Author: uwe
Date: 2008-11-28 22:36:51 +0100 (Fri, 28 Nov 2008)
New Revision: 3779
Added:
trunk/util/flashrom/sb600spi.c
Modified:
trunk/util/flashrom/Makefile
trunk/util/flashrom/chipset_enable.c
trunk/util/flashrom/flash.h
trunk/util/flashrom/flashrom.c
trunk/util/flashrom/spi.c
trunk/util/flashrom/spi.h
Log:
Add support for the AMD/ATI SB600 southbridge SPI functionality.
This has been tested by Uwe Hermann on an RS690/SB600 board.
Signed-off-by: Jason Wang <[EMAIL PROTECTED]>
Reviewed-by: Joe Bao <[EMAIL PROTECTED]>
Acked-by: Uwe Hermann <[EMAIL PROTECTED]>
Modified: trunk/util/flashrom/Makefile
===================================================================
--- trunk/util/flashrom/Makefile 2008-11-28 12:09:17 UTC (rev 3778)
+++ trunk/util/flashrom/Makefile 2008-11-28 21:36:51 UTC (rev 3779)
@@ -29,7 +29,7 @@
w49f002u.o 82802ab.o pm49fl00x.o sst49lf040.o en29f002a.o \
sst49lfxxxc.o sst_fwhub.o layout.o cbtable.o flashchips.o \
flashrom.o w39v080fa.o sharplhf00l04.o w29ee011.o spi.o it87spi.o \
- ichspi.o w39v040c.o
+ ichspi.o w39v040c.o sb600spi.o
all: pciutils dep $(PROGRAM)
Modified: trunk/util/flashrom/chipset_enable.c
===================================================================
--- trunk/util/flashrom/chipset_enable.c 2008-11-28 12:09:17 UTC (rev
3778)
+++ trunk/util/flashrom/chipset_enable.c 2008-11-28 21:36:51 UTC (rev
3779)
@@ -647,21 +647,36 @@
static int enable_flash_sb600(struct pci_dev *dev, const char *name)
{
- uint32_t old, new;
+ uint32_t tmp, low_bits, num;
uint8_t reg;
- /* Clear ROM Protect 0-3 */
+ low_bits = tmp = pci_read_long(dev, 0xa0);
+ low_bits &= ~0xffffc000; /* for mmap aligning requirements */
+ low_bits &= 0xfffffff0; /* remove low 4 bits */
+ tmp &= 0xffffc000;
+ printf_debug("SPI base address is at 0x%x\n", tmp + low_bits);
+
+ sb600_spibar = mmap(0, 0x4000, PROT_READ | PROT_WRITE, MAP_SHARED,
+ fd_mem, (off_t)tmp);
+ if (sb600_spibar == MAP_FAILED) {
+ perror("Can't mmap memory using " MEM_DEV);
+ exit(1);
+ }
+ sb600_spibar += low_bits;
+
+ /* Clear ROM protect 0-3. */
for (reg = 0x50; reg < 0x60; reg += 4) {
- old = pci_read_long(dev, reg);
- new = old & 0xFFFFFFFC;
- if (new != old) {
- pci_write_byte(dev, reg, new);
- if (pci_read_long(dev, reg) != new) {
- printf("tried to set 0x%x to 0x%x on %s failed
(WARNING ONLY)\n", 0x50, new, name);
- }
- }
+ num = pci_read_long(dev, reg);
+ num &= 0xfffffffc;
+ pci_write_byte(dev, reg, num);
}
+ flashbus = BUS_TYPE_SB600_SPI;
+
+ /* Enable SPI ROM in SB600 PM register. */
+ OUTB(0x8f, 0xcd6);
+ OUTB(0x0e, 0xcd7);
+
return 0;
}
Modified: trunk/util/flashrom/flash.h
===================================================================
--- trunk/util/flashrom/flash.h 2008-11-28 12:09:17 UTC (rev 3778)
+++ trunk/util/flashrom/flash.h 2008-11-28 21:36:51 UTC (rev 3779)
@@ -414,6 +414,7 @@
BUS_TYPE_ICH7_SPI,
BUS_TYPE_ICH9_SPI,
BUS_TYPE_IT87XX_SPI,
+ BUS_TYPE_SB600_SPI,
BUS_TYPE_VIA_SPI
