we concatenated the files to bring them close to and less than 64mb and
the difference was huge without changing anything else
we went from 214 minutes to 3 minutes !
Elia Mazzawi wrote:
Thanks for the suggestions,
I'm going to rerun the same test with close to < 64Mb files and 7 then
14 reducers.
we've done another test to see if more servers would speed up the
cluster,
with 2 nodes down took 322 minutes on the 10X data thats 5.3 hours
vs 214 minutes with all nodes online.
started the test after hdfs marked the nodes as dead, and there were
no timeouts.
332/214 = 55% more time with 5/7 = 71% servers.
so our conclusion is that more servers will make the cluster faster.
Ashish Thusoo wrote:
Try by first just reducing the number of files and increasing the data
in each file so you have close to 64MB of data per file. So in your case
that would amount to about 700-800 files in the 10X test case (instead
of 35000 that you have). See if that give substantially better results
on your larger test case. For the smaller one, I don't think you will be
able to do better than the unix command - the data set is too small.
Ashish
-----Original Message-----
From: Elia Mazzawi [mailto:[EMAIL PROTECTED] Sent:
Tuesday, June 10, 2008 5:00 PM
To: [email protected]
Subject: Re: hadoop benchmarked, too slow to use
so it would make sense for me to configure hadoop for smaller chunks?
Elia Mazzawi wrote:
yes chunk size was 64mb, and each file has some data it used 7 mappers
and 1 reducer.
10X the data took 214 minutes
vs 26 minutes for the smaller set
i uploaded the same data 10 times in different directories ( so more
files, same size )
Ashish Thusoo wrote:
Apart from the setup times, the fact that you have 3500 files means
that you are going after around 220GB of data as each file would have
atleast one chunk (this calculation is assuming a chunk size of
64MB and this assumes that each file has atleast some data).
Mappers would
probably need to read up this amount of data and with 7 nodes you may
just have
14 map slots. I may be wrong here, but just out of curiosity how many
mappers does your job use.
Don't know why the 10X data was not better though if the bad
performance of the smaller test case was due to fragmentation. For
that test did you also increase the number of files, or did you
simply increase the amount of data in each file.
Plus on small sets (of the order of 2-3 GB) of data unix commands
can't really be beaten :)
Ashish
-----Original Message-----
From: Elia Mazzawi [mailto:[EMAIL PROTECTED] Sent:
Tuesday, June 10, 2008 3:56 PM
To: [email protected]
Subject: hadoop benchmarked, too slow to use
Hello,
we were considering using hadoop to process some data, we have it set
up on 8 nodes ( 1 master + 7 slaves)
we filled the cluster up with files that contain tab delimited data.
string \tab string etc
then we ran the example grep with a regular expression to count the
number of each unique starting string.
we had 3500 files containing 3,015,294 lines totaling 5 GB.
to benchmark it we ran
bin/hadoop jar hadoop-0.17.0-examples.jar grep data/* output
'^[a-zA-Z]+\t'
it took 26 minutes
then to compare, we ran this bash command on one of the nodes,
which produced the same output out of the data:
cat * | sed -e s/\ .*// |sort | uniq -c > /tmp/out (sed regexpr is
tab not spaces)
which took 2.5 minutes
Then we added 10X the data into the cluster and reran Hadoop, it took
214 minutes which is less than 10X the time, but still not that
impressive.
so we are seeing a 10X performance penalty for using Hadoop vs the
system commands, is that expected?
we were expecting hadoop to be faster since it is distributed?
perhaps there is too much overhead involved here?
is the data too small?