AC97 Audio Controller (rev
10)
Subsystem: Avance Logic Inc.: Unknown device 4710
Flags: medium devsel, IRQ 5
I/O ports at c800 [size=256]
Capabilities: <available only to root>
01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 RL (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 0008
Flags: bus master, stepping, 66Mhz, medium devsel, latency 64, IRQ 11
Memory at d8000000 (32-bit, prefetchable) [size=64M]
I/O ports at 7800 [size=256]
Memory at dfefc000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at dfec0000 [disabled] [size=128K]
Capabilities: <available only to root>
Linux version 2.4.18-8.1mdk ([EMAIL PROTECTED]) (gcc version 2.96
20000731 (Mandrake Linux 8.2 2.96-0.76mdk)) #1 Mon Jun 24 13:21:53 MDT 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
hm, page 1fff0000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=linux ro root=2101 nobiospnp devfs=mount
hdc=ide-scsi hdb=ide-scsi hde=77545,16,63
ide_setup: hdc=ide-scsi
ide_setup: hdb=ide-scsi
ide_setup: hde=77545,16,63
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 1465.996 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 2922.90 BogoMIPS
Memory: 513416k/524224k available (1171k kernel code, 10420k reserved, 334k data, 264k
init, 0k highmem)
Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU: AMD Athlon(tm) XP 1700+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfdb21, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router default [1106/3074] at 00:11.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Diskquotas version dquot_6.5.0 initialized
devfs: v1.10 (20020120) Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x1
vesafb: framebuffer at 0xd8000000, mapped to 0xe0800000, size 32768k
vesafb: mode is 800x600x16, linelength=1600, pages=33
vesafb: protected mode interface info at c000:4a0b
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture.... found (800x600, 53754 bytes).
Console: switching to colour frame buffer device 80x16
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ
SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
HPT366: IDE controller on PCI bus 00 dev 30
PCI: Enabling device 00:06.0 (0005 -> 0007)
HPT366: chipset revision 1
HPT366: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
HPT366: IDE controller on PCI bus 00 dev 31
HPT366: chipset revision 1
HPT366: not 100% native mode: will probe irqs later
ide1: BM-DMA at 0xe400-0xe407, BIOS settings: hdc:pio, hdd:pio
VP_IDE: IDE controller on PCI bus 00 dev 89
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci00:11.1
ide2: BM-DMA at 0xfc00-0xfc07, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdg:DMA, hdh:pio
hda: IBM-DJNA-371350, ATA DISK drive
hdb: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
hdc: Hewlett-Packard CD-Writer Plus 9100, ATAPI CD/DVD-ROM drive
hde: WDC WD400BB-00AUA1, ATA DISK drive
hdg: TOSHIBA DVD-ROM SD-M1212, ATAPI CD/DVD-ROM drive
ide0 at 0xe000-0xe007,0xdc02 on irq 10
ide1 at 0xec00-0xec07,0xe802 on irq 10
ide2 at 0x1f0-0x1f7,0x3f6 on irq 14
ide3 at 0x170-0x177,0x376 on irq 15
hda: 26520480 sectors (13578 MB) w/1966KiB Cache, CHS=26310/16/63, UDMA(33)
hde: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=77545/16/63, UDMA(33)
hdg: ATAPI 32X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
/dev/ide/host0/bus0/target0/lun0: [PTBL] [1650/255/63] p1 p2 < p5 >
/dev/ide/host2/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 p10 p11 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Uncompressing......done.
Freeing initrd memory: 131k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 264k freed
Real Time Clock Driver v1.10e
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide2(33,1), internal journal
Adding Swap: 255488k swap-space (priority -1)
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: IOMEGA Model: ZIP 100 Rev: 14.A
Type: Direct-Access ANSI SCSI revision: 00
Vendor: HP Model: CD-Writer+ 9100 Rev: 1.0c
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 196608 512-byte hdwr sectors (101 MB)
sda: Write Protect is off
/dev/scsi/host0/bus0/target0/lun0: p4
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide2(33,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide2(33,9), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide2(33,11), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide2(33,8), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide2(33,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide2(33,10), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux Tulip driver version 0.9.15-pre9 (Nov 6, 2001)
eth0: Lite-On PNIC-II rev 37 at 0xd400, 00:A0:CC:E2:3D:B0, IRQ 5.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 13:47:41 Jun 24 2002
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xc400, IRQ 3
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xc000, IRQ 3
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xbc00, IRQ 3
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
parport0: Printer, HEWLETT-PACKARD DESKJET 830C
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack (4095 buckets, 32760 max)
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
parport0: Printer, HEWLETT-PACKARD DESKJET 830C
lp0: using parport0 (polling).
PCI: Setting latency timer of device 00:11.5 to 64
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
Splash status on console 0 changed to off
i2c-core.o: i2c core module version 2.6.2 (20011118)
i2c-viapro.o version 2.6.2 (20011118)
i2c-viapro.o: Found Via VT8233 device
i2c-core.o: adapter SMBus Via Pro adapter at 0400 registered as adapter 0.
i2c-viapro.o: Via Pro SMBus detected and initialized
i2c-proc.o version 2.6.2 (20011118)
adm1021.o version 2.6.2 (20011118)
i2c-core.o: driver ADM1021, MAX1617 sensor driver registered.
w83781d.o version 2.6.2 (20011118)
i2c-core.o: driver W83781D sensor driver registered.
i2c-core.o: client [W83627HF chip] registered to adapter [SMBus Via Pro adapter at
0400](pos. 0).
i2c-core.o: client [W83627HF subclient] registered to adapter [SMBus Via Pro adapter
at 0400](pos. 1).
i2c-core.o: client [W83627HF subclient] registered to adapter [SMBus Via Pro adapter
at 0400](pos. 2).
eeprom.o version 2.6.2 (20011118)
i2c-core.o: driver EEPROM READER registered.
i2c-core.o: client [EEPROM chip] registered to adapter [SMBus Via Pro adapter at
0400](pos. 3).
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.1
Shorewall:net2fw:ACCEPT:IN=eth0 OUT= MAC=00:a0:cc:e2:3d:b0:00:06:2a:cf:cc:54:08:00
SRC=12.24.207.58 DST=10.45.153.251 LEN=64 TOS=0x00 PREC=0x00 TTL=126 ID=9623 PROTO=47
PPP BSD Compression module registered
PPP Deflate Compression module registered
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
