Hi,
I've posted this problem some time ago, but because it is still
happening with kernel 2.4.19-8mdk, so I send it again.
The scanner is an Agfa SnapScan 156s connected to an aha152x ISA
SCSI-card. It is recognised fine by sane-find-scanner on /dev/sg0
When I press the Acquire Preview button in xscanimage, the system hangs
with the caps lock and scroll lock leds blinking. I can reboot the
machine by pressing Alt-SysRq-b. I don't see any message in
/var/log/kernel related to this crash.
At the first reboot after the crash, the scanner is nog recognized
anymore by the kernel, and this errors relating to the aha152x drivers
are in dmesg:
SCSI subsystem driver Revision: 1.00
aha152x: BIOS test: passed, detected 1 controller(s)
aha152x: resetting bus...
aha152x0: vital data: rev=3, io=0x140 (0x140/0x140), irq=11, scsiid=7,
reconnect=enabled, parity=enabled, synchronous=disabled, delay=1000,
extended translation=disabled
aha152x0: trying software interrupt, ok.
scsi0 : Adaptec 152x SCSI driver; $Revision: 2.5 $
(scsi0:2:0) cannot abort running or disconnected command
(scsi0:2:0) cannot reset current device
aha152x0: scsi reset in
scsi: device set offline - not ready or command retry failed after bus
reset: host 0 channel 0 id 2 lun 0
Nevertheless the aha152x drivers seems to be loaded finally, with the
output of /proc//proc/scsi/aha152x/0 being:
Adaptec 152x SCSI driver; $Revision: 2.5 $
ioports 0x0140 to 0x015f
interrupt 0x0b
disconnection/reconnection enabled
parity checking enabled
synchronous transfers disabled
0 commands currently queued
queue status:
no not yet issued commands
no current command
no disconnected commands
waiting: busfree(selto) SCSISEQ( ); SCSISIG(DATA OUT); INTSTAT (lo);
SSTAT( SELINGO BUSFREE PHASECHG ); SSTAT( ); SXFRCTL0( CH1 ); SIGNAL( );
SELID(00), STCNT(0), SSTAT2( SEMPTY ); SFCNT (0); SCSICNT (0),
OFFCNT(0), SSTAT4( ); DMACNTRL0( 16BIT PIO READ INTEN ); DMASTAT(
DFIFOEMP )
enabled interrupts( )
statistics:
total commands: 8
disconnections: 0
busfree with check condition: 0
busfree without old command: 16
busfree without new command: 8
busfree without done command: 8
busfree without any action: 0
state transitions count time
idle 0 0 0
unknown 0 0 0
seldo 1 1 0
seldi 0 0 0
selto 7 7 0
busfree 9 16 0
msgo 1 1 0
cmd 1 6 0
msgi 0 0 0
status 0 0 0
datai 0 0 0
datao 0 0 0
parerr 0 0 0
rsti 1 1 0
But, as I said already, no scanner detected by dmesg and
sane-find-scanner.
I have attached the complete output of dmesg before and after the crash.
Let me know if more information is needed, I'm not sure how to debug
this problem.
Frederik Himpe
--
http://users.telenet.be/fhimpe/
Linux version 2.4.19-8mdk ([EMAIL PROTECTED]) (gcc version 3.2 (Mandrake
Linux 9.0 3.2-1mdk)) #1 Sat Aug 31 00:49:47 CEST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fffd000 (usable)
BIOS-e820: 000000000fffd000 - 000000000ffff000 (ACPI data)
BIOS-e820: 000000000ffff000 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
255MB LOWMEM available.
Advanced speculative caching feature not present
On node 0 totalpages: 65533
zone(0): 4096 pages.
zone(1): 61437 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=Linux-2.4.19-8 ro root=305 hdg=ide-scsi devfs=mount
ide_setup: hdg=ide-scsi
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 350.800 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 699.59 BogoMIPS
Memory: 256756k/262132k available (1176k kernel code, 4984k reserved, 444k data, 132k
init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
CPU: Intel Pentium II (Deschutes) stepping 01
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 350.8131 MHz.