} flashbus_t;
@@ -497,6 +498,14 @@
int it8716f_spi_chip_read(struct flashchip *flash, uint8_t *buf);
int it8716f_spi_chip_write(struct flashchip *flash, uint8_t *buf);
+/* sb600spi.c */
+int sb600_spi_command(unsigned int writecnt, unsigned int readcnt,
+ const unsigned char *writearr, unsigned char *readarr);
+int sb600_spi_read(struct flashchip *flash, uint8_t *buf);
+int sb600_spi_write(struct flashchip *flash, uint8_t *buf);
+uint8_t sb600_read_status_register(void);
+extern uint8_t volatile *sb600_spibar;
+
/* jedec.c */
uint8_t oddparity(uint8_t val);
void toggle_ready_jedec(volatile uint8_t *dst);
Modified: trunk/util/flashrom/flashrom.c
===================================================================
--- trunk/util/flashrom/flashrom.c 2008-11-28 12:09:17 UTC (rev 3778)
+++ trunk/util/flashrom/flashrom.c 2008-11-28 21:36:51 UTC (rev 3779)
@@ -463,7 +463,7 @@
perror(filename);
exit(1);
}
- printf("Force reading flash...");
+ printf("Force reading flash... ");
if (!flashes[0]->read)
memcpy(buf, (const char
*)flashes[0]->virtual_memory, size);
else
@@ -476,7 +476,7 @@
fwrite(buf, sizeof(char), size, image);
fclose(image);
- printf("done\n");
+ printf("done.\n");
free(buf);
exit(0);
}
@@ -533,19 +533,20 @@
buf = (uint8_t *) calloc(size, sizeof(char));
if (erase_it) {
- printf("Erasing flash chip.\n");
+ printf("Erasing flash chip... ");
if (!flash->erase) {
fprintf(stderr, "Error: flashrom has no erase function
for this flash chip.\n");
return 1;
}
flash->erase(flash);
+ printf("done.\n");
exit(0);
} else if (read_it) {
if ((image = fopen(filename, "w")) == NULL) {
perror(filename);
exit(1);
}
- printf("Reading Flash...");
+ printf("Reading flash... ");
if (flash->read == NULL)
memcpy(buf, (const char *)flash->virtual_memory, size);
else
@@ -557,7 +558,7 @@
fwrite(buf, sizeof(char), size, image);
fclose(image);
- printf("done\n");
+ printf("done.\n");
} else {
struct stat image_stat;
Added: trunk/util/flashrom/sb600spi.c
===================================================================
--- trunk/util/flashrom/sb600spi.c (rev 0)
+++ trunk/util/flashrom/sb600spi.c 2008-11-28 21:36:51 UTC (rev 3779)
@@ -0,0 +1,175 @@
+/*
+ * This file is part of the flashrom project.
+ *
+ * Copyright (C) 2008 Stefan Wildemann <[EMAIL PROTECTED]>
+ * Copyright (C) 2008 Claus Gindhart <[EMAIL PROTECTED]>
+ * Copyright (C) 2008 Dominik Geyer <[EMAIL PROTECTED]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <stdio.h>
+#include <string.h>
+#include <stdint.h>
+#include <sys/mman.h>
+#include <pci/pci.h>
+#include "flash.h"
+#include "spi.h"
+
+typedef struct _spi_controller {
+ unsigned int spi_cntrl0; /* 00h */
+ unsigned int restrictedcmd1; /* 04h */
+ unsigned int restrictedcmd2; /* 08h */
+ unsigned int spi_cntrl1; /* 0ch */
+ unsigned int spi_cmdvalue0; /* 10h */
+ unsigned int spi_cmdvalue1; /* 14h */
+ unsigned int spi_cmdvalue2; /* 18h */
+ unsigned int spi_fakeid; /* 1Ch */
