Hi all,
an update:
I installed a secondary build system (ubuntu), i build everything from
scratch; seabios and coreboot r5575, r5600 and r5631, all these where
working fine. But booting them all failed.
I tried everything i could think of;
1. Swapped hardware; memory, system board, harddisks, ide-controller
(pri. versus sec.).
2. Swapped development systems (debian versus ubuntu)
3.
I attached two bootlogs. for analise
1. with 80Gb harddisk.
- up to 7 secs in the boot process all is fine
- then 120 secs of silence, and last the message from udevd
2. with 1Gb compact flash disk (which has a DMA problem, but its able to
boot futher in the Linux boot secuence.
- up to 6 secs in the boot process all is fine
- then 120 secs are lost to the DMA problem of the CF card, the system
booted before with de DMA failures just fine it takes only 120 secs
extra.
- then 120 secs of silence, and the message from udevd
- then some more output on starting the cardbus and others.
- final message adding the swap on /dev/hda5 and then silence again.
I hope that anyone can help me with this silly problem, please don't
just throw a term through the mail, like "fix the DMA problem", but give
some pointers how to solve it in my configuration.
Marc
On Fri, 2010-06-11 at 20:43 +0200, mbertens wrote:
> On Thu, 2010-06-10 at 12:31 -0600, Myles Watson wrote:
> > > >> > Anyone any ideas
> > Have you tried to boot the factory BIOS? Are these all cold boots? Did
> > cold boot always work?
> >
> > Thanks,
> > Myles
> >
> I have two systems here on the table;
> 1.A. original BIOS (insyde) boots just fine with FreeBSD
> B with external ROM on the JDEBUG connector (see
> http://www.coreboot.org/Tutorials:Nokia_IP530#J-DEBUG ) im not able to
> boot coreboot (R5628 or 5600 with my patches which worked before).
> 2. The on-board flash contains R5512 that does not boot as well and this
> one booted before too.
>
> So as you can understand i'm a little lost
>
> I tried adding bayou with payloads seabios and coreinfo, seabios is
> starting as before, but coreinfo doesn't do anything.
>
>
> Marc
>
>
>
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2010.06.13 09:59:25 =~=~=~=~=~=~=~=~=~=~=~=
coreboot-4.0-r5631-ip530 Sun Jun 13 09:26:00 CEST 2010 starting...
SMBus controller enabled
Northbridge prior to SDRAM init:
Found DIMM in slot 00
Found DIMM in slot 01
PGPOL[BPR] has been set to 0x0f
RPS has been set to 0x00aa
NBXECC[31:24] has been set to 0xff
DRAMC has been set to 0x08
RAM Enable 1: Apply NOP
RAM Enable 2: Precharge all
RAM Enable 3: CBR
RAM Enable 4: Mode register set
RAM Enable 5: Normal operation
RAM Enable 6: Enable refresh
Enabling refresh (DRAMC = 0x09) for DIMM 00
Enabling refresh (DRAMC = 0x09) for DIMM 01
Northbridge following SDRAM init:
Loading stage image.
Check CBFS header at fffeffe0
magic is 4f524243
Found CBFS header at fffeffe0
Check fallback/coreboot_ram
Stage: loading fallback/coreboot_ram @ 0x100000 (147456 bytes), entry @ 0x100000
Stage: done loading.
Jumping to image.
POST: 0x80
POST: 0x39
coreboot-4.0-r5631-ip530 Sun Jun 13 09:26:00 CEST 2010 booting...
POST: 0x40
Calibrating delay loop...
end 5da79ddd, start 23d0d24c
32-bit delta 925
calibrate_tsc 32-bit result is 925
clocks_per_usec: 925
Enumerating buses...
Show all devs...Before Device Enumeration.
Root Device: enabled 1
APIC_CLUSTER: 0: enabled 1
APIC: 00: enabled 1
PCI_DOMAIN: 0000: enabled 1
PCI: 00:00.0: enabled 1
PCI: 00:01.0: enabled 1
PCI: 00:07.0: enabled 1
PNP: 03f0.0: enabled 0
PNP: 03f0.3: enabled 0
PNP: 03f0.4: enabled 1
PNP: 03f0.5: enabled 1
PNP: 03f0.7: enabled 1
PNP: 03f0.6: enabled 1
PNP: 03f0.8: enabled 1
PNP: 03f0.a: enabled 0
PCI: 00:07.1: enabled 1
PCI: 00:07.2: enabled 0
PCI: 00:07.3: enabled 0
Compare with tree...
Root Device: enabled 1
APIC_CLUSTER: 0: enabled 1
APIC: 00: enabled 1
PCI_DOMAIN: 0000: enabled 1
PCI: 00:00.0: enabled 1
PCI: 00:01.0: enabled 1
PCI: 00:07.0: enabled 1
PNP: 03f0.0: enabled 0
PNP: 03f0.3: enabled 0
PNP: 03f0.4: enabled 1
PNP: 03f0.5: enabled 1
PNP: 03f0.7: enabled 1
PNP: 03f0.6: enabled 1
PNP: 03f0.8: enabled 1
PNP: 03f0.a: enabled 0
PCI: 00:07.1: enabled 1
PCI: 00:07.2: enabled 0
PCI: 00:07.3: enabled 0
Setting up IP530-Super I/O devices
--Register 0x03 = 80 := 0x80
--Register 0x22 = 30 := 0x30
--Register 0x24 = 84 := 0x84
scan_static_bus for Root Device
APIC_CLUSTER: 0 enabled
Finding PCI configuration type.
PCI: Using configuration type 1
POST: 0x5f
PCI_DOMAIN: 0000 enabled
PCI_DOMAIN: 0000 scanning...
PCI: pci_scan_bus for bus 00
POST: 0x24
PCI: 00:00.0 [8086/7190] ops
PCI: 00:00.0 [8086/7190] enabled
PCI: 00:01.0 [8086/7191] enabled
PCI: 00:07.0 [8086/7110] bus ops
PCI: 00:07.0 [8086/7110] enabled
PCI: 00:07.1 [8086/7111] ops
PCI: 00:07.1 [8086/7111] enabled
PCI: 00:07.2 [8086/7112] ops
PCI: 00:07.2 [8086/7112] disabled
PCI: 00:07.3 [8086/7113] bus ops
PCI: 00:07.3 [8086/7113] disabled
malloc Enter, size 68, free_mem_ptr 00120000
malloc 00120000
PCI: 00:0d.0 [1011/0019] ops
PCI: 00:0d.0 [1011/0019] enabled
malloc Enter, size 68, free_mem_ptr 00120044
malloc 00120044
PCI: 00:0e.0 [1011/0019] ops
PCI: 00:0e.0 [1011/0019] enabled
malloc Enter, size 68, free_mem_ptr 00120088
malloc 00120088
PCI: 00:0f.0 [104c/ac1c] ops
PCI: 00:0f.0 [104c/ac1c] enabled
malloc Enter, size 68, free_mem_ptr 001200cc
malloc 001200cc
PCI: 00:0f.1 [104c/ac1c] ops
PCI: 00:0f.1 [104c/ac1c] enabled
POST: 0x25
do_pci_scan_bridge for PCI: 00:01.0
malloc Enter, size 24, free_mem_ptr 00120110
malloc 00120110
PCI: pci_scan_bus for bus 01
POST: 0x24
malloc Enter, size 68, free_mem_ptr 00120128
malloc 00120128
Capability: type 0x01 @ 0xdc
Capability: type 0x01 @ 0xdc
PCI: 01:00.0 [1011/0023] enabled
POST: 0x25
do_pci_scan_bridge for PCI: 01:00.0
malloc Enter, size 24, free_mem_ptr 0012016c
malloc 0012016c
PCI: pci_scan_bus for bus 02
POST: 0x24
malloc Enter, size 68, free_mem_ptr 00120184
malloc 00120184
PCI: 02:04.0 [1011/0019] ops
PCI: 02:04.0 [1011/0019] enabled
malloc Enter, size 68, free_mem_ptr 001201c8
malloc 001201c8
PCI: 02:05.0 [1011/0019] ops
PCI: 02:05.0 [1011/0019] enabled
POST: 0x25
PCI: pci_scan_bus returning with max=002
POST: 0x55
do_pci_scan_bridge returns max 2
PCI: pci_scan_bus returning with max=002
POST: 0x55
do_pci_scan_bridge returns max 2
scan_static_bus for PCI: 00:07.0
Found SMSC Super I/O (ID=0x44, rev=0x03)
malloc Enter, size 2560, free_mem_ptr 0012020c
malloc 0012020c
PNP: 03f0.0 disabled
PNP: 03f0.3 disabled
PNP: 03f0.4 enabled
PNP: 03f0.5 enabled
PNP: 03f0.7 enabled
PNP: 03f0.6 enabled
PNP: 03f0.8 enabled
PNP: 03f0.a disabled
scan_static_bus for PCI: 00:07.0 done
PCI: pci_scan_bus returning with max=002
POST: 0x55
scan_static_bus for Root Device done
done
POST: 0x66
Allocating resources...
Reading resources...