..... host bus clock speed is 100.2321 MHz.
cpu: 0, clocks: 1002321, slice: 501160
CPU0<T0:1002320,T1:501152,D:8,S:501160,C:1002321>
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf0720, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:04.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: SB audio device quirk - increasing port range
isapnp: AWE32 quirk - adding two ports
isapnp: Card 'Creative SB32 PnP'
isapnp: 1 Plug & Play card detected total
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Diskquotas version dquot_6.5.0 initialized
devfs: v1.12a (20020514) Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x1
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ
SERIAL_PCI ISAPNP enabled
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
PDC20267: IDE controller on PCI bus 00 dev 60
PCI: Found IRQ 4 for device 00:0c.0
PDC20267: chipset revision 2
PDC20267: not 100% native mode: will probe irqs later
PDC20267: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
ide2: BM-DMA at 0xa800-0xa807, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0xa808-0xa80f, BIOS settings: hdg:pio, hdh:pio
ide6: Creative SB32 PnP IDE interface
hda: IBM-DHEA-38451, ATA DISK drive
hdc: QUANTUM FIREBALLP AS40, ATA DISK drive
hdd: CD-ROM 40X/AKU, ATAPI CD/DVD-ROM drive
hde: IBM-DTLA-307045, ATA DISK drive
hdg: PLEXTOR CD-R PX-W8432T, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xd000-0xd007,0xb802 on irq 4
ide3 at 0xb400-0xb407,0xb002 on irq 4
hda: 16514064 sectors (8455 MB) w/472KiB Cache, CHS=1027/255/63, UDMA(33)
hdc: 78198750 sectors (40038 MB) w/1902KiB Cache, CHS=77578/16/63, UDMA(33)
hde: 90069840 sectors (46116 MB) w/1916KiB Cache, CHS=89355/16/63, UDMA(100)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 >
/dev/ide/host0/bus1/target0/lun0: [PTBL] [4867/255/63] p1 p2 < p5 p6 p7 p8 p9 >
/dev/ide/host2/bus0/target0/lun0: [PTBL] [5606/255/63] p1 p2 < p5 p6 p7 p8 >
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 114k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
reiserfs: checking transaction log (device 03:05) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
Mounted devfs on /dev
Freeing unused kernel memory: 132k freed
Real Time Clock Driver v1.10e
Adding Swap: 248968k swap-space (priority -1)
SCSI subsystem driver Revision: 1.00
aha152x: BIOS test: passed, detected 1 controller(s)
aha152x: resetting bus...
aha152x0: vital data: rev=3, io=0x140 (0x140/0x140), irq=11, scsiid=7,
reconnect=enabled, parity=enabled, synchronous=disabled, delay=1000, extended
translation=disabled
aha152x0: trying software interrupt, ok.
scsi0 : Adaptec 152x SCSI driver; $Revision: 2.5 $
Vendor: AGFA Model: SNAPSCAN 1236 Rev: 1.20
Type: Scanner ANSI SCSI revision: 02
hdg: Disabling (U)DMA for PLEXTOR CD-R PX-W8432T
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: PLEXTOR Model: CD-R PX-W8432T Rev: 1.07
Type: CD-ROM ANSI SCSI revision: 02
hdd: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
SGI XFS with ACLs, DMAPI, realtime, quota, no debug enabled
XFS mounting filesystem ide0(3,7)
reiserfs: checking transaction log (device 03:08) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
XFS mounting filesystem ide1(22,6)
XFS mounting filesystem ide1(22,7)
XFS mounting filesystem ide1(22,9)
XFS mounting filesystem ide1(22,8)
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
XFS mounting filesystem ide2(33,8)
hdd: DMA disabled
hdg: DMA disabled
ne.c:v1.10 9/23/94 Donald Becker ([EMAIL PROTECTED])
Last modified Nov 1, 2000 by Paul Gortmaker
NE*000 ethercard probe at 0x240: 00 80 c8 e1 50 17
eth0: NE2000 found at 0x240, using IRQ 3.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 01:19:24 Aug 31 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Assigned IRQ 9 for device 00:04.2
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usbdevfs: remount parameter error
hub.c: USB new device connect on bus1/1, assigned device number 2
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
usb.c: USB device 2 (vend/prod 0x45e/0xe) is not claimed by any active driver.