+} sb600_spi_controller;
+
+sb600_spi_controller *spi_bar = NULL;
+uint8_t volatile *sb600_spibar;
+
+int sb600_spi_read(struct flashchip *flash, uint8_t *buf)
+{
+ int rc = 0, i;
+ int total_size = flash->total_size * 1024;
+ int page_size = 8;
+
+ for (i = 0; i < total_size / page_size; i++)
+ spi_nbyte_read(i * page_size, (void *)(buf + i * page_size),
+ page_size);
+ return rc;
+}
+
+uint8_t sb600_read_status_register(void)
+{
+ const unsigned char cmd[0x02] = { JEDEC_RDSR, 0x00 };
+ unsigned char readarr[JEDEC_RDSR_INSIZE];
+
+ /* Read Status Register */
+ spi_command(sizeof(cmd), sizeof(readarr), cmd, readarr);
+ return readarr[0];
+}
+
+int sb600_spi_write(struct flashchip *flash, uint8_t *buf)
+{
+ int rc = 0, i;
+ int total_size = flash->total_size * 1024;
+
+ /* Erase first */
+ printf("Erasing flash before programming... ");
+ flash->erase(flash);
+ printf("done.\n");
+
+ printf("Programming flash");
+ for (i = 0; i < total_size; i++, buf++) {
+ spi_disable_blockprotect();
+ spi_write_enable();
+ spi_byte_program(i, *buf);
+ /* wait program complete. */
+ if (i % 0x8000 == 0)
+ printf(".");
+ while (spi_read_status_register() & JEDEC_RDSR_BIT_WIP)
+ ;
+ }
+ printf(" done.\n");
+ return rc;
+}
+
+void reset_internal_fifo_pointer(void)
+{
+ sb600_spibar[2] |= 0x10;
+
+ while (sb600_spibar[0xD] & 0x7)
+ printf("reset\n");
+}
+
+void execute_command(void)
+{
+ sb600_spibar[2] |= 1;
+
+ while (sb600_spibar[2] & 1)
+ ;
+}
+
+int sb600_spi_command(unsigned int writecnt, unsigned int readcnt,
+ const unsigned char *writearr, unsigned char *readarr)
+{
+ int count;
+ /* First byte is cmd which can not being sent through FIFO. */
+ unsigned char cmd = *writearr++;
+
+ writecnt--;
+
+ spi_bar = (sb600_spi_controller *) sb600_spibar;
+
+ printf_debug("%s, cmd=%x, writecnt=%x, readcnt=%x\n",
+ __func__, cmd, writecnt, readcnt);
+
+ if (readcnt > 8) {
+ printf("%s, SB600 SPI controller can not receive %d bytes, "
+ "which is limited with 8 bytes\n", __func__, readcnt);
+ return 1;
+ }
+
+ if (writecnt > 8) {
+ printf("%s, SB600 SPI controller can not sent %d bytes, "
+ "which is limited with 8 bytes\n", __func__, writecnt);
+ return 1;
+ }
+
+ sb600_spibar[0] = cmd;
+ sb600_spibar[1] = readcnt << 4 | (writecnt);
+
+ /* Before we use the FIFO, reset it first. */
+ reset_internal_fifo_pointer();
+
+ /* Send the write byte to FIFO. */
+ for (count = 0; count < writecnt; count++, writearr++) {
+ printf_debug(" [%x]", *writearr);
+ sb600_spibar[0xC] = *writearr;
+ }
+ printf_debug("\n");
+
+ /*
+ * We should send the data by sequence, which means we need to reset
+ * the FIFO pointer to the first byte we want to send.
+ */
+ reset_internal_fifo_pointer();
+
+ execute_command();
+
+ /*
+ * After the command executed, we should find out the index of the
+ * received byte. Here we just reset the FIFO pointer, skip the
+ * writecnt, is there anyone who have anther method to replace it?