Root Device read_resources bus 0 link: 0
APIC_CLUSTER: 0 read_resources bus 0 link: 0
APIC: 00 missing read_resources
APIC_CLUSTER: 0 read_resources bus 0 link: 0 done
PCI_DOMAIN: 0000 read_resources bus 0 link: 0
PCI: 00:01.0 read_resources bus 1 link: 0
PCI: 01:00.0 read_resources bus 2 link: 0
PCI: 01:00.0 read_resources bus 2 link: 0 done
PCI: 00:01.0 read_resources bus 1 link: 0 done
PCI: 00:07.0 read_resources bus 0 link: 0
PCI: 00:07.0 read_resources bus 0 link: 0 done
PCI: 00:0f.0 missing read_resources
PCI: 00:0f.1 missing read_resources
PCI_DOMAIN: 0000 read_resources bus 0 link: 0 done
Root Device read_resources bus 0 link: 0 done
Done reading resources.
Show resources in subtree (Root Device)...After reading.
Root Device child on link 0 APIC_CLUSTER: 0
APIC_CLUSTER: 0 child on link 0 APIC: 00
APIC: 00
PCI_DOMAIN: 0000 child on link 0 PCI: 00:00.0
PCI_DOMAIN: 0000 resource base 0 size 0 align 0 gran 0 limit ffff flags 40040100 index 10000000
PCI_DOMAIN: 0000 resource base 0 size 0 align 0 gran 0 limit ffffffff flags 40040200 index 10000100
PCI: 00:00.0
PCI: 00:00.0 resource base 0 size 10000000 align 28 gran 28 limit ffffffff flags 1200 index 10
PCI: 00:01.0 child on link 0 PCI: 01:00.0
PCI: 00:01.0 resource base 0 size 0 align 12 gran 12 limit ffff flags 80102 index 1c
PCI: 00:01.0 resource base 0 size 0 align 20 gran 20 limit ffffffff flags 81202 index 24
PCI: 00:01.0 resource base 0 size 0 align 20 gran 20 limit ffffffff flags 80202 index 20
PCI: 01:00.0 child on link 0 PCI: 02:04.0
PCI: 01:00.0 resource base 0 size 0 align 12 gran 12 limit ffffffff flags 80102 index 1c
PCI: 01:00.0 resource base 0 size 0 align 20 gran 20 limit ffffffffffffffff flags 81202 index 24
PCI: 01:00.0 resource base 0 size 0 align 20 gran 20 limit ffffffff flags 80202 index 20
PCI: 02:04.0
PCI: 02:04.0 resource base 0 size 80 align 7 gran 7 limit ffff flags 100 index 10
PCI: 02:04.0 resource base 0 size 400 align 10 gran 10 limit ffffffff flags 200 index 14
PCI: 02:04.0 resource base 0 size 40000 align 18 gran 18 limit ffffffff flags 2200 index 30
PCI: 02:05.0
PCI: 02:05.0 resource base 0 size 80 align 7 gran 7 limit ffff flags 100 index 10
PCI: 02:05.0 resource base 0 size 400 align 10 gran 10 limit ffffffff flags 200 index 14
PCI: 02:05.0 resource base 0 size 40000 align 18 gran 18 limit ffffffff flags 2200 index 30
PCI: 00:07.0 child on link 0 PNP: 03f0.0
PCI: 00:07.0 resource base 0 size 1000 align 0 gran 0 limit ffff flags c0000100 index 1
PCI: 00:07.0 resource base ff800000 size 800000 align 0 gran 0 limit 0 flags c0000200 index 2
PCI: 00:07.0 resource base fec00000 size 1000 align 0 gran 0 limit 0 flags c0000200 index 3
PNP: 03f0.0
PNP: 03f0.0 resource base 0 size 8 align 3 gran 3 limit 7ff flags 100 index 60
PNP: 03f0.0 resource base 0 size 1 align 0 gran 0 limit 0 flags 400 index 70
PNP: 03f0.0 resource base 0 size 1 align 0 gran 0 limit 0 flags 800 index 74
PNP: 03f0.3
PNP: 03f0.3 resource base 0 size 8 align 3 gran 3 limit 7ff flags 100 index 60
PNP: 03f0.3 resource base 0 size 1 align 0 gran 0 limit 0 flags 400 index 70
PNP: 03f0.3 resource base 0 size 1 align 0 gran 0 limit 0 flags 800 index 74
PNP: 03f0.4
PNP: 03f0.4 resource base 3f8 size 8 align 3 gran 3 limit 7ff flags c0000100 index 60
PNP: 03f0.4 resource base 4 size 1 align 0 gran 0 limit 0 flags c0000400 index 70
PNP: 03f0.5
PNP: 03f0.5 resource base 2f8 size 8 align 3 gran 3 limit 7ff flags c0000100 index 60
PNP: 03f0.5 resource base 3 size 1 align 0 gran 0 limit 0 flags c0000400 index 70
PNP: 03f0.7
PNP: 03f0.7 resource base 0 size 1 align 0 gran 0 limit ffffffff flags 100 index 60
PNP: 03f0.7 resource base 0 size 1 align 0 gran 0 limit ffffffff flags 100 index 62
PNP: 03f0.7 resource base 0 size 1 align 0 gran 0 limit 0 flags 400 index 70
PNP: 03f0.7 resource base 0 size 1 align 0 gran 0 limit 0 flags 400 index 72
PNP: 03f0.6
PNP: 03f0.8
PNP: 03f0.a
PCI: 00:07.1
PCI: 00:07.1 resource base 0 size 10 align 4 gran 4 limit ffff flags 100 index 20
PCI: 00:07.2
PCI: 00:07.3
PCI: 00:0d.0
PCI: 00:0d.0 resource base 0 size 80 align 7 gran 7 limit ffff flags 100 index 10
PCI: 00:0d.0 resource base 0 size 400 align 10 gran 10 limit ffffffff flags 200 index 14
PCI: 00:0d.0 resource base 0 size 40000 align 18 gran 18 limit ffffffff flags 2200 index 30
PCI: 00:0e.0
PCI: 00:0e.0 resource base 0 size 80 align 7 gran 7 limit ffff flags 100 index 10
PCI: 00:0e.0 resource base 0 size 400 align 10 gran 10 limit ffffffff flags 200 index 14
PCI: 00:0e.0 resource base 0 size 40000 align 18 gran 18 limit ffffffff flags 2200 index 30
PCI: 00:0f.0
PCI: 00:0f.1
PCI_DOMAIN: 0000 compute_resources_io: base: 0 size: 0 align: 0 gran: 0 limit: ffff
PCI: 00:01.0 compute_resources_io: base: 0 size: 0 align: 12 gran: 12 limit: ffff
PCI: 01:00.0 compute_resources_io: base: 0 size: 0 align: 12 gran: 12 limit: ffffffff
PCI: 02:04.0 10 * [0x0 - 0x7f] io
PCI: 02:05.0 10 * [0x80 - 0xff] io
PCI: 01:00.0 compute_resources_io: base: 100 size: 1000 align: 12 gran: 12 limit: ffff done
PCI: 01:00.0 1c * [0x0 - 0xfff] io
PCI: 00:01.0 compute_resources_io: base: 1000 size: 1000 align: 12 gran: 12 limit: ffff done
PCI: 00:01.0 1c * [0x0 - 0xfff] io
PCI: 00:0d.0 10 * [0x1000 - 0x107f] io
PCI: 00:0e.0 10 * [0x1080 - 0x10ff] io
PCI: 00:07.1 20 * [0x1400 - 0x140f] io
PCI_DOMAIN: 0000 compute_resources_io: base: 1410 size: 1410 align: 12 gran: 0 limit: ffff done
PCI_DOMAIN: 0000 compute_resources_mem: base: 0 size: 0 align: 0 gran: 0 limit: ffffffff
PCI: 00:01.0 compute_resources_prefmem: base: 0 size: 0 align: 20 gran: 20 limit: ffffffff
PCI: 01:00.0 compute_resources_prefmem: base: 0 size: 0 align: 20 gran: 20 limit: ffffffffffffffff
PCI: 01:00.0 compute_resources_prefmem: base: 0 size: 0 align: 20 gran: 20 limit: ffffffffffffffff done
PCI: 00:01.0 compute_resources_prefmem: base: 0 size: 0 align: 20 gran: 20 limit: ffffffff done
PCI: 00:01.0 compute_resources_mem: base: 0 size: 0 align: 20 gran: 20 limit: ffffffff
PCI: 01:00.0 compute_resources_mem: base: 0 size: 0 align: 20 gran: 20 limit: ffffffff
PCI: 02:04.0 30 * [0x0 - 0x3ffff] mem
PCI: 02:05.0 30 * [0x40000 - 0x7ffff] mem
PCI: 02:04.0 14 * [0x80000 - 0x803ff] mem
PCI: 02:05.0 14 * [0x80400 - 0x807ff] mem
PCI: 01:00.0 compute_resources_mem: base: 80800 size: 100000 align: 20 gran: 20 limit: ffffffff done
PCI: 01:00.0 20 * [0x0 - 0xfffff] mem
PCI: 00:01.0 compute_resources_mem: base: 100000 size: 100000 align: 20 gran: 20 limit: ffffffff done
PCI: 00:00.0 10 * [0x0 - 0xfffffff] prefmem
PCI: 00:01.0 20 * [0x10000000 - 0x100fffff] mem
PCI: 00:0d.0 30 * [0x10100000 - 0x1013ffff] mem
PCI: 00:0e.0 30 * [0x10140000 - 0x1017ffff] mem
PCI: 00:0d.0 14 * [0x10180000 - 0x101803ff] mem
PCI: 00:0e.0 14 * [0x10180400 - 0x101807ff] mem
PCI_DOMAIN: 0000 compute_resources_mem: base: 10180800 size: 10180800 align: 28 gran: 0 limit: ffffffff done
avoid_fixed_resources: PCI_DOMAIN: 0000
avoid_fixed_resources:@PCI_DOMAIN: 0000 10000000 limit 0000ffff
avoid_fixed_resources:@PCI_DOMAIN: 0000 10000100 limit ffffffff
constrain_resources: PCI_DOMAIN: 0000
constrain_resources: PCI: 00:00.0
constrain_resources: PCI: 00:01.0
constrain_resources: PCI: 01:00.0
constrain_resources: PCI: 02:04.0
constrain_resources: PCI: 02:05.0
constrain_resources: PCI: 00:07.0
constrain_resources: PNP: 03f0.4
constrain_resources: PNP: 03f0.5
constrain_resources: PNP: 03f0.7
constrain_resources: PNP: 03f0.6
constrain_resources: PNP: 03f0.8
constrain_resources: PCI: 00:07.1
constrain_resources: PCI: 00:0d.0
constrain_resources: PCI: 00:0e.0
constrain_resources: PCI: 00:0f.0
constrain_resources: PCI: 00:0f.1
avoid_fixed_resources2: PCI_DOMAIN: 0...@10000000 limit 0000ffff
lim->base 00001000 lim->limit 0000ffff
avoid_fixed_resources2: PCI_DOMAIN: 0...@10000100 limit ffffffff
lim->base 00000000 lim->limit febfffff
Setting resources...
