Hi,
>> So, I've added the missing ACPI part, but it seems that some more work is
>> needed to get parport interrupt driven working.
>I just did a mistake and set no address in the IO Section.
>
>There's already another patch on the list (which was filtered by my
>spam-filter,
>and therefore I did the job again).
>The difference between my patch, and the one from Andreas are minimal, but I
>added the ECP device which is necessary to get Parport full functional
>(hopefully I did everything correct, as I can't test this without Parport
>devices.)
my printer works fine (interrupt driven). From dmesg:
old dmesg:
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: parse allocated resources
pnp 00:00: add io 0xcf8-0xcff flags 0x1
pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
pnp 00:01: parse allocated resources
pnp 00:01: add io 0x60-0x60 flags 0x1
pnp 00:01: add io 0x64-0x64 flags 0x1
pnp 00:01: add irq 1 flags 0x1
pnp 00:01: Plug and Play ACPI device, IDs PNP0303 (active)
pnp 00:02: parse allocated resources
pnp 00:02: add io 0x378-0x387 flags 0x0
pnp 00:02: add irq 7 flags 0x1
pnp 00:02: Plug and Play ACPI device, IDs PNP0400 (active)
pnp 00:03: parse allocated resources
pnp 00:03: add io 0x60-0x60 flags 0x1
pnp 00:03: add io 0x64-0x64 flags 0x1
pnp 00:03: add irq 12 flags 0x1
pnp 00:03: Plug and Play ACPI device, IDs PNP0f13 (active)
pnp 00:04: parse allocated resources
pnp 00:04: add io 0x3f0-0x3f5 flags 0x1
pnp 00:04: add io 0x3f7-0x3f7 flags 0x1
pnp 00:04: add irq 6 flags 0x1
pnp 00:04: add dma 2 flags 0x0
pnp 00:04: Plug and Play ACPI device, IDs PNP0700 (active)
pnp: PnP ACPI: found 5 devices
new dmesg:
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: parse allocated resources
pnp 00:00: add io 0xcf8-0xcff flags 0x1
pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
pnp 00:01: parse allocated resources
pnp 00:01: add io 0x60-0x60 flags 0x1
pnp 00:01: add io 0x64-0x64 flags 0x1
pnp 00:01: add irq 1 flags 0x1
pnp 00:01: Plug and Play ACPI device, IDs PNP0303 (active)
pnp 00:02: parse allocated resources
pnp 00:02: add io 0x60-0x60 flags 0x1
pnp 00:02: add io 0x64-0x64 flags 0x1
pnp 00:02: add irq 12 flags 0x1
pnp 00:02: Plug and Play ACPI device, IDs PNP0f13 (active)
pnp 00:03: parse allocated resources
pnp 00:03: add io 0x3f0-0x3f5 flags 0x1
pnp 00:03: add io 0x3f7-0x3f7 flags 0x1
pnp 00:03: add irq 6 flags 0x1
pnp 00:03: add dma 2 flags 0x0
pnp 00:03: Plug and Play ACPI device, IDs PNP0700 (active)
pnp 00:04: parse allocated resources
pnp 00:04: add io 0x378-0x37f flags 0x1
pnp 00:04: add irq 7 flags 0x1
pnp 00:04: Plug and Play ACPI device, IDs PNP0400 (active)
pnp 00:05: parse allocated resources
pnp 00:05: add io 0x378-0x37b flags 0x1
pnp 00:05: add io 0x778-0x77b flags 0x1
pnp 00:05: add irq 7 flags 0x1
pnp 00:05: add dma 0 flags 0x0
pnp 00:05: Plug and Play ACPI device, IDs PNP0401 (active)
pnp: PnP ACPI: found 6 devices
>
>The attached patch activates changes the LPT port from polling to interrupt-
>driven, and should be fine.
>
>Signed-off-by: Harald Gutmann <harald.gutmann at gmx.net>
Ignoring that I do not know how to check the ECP device:
Acked-by: Andreas B. Mundt <andi.mundt at web.de>
Kind regards,
Andi
--
coreboot mailing list: coreboot@coreboot.org
http://www.coreboot.org/mailman/listinfo/coreboot