usb.c: registered new driver hiddev
usb.c: registered new driver hid
usb-uhci.c: interrupt, status 3, frame# 1093
input0: USB HID v1.00 Joystick [Microsoft Microsoft SideWinder game controller] on
usb1:2.0
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
devfs_mk_dir(snd): using old entry in dir: c12ce5c0 ""
devfs_register(snd/controlC1): could not append to parent, err: -17
devfs_register(snd/controlC2): could not append to parent, err: -17
devfs_register(snd/controlC3): could not append to parent, err: -17
devfs_register(snd/controlC4): could not append to parent, err: -17
devfs_register(snd/controlC5): could not append to parent, err: -17
devfs_register(snd/controlC6): could not append to parent, err: -17
devfs_register(snd/controlC7): could not append to parent, err: -17
PCI: Assigned IRQ 9 for device 00:0a.0
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xe4000000
[drm] AGP 0.99 on Intel 440BX @ 0xe4000000 64MB
[drm] Initialized mga 3.0.2 20010321 on minor 0
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
inserting floppy driver for 2.4.19-8mdk
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 6, lun 0
sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
cdrom: This disc doesn't have any tracks I recognize!
Linux version 2.4.19-8mdk ([EMAIL PROTECTED]) (gcc version 3.2 (Mandrake
Linux 9.0 3.2-1mdk)) #1 Sat Aug 31 00:49:47 CEST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fffd000 (usable)
BIOS-e820: 000000000fffd000 - 000000000ffff000 (ACPI data)
BIOS-e820: 000000000ffff000 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
255MB LOWMEM available.
Advanced speculative caching feature not present
On node 0 totalpages: 65533
zone(0): 4096 pages.
zone(1): 61437 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=Linux-2.4.19-8 ro root=305 hdg=ide-scsi devfs=mount
ide_setup: hdg=ide-scsi
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 350.803 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 699.59 BogoMIPS
Memory: 256756k/262132k available (1176k kernel code, 4984k reserved, 444k data, 132k
init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
CPU: Intel Pentium II (Deschutes) stepping 01
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 350.7993 MHz.
..... host bus clock speed is 100.2281 MHz.
cpu: 0, clocks: 1002281, slice: 501140
CPU0<T0:1002272,T1:501120,D:12,S:501140,C:1002281>
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf0720, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:04.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: SB audio device quirk - increasing port range
isapnp: AWE32 quirk - adding two ports
isapnp: Card 'Creative SB32 PnP'
isapnp: 1 Plug & Play card detected total
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Diskquotas version dquot_6.5.0 initialized
devfs: v1.12a (20020514) Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x1
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ
SERIAL_PCI ISAPNP enabled
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
PDC20267: IDE controller on PCI bus 00 dev 60
PCI: Found IRQ 4 for device 00:0c.0
PDC20267: chipset revision 2
PDC20267: not 100% native mode: will probe irqs later
PDC20267: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
ide2: BM-DMA at 0xa800-0xa807, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0xa808-0xa80f, BIOS settings: hdg:pio, hdh:pio
ide6: Creative SB32 PnP IDE interface
hda: IBM-DHEA-38451, ATA DISK drive
hdc: QUANTUM FIREBALLP AS40, ATA DISK drive
hdd: CD-ROM 40X/AKU, ATAPI CD/DVD-ROM drive
hde: IBM-DTLA-307045, ATA DISK drive
hdg: PLEXTOR CD-R PX-W8432T, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xd000-0xd007,0xb802 on irq 4
ide3 at 0xb400-0xb407,0xb002 on irq 4
hda: 16514064 sectors (8455 MB) w/472KiB Cache, CHS=1027/255/63, UDMA(33)
hdc: 78198750 sectors (40038 MB) w/1902KiB Cache, CHS=77578/16/63, UDMA(33)
hde: 90069840 sectors (46116 MB) w/1916KiB Cache, CHS=89355/16/63, UDMA(100)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 >
/dev/ide/host0/bus1/target0/lun0: [PTBL] [4867/255/63] p1 p2 < p5 p6 p7 p8 p9 >
/dev/ide/host2/bus0/target0/lun0: [PTBL] [5606/255/63] p1 p2 < p5 p6 p7 p8 >
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 114k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
reiserfs: checking transaction log (device 03:05) ...