PCI_DOMAIN: 0000 allocate_resources_io: base:1000 size:1410 align:12 gran:0 limit:ffff
Assigned: PCI: 00:01.0 1c * [0x1000 - 0x1fff] io
Assigned: PCI: 00:0d.0 10 * [0x2000 - 0x207f] io
Assigned: PCI: 00:0e.0 10 * [0x2080 - 0x20ff] io
Assigned: PCI: 00:07.1 20 * [0x2400 - 0x240f] io
PCI_DOMAIN: 0000 allocate_resources_io: next_base: 2410 size: 1410 align: 12 gran: 0 done
PCI: 00:01.0 allocate_resources_io: base:1000 size:1000 align:12 gran:12 limit:ffff
Assigned: PCI: 01:00.0 1c * [0x1000 - 0x1fff] io
PCI: 00:01.0 allocate_resources_io: next_base: 2000 size: 1000 align: 12 gran: 12 done
PCI: 01:00.0 allocate_resources_io: base:1000 size:1000 align:12 gran:12 limit:ffff
Assigned: PCI: 02:04.0 10 * [0x1000 - 0x107f] io
Assigned: PCI: 02:05.0 10 * [0x1080 - 0x10ff] io
PCI: 01:00.0 allocate_resources_io: next_base: 1100 size: 1000 align: 12 gran: 12 done
PCI_DOMAIN: 0000 allocate_resources_mem: base:e0000000 size:10180800 align:28 gran:0 limit:febfffff
Assigned: PCI: 00:00.0 10 * [0xe0000000 - 0xefffffff] prefmem
Assigned: PCI: 00:01.0 20 * [0xf0000000 - 0xf00fffff] mem
Assigned: PCI: 00:0d.0 30 * [0xf0100000 - 0xf013ffff] mem
Assigned: PCI: 00:0e.0 30 * [0xf0140000 - 0xf017ffff] mem
Assigned: PCI: 00:0d.0 14 * [0xf0180000 - 0xf01803ff] mem
Assigned: PCI: 00:0e.0 14 * [0xf0180400 - 0xf01807ff] mem
PCI_DOMAIN: 0000 allocate_resources_mem: next_base: f0180800 size: 10180800 align: 28 gran: 0 done
PCI: 00:01.0 allocate_resources_prefmem: base:febfffff size:0 align:20 gran:20 limit:febfffff
PCI: 00:01.0 allocate_resources_prefmem: next_base: febfffff size: 0 align: 20 gran: 20 done
PCI: 01:00.0 allocate_resources_prefmem: base:febfffff size:0 align:20 gran:20 limit:febfffff
PCI: 01:00.0 allocate_resources_prefmem: next_base: febfffff size: 0 align: 20 gran: 20 done
PCI: 00:01.0 allocate_resources_mem: base:f0000000 size:100000 align:20 gran:20 limit:febfffff
Assigned: PCI: 01:00.0 20 * [0xf0000000 - 0xf00fffff] mem
PCI: 00:01.0 allocate_resources_mem: next_base: f0100000 size: 100000 align: 20 gran: 20 done
PCI: 01:00.0 allocate_resources_mem: base:f0000000 size:100000 align:20 gran:20 limit:febfffff
Assigned: PCI: 02:04.0 30 * [0xf0000000 - 0xf003ffff] mem
Assigned: PCI: 02:05.0 30 * [0xf0040000 - 0xf007ffff] mem
Assigned: PCI: 02:04.0 14 * [0xf0080000 - 0xf00803ff] mem
Assigned: PCI: 02:05.0 14 * [0xf0080400 - 0xf00807ff] mem
PCI: 01:00.0 allocate_resources_mem: next_base: f0080800 size: 100000 align: 20 gran: 20 done
Root Device assign_resources, bus 0 link: 0
Setting RAM size to 512 MB
PCI_DOMAIN: 0000 assign_resources, bus 0 link: 0
PCI: 00:00.0 10 <- [0x00e0000000 - 0x00efffffff] size 0x10000000 gran 0x1c prefmem
PCI: 00:01.0 1c <- [0x0000001000 - 0x0000001fff] size 0x00001000 gran 0x0c bus 01 io
PCI: 00:01.0 24 <- [0x00febfffff - 0x00febffffe] size 0x00000000 gran 0x14 bus 01 prefmem
PCI: 00:01.0 20 <- [0x00f0000000 - 0x00f00fffff] size 0x00100000 gran 0x14 bus 01 mem
PCI: 00:01.0 assign_resources, bus 1 link: 0
PCI: 01:00.0 1c <- [0x0000001000 - 0x0000001fff] size 0x00001000 gran 0x0c bus 02 io
PCI: 01:00.0 24 <- [0x00febfffff - 0x00febffffe] size 0x00000000 gran 0x14 bus 02 prefmem
PCI: 01:00.0 20 <- [0x00f0000000 - 0x00f00fffff] size 0x00100000 gran 0x14 bus 02 mem
PCI: 01:00.0 assign_resources, bus 2 link: 0
PCI: 02:04.0 10 <- [0x0000001000 - 0x000000107f] size 0x00000080 gran 0x07 io
PCI: 02:04.0 14 <- [0x00f0080000 - 0x00f00803ff] size 0x00000400 gran 0x0a mem
PCI: 02:04.0 30 <- [0x00f0000000 - 0x00f003ffff] size 0x00040000 gran 0x12 romem
PCI: 02:05.0 10 <- [0x0000001080 - 0x00000010ff] size 0x00000080 gran 0x07 io
PCI: 02:05.0 14 <- [0x00f0080400 - 0x00f00807ff] size 0x00000400 gran 0x0a mem
PCI: 02:05.0 30 <- [0x00f0040000 - 0x00f007ffff] size 0x00040000 gran 0x12 romem
PCI: 01:00.0 assign_resources, bus 2 link: 0
PCI: 00:01.0 assign_resources, bus 1 link: 0
PCI: 00:07.0 assign_resources, bus 0 link: 0
PNP: 03f0.4 60 <- [0x00000003f8 - 0x00000003ff] size 0x00000008 gran 0x03 io
PNP: 03f0.4 70 <- [0x0000000004 - 0x0000000004] size 0x00000001 gran 0x00 irq
PNP: 03f0.5 60 <- [0x00000002f8 - 0x00000002ff] size 0x00000008 gran 0x03 io
PNP: 03f0.5 70 <- [0x0000000003 - 0x0000000003] size 0x00000001 gran 0x00 irq
ERROR: PNP: 03f0.7 60 io size: 0x0000000001 not assigned
ERROR: PNP: 03f0.7 62 io size: 0x0000000001 not assigned
ERROR: PNP: 03f0.7 70 irq size: 0x0000000001 not assigned
ERROR: PNP: 03f0.7 72 irq size: 0x0000000001 not assigned
PCI: 00:07.0 assign_resources, bus 0 link: 0
PCI: 00:07.1 20 <- [0x0000002400 - 0x000000240f] size 0x00000010 gran 0x04 io
PCI: 00:0d.0 10 <- [0x0000002000 - 0x000000207f] size 0x00000080 gran 0x07 io
PCI: 00:0d.0 14 <- [0x00f0180000 - 0x00f01803ff] size 0x00000400 gran 0x0a mem
PCI: 00:0d.0 30 <- [0x00f0100000 - 0x00f013ffff] size 0x00040000 gran 0x12 romem
PCI: 00:0e.0 10 <- [0x0000002080 - 0x00000020ff] size 0x00000080 gran 0x07 io
PCI: 00:0e.0 14 <- [0x00f0180400 - 0x00f01807ff] size 0x00000400 gran 0x0a mem
PCI: 00:0e.0 30 <- [0x00f0140000 - 0x00f017ffff] size 0x00040000 gran 0x12 romem
PCI_DOMAIN: 0000 assign_resources, bus 0 link: 0
Root Device assign_resources, bus 0 link: 0
Done setting resources.