+ */
+ reset_internal_fifo_pointer();
+
+ for (count = 0; count < writecnt; count++) {
+ cmd = sb600_spibar[0xC]; /* Skip the byte we send. */
+ printf_debug("[ %2x]", cmd);
+ }
+
+ printf_debug("The FIFO pointer 6 is %d.\n", sb600_spibar[0xd] & 0x07);
+ for (count = 0; count < readcnt; count++, readarr++) {
+ *readarr = sb600_spibar[0xC];
+ printf_debug("[%02x]", *readarr);
+ }
+ printf_debug("\n");
+
+ return 0;
+}
Modified: trunk/util/flashrom/spi.c
===================================================================
--- trunk/util/flashrom/spi.c 2008-11-28 12:09:17 UTC (rev 3778)
+++ trunk/util/flashrom/spi.c 2008-11-28 21:36:51 UTC (rev 3779)
@@ -42,6 +42,8 @@
case BUS_TYPE_ICH9_SPI:
case BUS_TYPE_VIA_SPI:
return ich_spi_command(writecnt, readcnt, writearr, readarr);
+ case BUS_TYPE_SB600_SPI:
+ return sb600_spi_command(writecnt, readcnt, writearr, readarr);
default:
printf_debug
("%s called, but no SPI chipset/strapping detected\n",
@@ -157,6 +159,7 @@
case BUS_TYPE_ICH7_SPI:
case BUS_TYPE_ICH9_SPI:
case BUS_TYPE_VIA_SPI:
+ case BUS_TYPE_SB600_SPI:
return probe_spi_rdid_generic(flash, 4);
default:
printf_debug("4b ID not supported on this SPI controller\n");
@@ -229,7 +232,13 @@
unsigned char readarr[JEDEC_RDSR_INSIZE];
/* Read Status Register */
- spi_command(sizeof(cmd), sizeof(readarr), cmd, readarr);
+ if (flashbus == BUS_TYPE_SB600_SPI) {
+ /* SB600 uses a different way to read status register. */
+ return sb600_read_status_register();
+ } else {
+ spi_command(sizeof(cmd), sizeof(readarr), cmd, readarr);
+ }
+
return readarr[0];
}
@@ -464,6 +473,14 @@
return 0;
}
+int spi_write_status_enable()
+{
+ const unsigned char cmd[JEDEC_EWSR_OUTSIZE] = { JEDEC_EWSR };
+
+ /* Send EWSR (Enable Write Status Register). */
+ return spi_command(JEDEC_EWSR_OUTSIZE, JEDEC_EWSR_INSIZE, cmd, NULL);
+}
+
/*
* This is according the SST25VF016 datasheet, who knows it is more
* generic that this...
@@ -500,9 +517,9 @@
/* If there is block protection in effect, unprotect it first. */
if ((status & 0x3c) != 0) {
printf_debug("Some block protection in effect, disabling\n");
- result = spi_write_enable();
+ result = spi_write_status_enable();
if (result) {
- printf_debug("spi_write_enable failed\n");
+ printf_debug("spi_write_status_enable failed\n");
return result;
}
result = spi_write_status_register(status & ~0x3c);
@@ -532,6 +549,8 @@
switch (flashbus) {
case BUS_TYPE_IT87XX_SPI:
return it8716f_spi_chip_read(flash, buf);
+ case BUS_TYPE_SB600_SPI:
+ return sb600_spi_read(flash, buf);
case BUS_TYPE_ICH7_SPI:
case BUS_TYPE_ICH9_SPI:
case BUS_TYPE_VIA_SPI:
@@ -550,6 +569,8 @@
switch (flashbus) {
case BUS_TYPE_IT87XX_SPI:
return it8716f_spi_chip_write(flash, buf);
+ case BUS_TYPE_SB600_SPI:
+ return sb600_spi_write(flash, buf);
case BUS_TYPE_ICH7_SPI:
case BUS_TYPE_ICH9_SPI:
case BUS_TYPE_VIA_SPI:
Modified: trunk/util/flashrom/spi.h
===================================================================
--- trunk/util/flashrom/spi.h 2008-11-28 12:09:17 UTC (rev 3778)
+++ trunk/util/flashrom/spi.h 2008-11-28 21:36:51 UTC (rev 3779)
@@ -80,6 +80,11 @@
#define JEDEC_RDSR_INSIZE 0x01
#define JEDEC_RDSR_BIT_WIP (0x01 << 0)
+/* Write Status Enable */
+#define JEDEC_EWSR 0x50
+#define JEDEC_EWSR_OUTSIZE 0x01
+#define JEDEC_EWSR_INSIZE 0x00
+
/* Write Status Register */
#define JEDEC_WRSR 0x01
#define JEDEC_WRSR_OUTSIZE 0x02
--
coreboot mailing list: [email protected]
http://www.coreboot.org/mailman/listinfo/coreboot