Warning, log replay starting on readonly filesystem
reiserfs: replayed 17 transactions in 4 seconds
Using r5 hash to sort names
ReiserFS version 3.6.25
Mounted devfs on /dev
Freeing unused kernel memory: 132k freed
Real Time Clock Driver v1.10e
Removing [18460 20132 0x0 SD]..done
Removing [18460 19999 0x0 SD]..done
Removing [18460 19991 0x0 SD]..done
Removing [18460 19943 0x0 SD]..done
Removing [18460 19927 0x0 SD]..done
Removing [22 18216 0x0 SD]..done
Removing [22 18181 0x0 SD]..done
Removing [22 18107 0x0 SD]..done
There were 8 uncompleted unlinks/truncates. Completed
Adding Swap: 248968k swap-space (priority -1)
SCSI subsystem driver Revision: 1.00
aha152x: BIOS test: passed, detected 1 controller(s)
aha152x: resetting bus...
aha152x0: vital data: rev=3, io=0x140 (0x140/0x140), irq=11, scsiid=7,
reconnect=enabled, parity=enabled, synchronous=disabled, delay=1000, extended
translation=disabled
aha152x0: trying software interrupt, ok.
scsi0 : Adaptec 152x SCSI driver; $Revision: 2.5 $
(scsi0:2:0) cannot abort running or disconnected command
(scsi0:2:0) cannot reset current device
aha152x0: scsi reset in
scsi: device set offline - not ready or command retry failed after bus reset: host 0
channel 0 id 2 lun 0
hdg: Disabling (U)DMA for PLEXTOR CD-R PX-W8432T
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: PLEXTOR Model: CD-R PX-W8432T Rev: 1.07
Type: CD-ROM ANSI SCSI revision: 02
hdd: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
SGI XFS with ACLs, DMAPI, realtime, quota, no debug enabled
XFS mounting filesystem ide0(3,7)
reiserfs: checking transaction log (device 03:08) ...
reiserfs: replayed 24 transactions in 5 seconds
Using r5 hash to sort names
Removing [180948 350851 0x0 SD]..done
Removing [180948 340939 0x0 SD]..done
Removing [180948 324291 0x0 SD]..done
Removing [180948 305286 0x0 SD]..done
There were 4 uncompleted unlinks/truncates. Completed
ReiserFS version 3.6.25
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
XFS mounting filesystem ide1(22,6)
XFS mounting filesystem ide1(22,7)
XFS mounting filesystem ide1(22,9)
XFS mounting filesystem ide1(22,8)
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
XFS mounting filesystem ide2(33,8)
Starting XFS recovery on filesystem: ide2(33,8) (dev: 33/8)
Ending XFS recovery on filesystem: ide2(33,8) (dev: 33/8)
hdd: DMA disabled
hdg: DMA disabled
ne.c:v1.10 9/23/94 Donald Becker ([EMAIL PROTECTED])
Last modified Nov 1, 2000 by Paul Gortmaker
NE*000 ethercard probe at 0x240: 00 80 c8 e1 50 17
eth0: NE2000 found at 0x240, using IRQ 3.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 01:19:24 Aug 31 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Assigned IRQ 9 for device 00:04.2
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usbdevfs: remount parameter error
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device 2 (vend/prod 0x45e/0xe) is not claimed by any active driver.
usb.c: registered new driver hiddev
usb.c: registered new driver hid
usb-uhci.c: interrupt, status 3, frame# 694
input0: USB HID v1.00 Joystick [Microsoft Microsoft SideWinder game controller] on
usb1:2.0
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
devfs_mk_dir(snd): using old entry in dir: c12ce5c0 ""
devfs_register(snd/controlC1): could not append to parent, err: -17
devfs_register(snd/controlC2): could not append to parent, err: -17
devfs_register(snd/controlC3): could not append to parent, err: -17
devfs_register(snd/controlC4): could not append to parent, err: -17
devfs_register(snd/controlC5): could not append to parent, err: -17
devfs_register(snd/controlC6): could not append to parent, err: -17
devfs_register(snd/controlC7): could not append to parent, err: -17
PCI: Assigned IRQ 9 for device 00:0a.0
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xe4000000
[drm] AGP 0.99 on Intel 440BX @ 0xe4000000 64MB
[drm] Initialized mga 3.0.2 20010321 on minor 0
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
parport0: Printer, HEWLETT-PACKARD DESKJET 890C
lp0: using parport0 (polling).
inserting floppy driver for 2.4.19-8mdk
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 6, lun 0
sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
cdrom: This disc doesn't have any tracks I recognize!