Show resources in subtree (Root Device)...After assigning values.
Root Device child on link 0 APIC_CLUSTER: 0
APIC_CLUSTER: 0 child on link 0 APIC: 00
APIC: 00
PCI_DOMAIN: 0000 child on link 0 PCI: 00:00.0
PCI_DOMAIN: 0000 resource base 1000 size 1410 align 12 gran 0 limit ffff flags 40040100 index 10000000
PCI_DOMAIN: 0000 resource base e0000000 size 10180800 align 28 gran 0 limit febfffff flags 40040200 index 10000100
PCI_DOMAIN: 0000 resource base 0 size a0000 align 0 gran 0 limit 0 flags e0004200 index a
PCI_DOMAIN: 0000 resource base c0000 size 1ff40000 align 0 gran 0 limit 0 flags e0004200 index b
PCI: 00:00.0
PCI: 00:00.0 resource base e0000000 size 10000000 align 28 gran 28 limit febfffff flags 60001200 index 10
PCI: 00:01.0 child on link 0 PCI: 01:00.0
PCI: 00:01.0 resource base 1000 size 1000 align 12 gran 12 limit ffff flags 60080102 index 1c
PCI: 00:01.0 resource base febfffff size 0 align 20 gran 20 limit febfffff flags 60081202 index 24
PCI: 00:01.0 resource base f0000000 size 100000 align 20 gran 20 limit febfffff flags 60080202 index 20
PCI: 01:00.0 child on link 0 PCI: 02:04.0
PCI: 01:00.0 resource base 1000 size 1000 align 12 gran 12 limit ffff flags 60080102 index 1c
PCI: 01:00.0 resource base febfffff size 0 align 20 gran 20 limit febfffff flags 60081202 index 24
PCI: 01:00.0 resource base f0000000 size 100000 align 20 gran 20 limit febfffff flags 60080202 index 20
PCI: 02:04.0
PCI: 02:04.0 resource base 1000 size 80 align 7 gran 7 limit ffff flags 60000100 index 10
PCI: 02:04.0 resource base f0080000 size 400 align 10 gran 10 limit febfffff flags 60000200 index 14
PCI: 02:04.0 resource base f0000000 size 40000 align 18 gran 18 limit febfffff flags 60002200 index 30
PCI: 02:05.0
PCI: 02:05.0 resource base 1080 size 80 align 7 gran 7 limit ffff flags 60000100 index 10
PCI: 02:05.0 resource base f0080400 size 400 align 10 gran 10 limit febfffff flags 60000200 index 14
PCI: 02:05.0 resource base f0040000 size 40000 align 18 gran 18 limit febfffff flags 60002200 index 30
PCI: 00:07.0 child on link 0 PNP: 03f0.0
PCI: 00:07.0 resource base 0 size 1000 align 0 gran 0 limit ffff flags c0000100 index 1
PCI: 00:07.0 resource base ff800000 size 800000 align 0 gran 0 limit 0 flags c0000200 index 2
PCI: 00:07.0 resource base fec00000 size 1000 align 0 gran 0 limit 0 flags c0000200 index 3
PNP: 03f0.0
PNP: 03f0.0 resource base 0 size 8 align 3 gran 3 limit 7ff flags 100 index 60
PNP: 03f0.0 resource base 0 size 1 align 0 gran 0 limit 0 flags 400 index 70
PNP: 03f0.0 resource base 0 size 1 align 0 gran 0 limit 0 flags 800 index 74
PNP: 03f0.3
PNP: 03f0.3 resource base 0 size 8 align 3 gran 3 limit 7ff flags 100 index 60
PNP: 03f0.3 resource base 0 size 1 align 0 gran 0 limit 0 flags 400 index 70
PNP: 03f0.3 resource base 0 size 1 align 0 gran 0 limit 0 flags 800 index 74
PNP: 03f0.4
PNP: 03f0.4 resource base 3f8 size 8 align 3 gran 3 limit 7ff flags e0000100 index 60
PNP: 03f0.4 resource base 4 size 1 align 0 gran 0 limit 0 flags e0000400 index 70
PNP: 03f0.5
PNP: 03f0.5 resource base 2f8 size 8 align 3 gran 3 limit 7ff flags e0000100 index 60
PNP: 03f0.5 resource base 3 size 1 align 0 gran 0 limit 0 flags e0000400 index 70
PNP: 03f0.7
PNP: 03f0.7 resource base 0 size 1 align 0 gran 0 limit ffffffff flags 100 index 60
PNP: 03f0.7 resource base 0 size 1 align 0 gran 0 limit ffffffff flags 100 index 62
PNP: 03f0.7 resource base 0 size 1 align 0 gran 0 limit 0 flags 400 index 70
PNP: 03f0.7 resource base 0 size 1 align 0 gran 0 limit 0 flags 400 index 72
PNP: 03f0.6
PNP: 03f0.8
PNP: 03f0.a
PCI: 00:07.1
PCI: 00:07.1 resource base 2400 size 10 align 4 gran 4 limit ffff flags 60000100 index 20
PCI: 00:07.2
PCI: 00:07.3
PCI: 00:0d.0
PCI: 00:0d.0 resource base 2000 size 80 align 7 gran 7 limit ffff flags 60000100 index 10
PCI: 00:0d.0 resource base f0180000 size 400 align 10 gran 10 limit febfffff flags 60000200 index 14
PCI: 00:0d.0 resource base f0100000 size 40000 align 18 gran 18 limit febfffff flags 60002200 index 30
PCI: 00:0e.0
PCI: 00:0e.0 resource base 2080 size 80 align 7 gran 7 limit ffff flags 60000100 index 10
PCI: 00:0e.0 resource base f0180400 size 400 align 10 gran 10 limit febfffff flags 60000200 index 14
PCI: 00:0e.0 resource base f0140000 size 40000 align 18 gran 18 limit febfffff flags 60002200 index 30
PCI: 00:0f.0
PCI: 00:0f.1
Done allocating resources.
POST: 0x88
Enabling resources...
PCI: 00:00.0 cmd <- 06
PCI: 00:01.0 bridge ctrl <- 0083
PCI: 00:01.0 cmd <- 07
PCI: 01:00.0 bridge ctrl <- 0003
PCI: 01:00.0 cmd <- 07
PCI: 02:04.0 cmd <- 03
PCI: 02:05.0 cmd <- 03
PCI: 00:07.0 cmd <- 07
PCI: 00:07.1 cmd <- 01
PCI: 00:0d.0 cmd <- 03
PCI: 00:0e.0 cmd <- 03
PCI: 00:0f.0 cmd <- 00
PCI: 00:0f.1 cmd <- 00
done.
Initializing devices...
Root Device init
APIC_CLUSTER: 0 init
Initializing CPU #0
CPU: vendor Intel device 68a
CPU: family 06, model 08, stepping 0a
Using generic cpu ops (good)
POST: 0x60
Enabling cache
Setting fixed MTRRs(0-88) Type: UC
Setting fixed MTRRs(0-16) Type: WB
Setting fixed MTRRs(24-88) Type: WB
DONE fixed MTRRs
call enable_fixed_mtrr()
Setting variable MTRR 0, base: 0MB, range: 512MB, type WB
ADDRESS_MASK_HIGH=0xf
Zero-sized MTRR range @0KB
DONE variable MTRRs
Clear out the extra MTRR's
call enable_var_mtrr()
Leave x86_setup_var_mtrrs
POST: 0x6a
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
POST: 0x93
microcode_info: sig = 0x0000068a pf=0x00000010 rev = 0x00000000
Setting up local apic... apic_id: 0x00 done.
POST: 0x9b
CPU #0 initialized
PCI: 00:00.0 init
Northbridge Init
PCI: 00:07.0 init
RTC Init
PNP: 03f0.4 init
PNP: 03f0.5 init
PNP: 03f0.7 init
Keyboard init...
No PS/2 keyboard detected.
PNP: 03f0.6 init
PNP: 03f0.8 init
PCI: 00:07.1 init
IDE: Primary IDE interface: on
IDE: Secondary IDE interface: on
IDE: Access to legacy IDE ports: on
IDE: Primary IDE interface, drive 0: UDMA/33: on
IDE: Primary IDE interface, drive 1: UDMA/33: on
IDE: Secondary IDE interface, drive 0: UDMA/33: on
IDE: Secondary IDE interface, drive 1: UDMA/33: on
PCI: 00:0d.0 init
Init of DECchip 21143 Kconfig style
0x04 = 02800107 (07 01 80 02)
0x0c = 00004000 (00 80 00 00)
0x30 = 00000000 (0x00000000)
PCI: 00:0e.0 init
Init of DECchip 21143 Kconfig style
0x04 = 02800107 (07 01 80 02)
0x0c = 00004000 (00 80 00 00)
0x30 = 00000000 (0x00000000)
PCI: 00:0f.0 init
Init of Texas Instruments PCI1x2x PCMCIA/CardBus controller
PCI: 00:0f.1 init
Init of Texas Instruments PCI1x2x PCMCIA/CardBus controller
PCI: 02:04.0 init
Init of DECchip 21143 Kconfig style
0x04 = 02800107 (07 01 80 02)
0x0c = 00004000 (00 80 00 00)
0x30 = 00000000 (0x00000000)
PCI: 02:05.0 init
Init of DECchip 21143 Kconfig style
0x04 = 02800107 (07 01 80 02)
0x0c = 00004000 (00 80 00 00)
0x30 = 00000000 (0x00000000)
Devices initialized
Show all devs...After init.
Root Device: enabled 1
APIC_CLUSTER: 0: enabled 1
APIC: 00: enabled 1
PCI_DOMAIN: 0000: enabled 1
PCI: 00:00.0: enabled 1
PCI: 00:01.0: enabled 1
PCI: 00:07.0: enabled 1
PNP: 03f0.0: enabled 0
PNP: 03f0.3: enabled 0
PNP: 03f0.4: enabled 1
PNP: 03f0.5: enabled 1
PNP: 03f0.7: enabled 1
PNP: 03f0.6: enabled 1
PNP: 03f0.8: enabled 1
PNP: 03f0.a: enabled 0
PCI: 00:07.1: enabled 1
PCI: 00:07.2: enabled 0
PCI: 00:07.3: enabled 0
PCI: 00:0d.0: enabled 1
PCI: 00:0e.0: enabled 1
PCI: 00:0f.0: enabled 1
PCI: 00:0f.1: enabled 1
PCI: 01:00.0: enabled 1
PCI: 02:04.0: enabled 1
PCI: 02:05.0: enabled 1
POST: 0x89
Initializing CBMEM area to 0x1fff0000 (65536 bytes)
Adding CBMEM entry as no. 1
Moving GDT to 1fff0200...ok
High Tables Base is 1fff0000.
POST: 0x9a
Copying Interrupt Routing Table to 0x000f0000... done.
Verifying copy of Interrupt Routing Table at 0x000f0000... done
Checking Interrupt Routing Table consistency...
check_pirq_routing_table(): Interrupt Routing Table located at 000f0000.
done.
PIRQ Entry 0 Dev/Fn: 7 Slot: 0
INT: A link: 0 bitmap: 1e20 not routed
INT: B link: 0 bitmap: 1e20 not routed
INT: C link: 0 bitmap: 1e20 not routed
INT: D link: 63 bitmap: 1e20 not routed
Assigning IRQ 0 to 0:7.2
i8259_configure_irq_trigger: current interrupts are 0x0
i8259_configure_irq_trigger: try to set interrupts 0x1
PIRQ Entry 1 Dev/Fn: 0 Slot: 0
INT: A link: 60 bitmap: 1e20 not routed
INT: B link: 61 bitmap: 1e20 not routed
INT: C link: 62 bitmap: 1e20 not routed
INT: D link: 63 bitmap: 1e20 not routed
PIRQ Entry 2 Dev/Fn: D Slot: 0
INT: A link: 62 bitmap: 1e20 not routed
INT: B link: 0 bitmap: 1e20 not routed
INT: C link: 0 bitmap: 1e20 not routed
INT: D link: 0 bitmap: 1e20 not routed
Assigning IRQ 0 to 0:d.0
i8259_configure_irq_trigger: current interrupts are 0x0
i8259_configure_irq_trigger: try to set interrupts 0x1
PIRQ Entry 3 Dev/Fn: E Slot: 0
INT: A link: 63 bitmap: 1e20 not routed
INT: B link: 0 bitmap: 1e20 not routed
INT: C link: 0 bitmap: 1e20 not routed
INT: D link: 0 bitmap: 1e20 not routed
Assigning IRQ 0 to 0:e.0
i8259_configure_irq_trigger: current interrupts are 0x0
i8259_configure_irq_trigger: try to set interrupts 0x1
PIRQ Entry 4 Dev/Fn: 4 Slot: 0
INT: A link: 60 bitmap: 1e20 not routed
INT: B link: 0 bitmap: 1e20 not routed
INT: C link: 0 bitmap: 1e20 not routed
INT: D link: 0 bitmap: 1e20 not routed
Assigning IRQ 0 to 2:4.0
i8259_configure_irq_trigger: current interrupts are 0x0
i8259_configure_irq_trigger: try to set interrupts 0x1
PIRQ Entry 5 Dev/Fn: 5 Slot: 0
INT: A link: 61 bitmap: 1e20 not routed
INT: B link: 0 bitmap: 1e20 not routed
INT: C link: 0 bitmap: 1e20 not routed
INT: D link: 0 bitmap: 1e20 not routed
Assigning IRQ 0 to 2:5.0
i8259_configure_irq_trigger: current interrupts are 0x0
i8259_configure_irq_trigger: try to set interrupts 0x1
PIRQ Entry 6 Dev/Fn: F Slot: 0
INT: A link: 60 bitmap: 1e20 not routed
INT: B link: 61 bitmap: 1e20 not routed
INT: C link: 0 bitmap: 1e20 not routed
INT: D link: 0 bitmap: 1e20 not routed
Assigning IRQ 0 to 0:f.0
i8259_configure_irq_trigger: current interrupts are 0x0
i8259_configure_irq_trigger: try to set interrupts 0x1
Assigning IRQ 0 to 0:f.1
i8259_configure_irq_trigger: current interrupts are 0x0
i8259_configure_irq_trigger: try to set interrupts 0x1
PIRQ Entry 7 Dev/Fn: 7 Slot: 0
INT: A link: 61 bitmap: 1e20 not routed
INT: B link: 62 bitmap: 1e20 not routed
INT: C link: 63 bitmap: 1e20 not routed
INT: D link: 64 bitmap: 1e20 not routed
PIRQ Entry 8 Dev/Fn: 4 Slot: 1
INT: A link: 61 bitmap: 1e20 not routed
INT: B link: 62 bitmap: 1e20 not routed
INT: C link: 63 bitmap: 1e20 not routed
INT: D link: 60 bitmap: 1e20 not routed
PIRQ Entry 9 Dev/Fn: 5 Slot: 2
INT: A link: 62 bitmap: 1e20 not routed
INT: B link: 63 bitmap: 1e20 not routed
INT: C link: 60 bitmap: 1e20 not routed
INT: D link: 61 bitmap: 1e20 not routed
PIRQ Entry 10 Dev/Fn: 6 Slot: 3
INT: A link: 63 bitmap: 1e20 not routed
INT: B link: 60 bitmap: 1e20 not routed
INT: C link: 61 bitmap: 1e20 not routed
INT: D link: 62 bitmap: 1e20 not routed
PIRQ Entry 11 Dev/Fn: 7 Slot: 4
INT: A link: 60 bitmap: 1e20 not routed
INT: B link: 61 bitmap: 1e20 not routed
INT: C link: 62 bitmap: 1e20 not routed
INT: D link: 63 bitmap: 1e20 not routed
PIRQ Entry 12 Dev/Fn: 6 Slot: 0
INT: A link: 61 bitmap: 1e20 not routed
INT: B link: 62 bitmap: 1e20 not routed
INT: C link: 63 bitmap: 1e20 not routed
INT: D link: 60 bitmap: 1e20 not routed
PIRQ Entry 13 Dev/Fn: 4 Slot: 5
INT: A link: 61 bitmap: 1e20 not routed
INT: B link: 62 bitmap: 1e20 not routed
INT: C link: 63 bitmap: 1e20 not routed
INT: D link: 60 bitmap: 1e20 not routed
PIRQ Entry 14 Dev/Fn: 5 Slot: 6
INT: A link: 62 bitmap: 1e20 not routed
INT: B link: 63 bitmap: 1e20 not routed
INT: C link: 60 bitmap: 1e20 not routed
INT: D link: 61 bitmap: 1e20 not routed
PIRQ Entry 15 Dev/Fn: 6 Slot: 7
INT: A link: 63 bitmap: 1e20 not routed
INT: B link: 60 bitmap: 1e20 not routed
INT: C link: 61 bitmap: 1e20 not routed
INT: D link: 62 bitmap: 1e20 not routed
PIRQ Entry 16 Dev/Fn: 7 Slot: 8
INT: A link: 60 bitmap: 1e20 not routed
INT: B link: 61 bitmap: 1e20 not routed
INT: C link: 62 bitmap: 1e20 not routed
INT: D link: 63 bitmap: 1e20 not routed
PIRQ Entry 17 Dev/Fn: 10 Slot: 0
INT: A link: 61 bitmap: 1e20 not routed
INT: B link: 62 bitmap: 1e20 not routed
INT: C link: 63 bitmap: 1e20 not routed
INT: D link: 60 bitmap: 1e20 not routed
PIRQ Entry 18 Dev/Fn: 4 Slot: 9
INT: A link: 61 bitmap: 1e20 not routed
INT: B link: 62 bitmap: 1e20 not routed
INT: C link: 63 bitmap: 1e20 not routed
INT: D link: 60 bitmap: 1e20 not routed
PIRQ Entry 19 Dev/Fn: 5 Slot: 10
INT: A link: 62 bitmap: 1e20 not routed
INT: B link: 63 bitmap: 1e20 not routed
INT: C link: 60 bitmap: 1e20 not routed
INT: D link: 61 bitmap: 1e20 not routed
PIRQ Entry 20 Dev/Fn: 6 Slot: 11
INT: A link: 63 bitmap: 1e20 not routed
INT: B link: 60 bitmap: 1e20 not routed
INT: C link: 61 bitmap: 1e20 not routed
INT: D link: 62 bitmap: 1e20 not routed
PIRQ Entry 21 Dev/Fn: 7 Slot: 12
INT: A link: 60 bitmap: 1e20 not routed
INT: B link: 61 bitmap: 1e20 not routed
INT: C link: 62 bitmap: 1e20 not routed
INT: D link: 63 bitmap: 1e20 not routed
PIRQ1: 0
PIRQ2: 0
PIRQ3: 0
PIRQ4: 0
Adding CBMEM entry as no. 2
Copying Interrupt Routing Table to 0x1fff0400... done.
Verifying copy of Interrupt Routing Table at 0x1fff0400... done
Checking Interrupt Routing Table consistency...
check_pirq_routing_table(): Interrupt Routing Table located at 1fff0400.
done.
PIRQ Entry 0 Dev/Fn: 7 Slot: 0
INT: A link: 0 bitmap: 1e20 not routed
INT: B link: 0 bitmap: 1e20 not routed
INT: C link: 0 bitmap: 1e20 not routed
INT: D link: 63 bitmap: 1e20 not routed
Assigning IRQ 0 to 0:7.2
i8259_configure_irq_trigger: current interrupts are 0x0
i8259_configure_irq_trigger: try to set interrupts 0x1
PIRQ Entry 1 Dev/Fn: 0 Slot: 0
INT: A link: 60 bitmap: 1e20 not routed
INT: B link: 61 bitmap: 1e20 not routed
INT: C link: 62 bitmap: 1e20 not routed
INT: D link: 63 bitmap: 1e20 not routed
PIRQ Entry 2 Dev/Fn: D Slot: 0
INT: A link: 62 bitmap: 1e20 not routed
INT: B link: 0 bitmap: 1e20 not routed
INT: C link: 0 bitmap: 1e20 not routed
INT: D link: 0 bitmap: 1e20 not routed
Assigning IRQ 0 to 0:d.0
i8259_configure_irq_trigger: current interrupts are 0x0
i8259_configure_irq_trigger: try to set interrupts 0x1
PIRQ Entry 3 Dev/Fn: E Slot: 0
INT: A link: 63 bitmap: 1e20 not routed
INT: B link: 0 bitmap: 1e20 not routed
INT: C link: 0 bitmap: 1e20 not routed
INT: D link: 0 bitmap: 1e20 not routed
Assigning IRQ 0 to 0:e.0
i8259_configure_irq_trigger: current interrupts are 0x0
i8259_configure_irq_trigger: try to set interrupts 0x1
PIRQ Entry 4 Dev/Fn: 4 Slot: 0
INT: A link: 60 bitmap: 1e20 not routed
INT: B link: 0 bitmap: 1e20 not routed
INT: C link: 0 bitmap: 1e20 not routed
INT: D link: 0 bitmap: 1e20 not routed
Assigning IRQ 0 to 2:4.0
i8259_configure_irq_trigger: current interrupts are 0x0
i8259_configure_irq_trigger: try to set interrupts 0x1
PIRQ Entry 5 Dev/Fn: 5 Slot: 0
INT: A link: 61 bitmap: 1e20 not routed
INT: B link: 0 bitmap: 1e20 not routed
INT: C link: 0 bitmap: 1e20 not routed
INT: D link: 0 bitmap: 1e20 not routed
Assigning IRQ 0 to 2:5.0
i8259_configure_irq_trigger: current interrupts are 0x0
i8259_configure_irq_trigger: try to set interrupts 0x1
PIRQ Entry 6 Dev/Fn: F Slot: 0
INT: A link: 60 bitmap: 1e20 not routed
INT: B link: 61 bitmap: 1e20 not routed
INT: C link: 0 bitmap: 1e20 not routed
INT: D link: 0 bitmap: 1e20 not routed
Assigning IRQ 0 to 0:f.0
i8259_configure_irq_trigger: current interrupts are 0x0
i8259_configure_irq_trigger: try to set interrupts 0x1
Assigning IRQ 0 to 0:f.1
i8259_configure_irq_trigger: current interrupts are 0x0
i8259_configure_irq_trigger: try to set interrupts 0x1
PIRQ Entry 7 Dev/Fn: 7 Slot: 0
INT: A link: 61 bitmap: 1e20 not routed
INT: B link: 62 bitmap: 1e20 not routed
INT: C link: 63 bitmap: 1e20 not routed
INT: D link: 64 bitmap: 1e20 not routed
PIRQ Entry 8 Dev/Fn: 4 Slot: 1
INT: A link: 61 bitmap: 1e20 not routed
INT: B link: 62 bitmap: 1e20 not routed
INT: C link: 63 bitmap: 1e20 not routed
INT: D link: 60 bitmap: 1e20 not routed
PIRQ Entry 9 Dev/Fn: 5 Slot: 2
INT: A link: 62 bitmap: 1e20 not routed
INT: B link: 63 bitmap: 1e20 not routed
INT: C link: 60 bitmap: 1e20 not routed
INT: D link: 61 bitmap: 1e20 not routed
PIRQ Entry 10 Dev/Fn: 6 Slot: 3
INT: A link: 63 bitmap: 1e20 not routed
INT: B link: 60 bitmap: 1e20 not routed
INT: C link: 61 bitmap: 1e20 not routed
INT: D link: 62 bitmap: 1e20 not routed
PIRQ Entry 11 Dev/Fn: 7 Slot: 4
INT: A link: 60 bitmap: 1e20 not routed
INT: B link: 61 bitmap: 1e20 not routed
INT: C link: 62 bitmap: 1e20 not routed
INT: D link: 63 bitmap: 1e20 not routed
PIRQ Entry 12 Dev/Fn: 6 Slot: 0
INT: A link: 61 bitmap: 1e20 not routed
INT: B link: 62 bitmap: 1e20 not routed
INT: C link: 63 bitmap: 1e20 not routed
INT: D link: 60 bitmap: 1e20 not routed
PIRQ Entry 13 Dev/Fn: 4 Slot: 5
INT: A link: 61 bitmap: 1e20 not routed
INT: B link: 62 bitmap: 1e20 not routed
INT: C link: 63 bitmap: 1e20 not routed
INT: D link: 60 bitmap: 1e20 not routed
PIRQ Entry 14 Dev/Fn: 5 Slot: 6
INT: A link: 62 bitmap: 1e20 not routed
INT: B link: 63 bitmap: 1e20 not routed
INT: C link: 60 bitmap: 1e20 not routed
INT: D link: 61 bitmap: 1e20 not routed
PIRQ Entry 15 Dev/Fn: 6 Slot: 7
INT: A link: 63 bitmap: 1e20 not routed
INT: B link: 60 bitmap: 1e20 not routed
INT: C link: 61 bitmap: 1e20 not routed
INT: D link: 62 bitmap: 1e20 not routed
PIRQ Entry 16 Dev/Fn: 7 Slot: 8
INT: A link: 60 bitmap: 1e20 not routed
INT: B link: 61 bitmap: 1e20 not routed
INT: C link: 62 bitmap: 1e20 not routed
INT: D link: 63 bitmap: 1e20 not routed
PIRQ Entry 17 Dev/Fn: 10 Slot: 0
INT: A link: 61 bitmap: 1e20 not routed
INT: B link: 62 bitmap: 1e20 not routed
INT: C link: 63 bitmap: 1e20 not routed
INT: D link: 60 bitmap: 1e20 not routed
PIRQ Entry 18 Dev/Fn: 4 Slot: 9
INT: A link: 61 bitmap: 1e20 not routed
INT: B link: 62 bitmap: 1e20 not routed
INT: C link: 63 bitmap: 1e20 not routed
INT: D link: 60 bitmap: 1e20 not routed
PIRQ Entry 19 Dev/Fn: 5 Slot: 10
INT: A link: 62 bitmap: 1e20 not routed
INT: B link: 63 bitmap: 1e20 not routed
INT: C link: 60 bitmap: 1e20 not routed
INT: D link: 61 bitmap: 1e20 not routed
PIRQ Entry 20 Dev/Fn: 6 Slot: 11
INT: A link: 63 bitmap: 1e20 not routed
INT: B link: 60 bitmap: 1e20 not routed
INT: C link: 61 bitmap: 1e20 not routed
INT: D link: 62 bitmap: 1e20 not routed
PIRQ Entry 21 Dev/Fn: 7 Slot: 12
INT: A link: 60 bitmap: 1e20 not routed
INT: B link: 61 bitmap: 1e20 not routed
INT: C link: 62 bitmap: 1e20 not routed
INT: D link: 63 bitmap: 1e20 not routed
PIRQ1: 0
PIRQ2: 0
PIRQ3: 0
PIRQ4: 0
PIRQ table: 384 bytes.
POST: 0x9d
Multiboot Information structure has been written.
POST: 0x9d
Adding CBMEM entry as no. 3
Writing high table forward entry at 0x00000500
Wrote coreboot table at: 00000500 - 00000518 checksum cbdf
New low_table_end: 0x00000518
Now going to write high coreboot table at 0x1fff1400
rom_table_end = 0x1fff1400
Adjust low_table_end from 0x00000518 to 0x00001000
Adjust rom_table_end from 0x1fff1400 to 0x20000000
Adding high table area
coreboot memory table:
0. 0000000000000000-0000000000000fff: CONFIGURATION TABLES
1. 0000000000001000-000000000009ffff: RAM
2. 00000000000c0000-000000001ffeffff: RAM
3. 000000001fff0000-000000001fffffff: CONFIGURATION TABLES
Wrote coreboot table at: 1fff1400 - 1fff15a0 checksum fda9
coreboot table: 416 bytes.
POST: 0x9e
0. FREE SPACE 1fff3400 0000cc00
1. GDT 1fff0200 00000200
2. IRQ TABLE 1fff0400 00001000
3. COREBOOT 1fff1400 00002000
Check CBFS header at fffeffe0
magic is 4f524243
Found CBFS header at fffeffe0
Check fallback/coreboot_ram
CBFS: follow chain: fff80000 + 38 + 9f56 + align -> fff89fc0
Check fallback/payload
Got a payload
Loading segment from rom address 0xfff89ff8
data (compression=1)
malloc Enter, size 36, free_mem_ptr 00120c0c
malloc 00120c0c
New segment dstaddr 0xebc20 memsize 0x143e0 srcaddr 0xfff8a030 filesize 0xa1f2
(cleaned up) New segment addr 0xebc20 size 0x143e0 offset 0xfff8a030 filesize 0xa1f2
Loading segment from rom address 0xfff8a014
Entry Point 0x000fc8c8
Loading Segment: addr: 0x00000000000ebc20 memsz: 0x00000000000143e0 filesz: 0x000000000000a1f2
lb: [0x0000000000100000, 0x0000000000124000)
Post relocation: addr: 0x00000000000ebc20 memsz: 0x00000000000143e0 filesz: 0x000000000000a1f2
using LZMA
[ 0x000ebc20, 00100000, 0x00100000) <- fff8a030
dest 000ebc20, end 00100000, bouncebuffer 1ffa8000
Loaded segments
Jumping to boot code at fc8c8
POST: 0xfe
entry = 0x000fc8c8
lb_start = 0x00100000
lb_size = 0x00024000
adjust = 0x1fecc000
buffer = 0x1ffa8000
elf_boot_notes = 0x00112e48
adjusted_boot_notes = 0x1ffdee48
Start bios (version pre-0.6.1-20100613_092256-phong)
Found mainboard Nokia IP530
Found CBFS header at 0xfffeffe0
Ram Size=0x1fff0000 (0x0000000000000000 high)
CPU Mhz=721
Found 1 cpu(s) max supported 1 cpu(s)
Copying PIR from 0x1fff0400 to 0x000fdb70
SMBIOS ptr=0x000fdb50 table=0x1ffefef0
Scan for VGA option rom
UHCI init on dev 00:07.2 (io=0)
Found 0 lpt ports
Found 2 serial ports
ATA controller 0 at 1f0/3f4/0 (irq 14 dev 39)
ATA controller 1 at 170/374/0 (irq 15 dev 39)
Got ps2 nak (status=51)
ata0-0: WDC WD800JB-22JJC0 ATA-6 Hard-Disk (74 GiBytes)
drive 0x000fdb00: PCHS=16383/16/63 translation=lba LCHS=1024/255/63 s=156301488
All threads complete.
Scan for option roms
Press F12 for boot menu.
Returned 61440 bytes of ZoneHigh
e820 map has 5 items:
0: 0000000000000000 - 000000000009fc00 = 1
1: 000000000009fc00 - 00000000000a0000 = 2
2: 00000000000f0000 - 0000000000100000 = 2
3: 0000000000100000 - 000000001ffef000 = 1
4: 000000001ffef000 - 0000000020000000 = 2
enter handle_19:
NULL
Booting from Floppy...
Boot failed: could not read the boot disk
enter handle_18:
NULL
Booting from DVD/CD...
Boot failed: Could not read from CDROM (code 0001)
enter handle_18:
NULL
Booting from Hard Disk...
Booting from 0000:7c00
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-2-686 (Debian 2.6.26-22lenny1) ([email protected]) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Wed May 12 21:56:10 UTC 2010
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001ffef000 (usable)
[ 0.000000] BIOS-e820: 000000001ffef000 - 0000000020000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 511MB LOWMEM available.
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 131055
[ 0.000000] HighMem 131055 -> 131055
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 131055
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI Error (tbxfroot-0218): A valid RSDP was not found [20080321]
[ 0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:e0000000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] SMP: Allowing 0 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37992 bytes of per cpu data
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130031
[ 0.000000] Kernel command line: root=/dev/hda1 rw console=ttyS0,115200
[ 0.000000] Found and enabled local APIC!
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 721.094 MHz processor.
[ 0.004000] Console: colour dummy device 80x25
[ 0.004000] console [ttyS0] enabled
[ 0.004000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.004000] Memory: 509764k/524220k available (1771k kernel code, 13836k reserved, 750k data, 244k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xdffef000 ( 511 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02bad7d - 0xc0376620 ( 750 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02bad7d (1771 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.084397] Calibrating delay using timer specific routine.. 1444.02 BogoMIPS (lpj=2888041)
[ 0.092870] Security Framework initialized
[ 0.096982] SELinux: Disabled at boot.
[ 0.100828] Capability LSM initialized
[ 0.104623] Mount-cache hash table entries: 512
[ 0.109543] Initializing cgroup subsys ns
[ 0.113564] Initializing cgroup subsys cpuacct
[ 0.118012] Initializing cgroup subsys devices
[ 0.122505] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 0.127224] CPU: L2 cache: 256K
[ 0.130371] CPU serial number disabled.
[ 0.134215] Intel machine check architecture supported.
[ 0.139445] Intel machine check reporting enabled on CPU#0.
[ 0.144009] Checking 'hlt' instruction... OK.
[ 0.164010] SMP alternatives: switching to UP code
[ 0.180011] Freeing SMP alternatives: 16k freed
[ 0.184011] ACPI: Core revision 20080321
[ 0.188011] ACPI Exception (tbxface-0629): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20080321]
[ 0.196012] ACPI: Unable to load the System Description Tables
[ 0.200012] weird, boot CPU (#0) not listedby the BIOS.
[ 0.204012] SMP motherboard not detected.
[ 0.316019] SMP disabled
[ 0.316019] Brought up 1 CPUs
[ 0.318996] Total of 1 processors activated (1444.02 BogoMIPS).
[ 0.324369] net_namespace: 660 bytes
[ 0.327957] Booting paravirtualized kernel on bare hardware
[ 0.332020] NET: Registered protocol family 16
[ 0.336925] PCI: PCI BIOS revision 2.10 entry at 0xffe77, last bus=2
[ 0.343284] PCI: Using configuration type 1 for base access
[ 0.348021] Setting up standard PCI resources
[ 0.352022] ACPI: Interpreter disabled.
[ 0.355879] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.360022] pnp: PnP ACPI: disabled
[ 0.363516] PnPBIOS: Scanning system for PnP BIOS support...
[ 0.368023] PnPBIOS: Found PnP BIOS installation structure at 0xc00fd2f0
[ 0.372023] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc81d, dseg 0xf0000
pnp call arg1=0
[ 0.377538] PnPBIOS: dev_node_info: function not supported on this system
[ 0.384024] PnPBIOS: Unable to get node info. Aborting.
[ 0.388024] PCI: Probing PCI hardware
[ 0.392024] * Found PM-Timer Bug on the chipset. Due to workarounds for a bug,
[ 0.392024] * this clock source is slow. Consider trying other clock sources
[ 0.396024] pci 0000:00:07.3: quirk: region 0f00-0f0f claimed by PIIX4 SMB
[ 0.402229] PCI: Discovered primary peer bus 04 [IRQ]
[ 0.407479] PCI: Discovered primary peer bus 05 [IRQ]
[ 0.412025] PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:07.0
[ 0.416847] PCI: Bridge: 0000:01:00.0
[ 0.420525] IO window: 1000-1fff
[ 0.423924] MEM window: 0xf0000000-0xf00fffff
[ 0.428469] PREFETCH window: 0x0000000040000000-0x00000000400fffff
[ 0.434824] PCI: Bridge: 0000:00:01.0
[ 0.438807] IO window: 1000-1fff
[ 0.442477] MEM window: 0xf0000000-0xf00fffff
[ 0.447007] PREFETCH window: 0x0000000040000000-0x00000000400fffff
[ 0.453362] PCI: Bus 3, cardbus bridge: 0000:00:0f.0
[ 0.458327] IO window: 0x00002800-0x000028ff
[ 0.462773] IO window: 0x00002c00-0x00002cff
[ 0.467218] PREFETCH window: 0x30000000-0x33ffffff
[ 0.472184] MEM window: 0x34000000-0x37ffffff
[ 0.476714] PCI: Bus 7, cardbus bridge: 0000:00:0f.1
[ 0.481677] IO window: 0x00003000-0x000030ff
[ 0.486122] IO window: 0x00003400-0x000034ff
[ 0.490568] PREFETCH window: 0x38000000-0x3bffffff
[ 0.495533] MEM window: 0x3c000000-0x3fffffff
[ 0.500111] PCI: Assigned IRQ 5 for device 0000:00:0f.0
[ 0.505360] PCI: Sharing IRQ 5 with 0000:02:04.0
[ 0.510015] PCI: Assigned IRQ 10 for device 0000:00:0f.1
[ 0.515352] PCI: Sharing IRQ 10 with 0000:02:05.0
[ 0.520134] NET: Registered protocol family 2
[ 0.528029] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.532726] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.539586] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.546724] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.553269] TCP reno registered
[ 0.557586] NET: Registered protocol family 1
[ 0.562324] checking if image is initramfs... it is
[ 2.244702] Freeing initrd memory: 6036k freed
[ 2.250014] platform rtc_cmos: registered platform RTC device (no PNP device found)
[ 2.258449] audit: initializing netlink socket (disabled)
[ 2.263898] type=2000 audit(1698680715.263:1): initialized
[ 2.269702] Total HugeTLB memory allocated, 0
[ 2.274284] VFS: Disk quotas dquot_6.5.1
[ 2.278343] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.285021] msgmni has been set to 1007
[ 2.289568] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 2.296965] io scheduler noop registered
[ 2.300961] io scheduler anticipatory registered
[ 2.305576] io scheduler deadline registered
[ 2.309881] io scheduler cfq registered (default)
[ 2.314605] pci 0000:00:00.0: Limiting direct PCI/PCI transfers
[ 2.321372] isapnp: Scanning for PnP cards...
[ 2.681671] isapnp: No Plug & Play device found
[ 2.692372] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 2.700344] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.706847] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 2.718268] brd: module loaded
[ 2.721739] PNP: No PS/2 controller found. Probing ports directly.
[ 2.983342] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.988464] mice: PS/2 mouse device common for all mice
[ 2.993839] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[ 2.999075] rtc0: alarms up to one day
[ 3.393621] cpuidle: using governor ladder
[ 3.397722] cpuidle: using governor menu
[ 3.401651] No iBFT detected.
[ 3.406056] TCP cubic registered
[ 3.408101] NET: Registered protocol family 17
[ 3.412340] Using IPI No-Shortcut mode
[ 3.416675] registered taskstats version 1
[ 3.421062] rtc_cmos rtc_cmos: hctosys: invalid date/time
[ 3.427272] Freeing unused kernel memory: 244k freed
[ 3.738241] thermal: Unknown symbol acpi_processor_set_thermal_limit
[ 4.644911] Uniform Multi-Platform E-IDE driver
[ 4.649468] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
pnp call arg1=5
[ 4.781506] Linux Tulip driver version 1.1.15-NAPI (Feb 27, 2007)
[ 4.787699] PCI: Assigned IRQ 11 for device 0000:00:0d.0
[ 4.797526] tulip0: EEPROM default media type Autosense.
[ 4.802927] tulip0: Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2) block.
[ 4.810893] tulip0: Index #1 - Media 10baseT-FDX (#4) described by a 21142 Serial PHY (2) block.
[ 4.819761] tulip0: Index #2 - Media 100baseTx (#3) described by a 21143 SYM PHY (4) block.
[ 4.828196] tulip0: Index #3 - Media 100baseTx-FDX (#5) described by a 21143 SYM PHY (4) block.
[ 4.842793] eth0: Digital DS21142/43 Tulip rev 65 at Port 0x2000, 00:a0:8e:36:c2:f0, IRQ 11.
[ 4.853114] PCI: Assigned IRQ 9 for device 0000:00:0e.0
[ 4.857599] PCI: Sharing IRQ 9 with 0000:00:07.2
[ 4.866444] tulip1: EEPROM default media type Autosense.
[ 4.871843] tulip1: Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2) block.
[ 4.878704] tulip1: Index #1 - Media 10baseT-FDX (#4) described by a 21142 Serial PHY (2) block.
[ 4.887572] tulip1: Index #2 - Media 100baseTx (#3) described by a 21143 SYM PHY (4) block.
[ 4.896008] tulip1: Index #3 - Media 100baseTx-FDX (#5) described by a 21143 SYM PHY (4) block.
[ 4.910436] eth1: Digital DS21142/43 Tulip rev 65 at Port 0x2080, 00:a0:8e:36:c2:f1, IRQ 9.
[ 4.920798] PCI: Found IRQ 5 for device 0000:02:04.0
[ 4.925391] PCI: Sharing IRQ 5 with 0000:00:0f.0
[ 4.936137] tulip2: EEPROM default media type Autosense.
[ 4.940145] tulip2: Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2) block.
[ 4.947383] tulip2: Index #1 - Media 10baseT-FDX (#4) described by a 21142 Serial PHY (2) block.
[ 4.956250] tulip2: Index #2 - Media 100baseTx (#3) described by a 21143 SYM PHY (4) block.
[ 4.964687] Clocksource tsc unstable (delta = 68521649 ns)
[ 4.970176] tulip2: Index #3 - Media 100baseTx-FDX (#5) described by a 21143 SYM PHY (4) block.
[ 4.988058] eth2: Digital DS21142/43 Tulip rev 65 at Port 0x1000, 00:a0:8e:36:c2:f2, IRQ 5.
[ 4.996577] PCI: Found IRQ 10 for device 0000:02:05.0
[ 5.001652] PCI: Sharing IRQ 10 with 0000:00:0f.1
[ 5.011885] tulip3: EEPROM default media type Autosense.
[ 5.017284] tulip3: Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2) block.
[ 5.022952] tulip3: Index #1 - Media 10baseT-FDX (#4) described by a 21142 Serial PHY (2) block.
[ 5.026952] tulip3: Index #2 - Media 100baseTx (#3) described by a 21143 SYM PHY (4) block.
[ 5.030952] tulip3: Index #3 - Media 100baseTx-FDX (#5) described by a 21143 SYM PHY (4) block.
[ 5.038953] eth3: Digital DS21142/43 Tulip rev 65 at Port 0x1080, 00:a0:8e:36:c2:f3, IRQ 10.
[ 5.044898] PIIX4: IDE controller (0x8086:0x7111 rev 0x01) at PCI slot 0000:00:07.1
[ 5.050953] PIIX4: not 100% native mode: will probe irqs later
[ 5.054954] ide0: BM-DMA at 0x2400-0x2407
[ 5.058954] ide1: BM-DMA at 0x2408-0x240f
[ 5.070955] usbcore: registered new interface driver usbfs
[ 5.074955] usbcore: registered new interface driver hub
[ 5.078955] usbcore: registered new device driver usb
[ 5.140606] USB Universal Host Controller Interface driver v3.0
[ 5.379205] hda: WDC WD800JB-22JJC0, ATA DISK drive
[ 6.055233] hda: UDMA/33 mode selected
[ 6.627107] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 6.631726] ide1 at 0x170-0x177,0x376 on irq 15
[ 6.636449] uhci_hcd 0000:00:07.2: enabling device (0004 -> 0005)
[ 6.642553] PCI: Found IRQ 9 for device 0000:00:07.2
[ 6.646981] PCI: Sharing IRQ 9 with 0000:00:0e.0
[ 6.650981] uhci_hcd 0000:00:07.2: UHCI Host Controller
[ 6.654981] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
[ 6.658981] uhci_hcd 0000:00:07.2: irq 9, io base 0x00002420
[ 6.662981] usb usb1: configuration #1 chosen from 1 choice
[ 6.666981] hub 1-0:1.0: USB hub found
[ 6.670755] hub 1-0:1.0: 2 ports detected
[ 6.776284] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 6.782981] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.786981] usb usb1: Product: UHCI Host Controller
[ 6.790981] usb usb1: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 6.794981] usb usb1: SerialNumber: 0000:00:07.2
[ 6.847461] SCSI subsystem initialized
[ 6.989535] hda: max request size: 128KiB
[ 7.000936] hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63
[ 7.011153] hda: cache flushes supported
[ 7.015210] hda: hda1 hda2 < hda5 hda6 >
[ 7.421621] PM: Starting manual resume from disk
[ 7.513096] kjournald starting. Commit interval 5 seconds
[ 7.518613] EXT3-fs warning: checktime reached, running e2fsck is recommended
[ 7.522981] EXT3 FS on hda1, internal journal
[ 7.526980] EXT3-fs: recovery complete.
[ 7.530980] EXT3-fs: mounted filesystem with ordered data mode.
[ 128.903956] udevd version 125 started
--
coreboot mailing list: [email protected]
http://www.coreboot.org/mailman/listinfo/coreboot
