Hi, Tom. On 2016/03/10 4:12, Tom Ivar Helbekkmo wrote: > SAITOH Masanobu <[email protected]> writes: > >> You mean your machine works with INTx but it doesn't work on MSI, right? > > That is correct. > >> If so, could you show the full dmesg of the machine? > > Appended below. > >> And, did you test if your machine's problem does occur "without" vlan? > > This is the laptop, which doesn't use vlans. The other machine, the > Poweredge 2650, is my main server, and does all its networking over a > vlan trunk on its wm0 interface. I suspect that its problem is > different, since it works with a -current from October 10th, whereas the > laptop doesn't. > > dmesg output from the laptop after making its wm0 use INTx instead of MSI:
Thank you for your quick reply. I had two ICH9 motherboard but I discarded them because both of them were broken... Now I have no any ICH9 machine. I have some ICH8s and one ICH10. All of them worked, so I had thought that ICH9 worked. I'm sorry that I'm busy because AsiaBSDCon starts today and I'll be absent the next one week from Tokyo. I would be happy if someone(TM) debug and test with variety of ICH9 machines. Regards. > Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, > 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016 > The NetBSD Foundation, Inc. All rights reserved. > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > > NetBSD 7.99.26 (DEJAH) #5: Wed Mar 9 17:36:37 CET 2016 > > [email protected]:/usr/obj/sys/arch/amd64/compile.amd64/DEJAH > total memory = 4083 MB > avail memory = 3945 MB > rnd: seeded with 128 bits > timecounter: Timecounters tick every 10.000 msec > Kernelized RAIDframe activated > timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100 > Dell Inc. Latitude E6400 > mainbus0 (root) > cpu0 at mainbus0 > cpu0: Intel(R) Core(TM)2 Duo CPU T9600 @ 2.80GHz, id 0x1067a > pci0 at mainbus0 bus 0: configuration mode 1 > pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok > pchb0 at pci0 dev 0 function 0: vendor 8086 product 2a40 (rev. 0x07) > agp0 at pchb0: can't find internal VGA config space > ppb0 at pci0 dev 1 function 0: vendor 8086 product 2a41 (rev. 0x07) > ppb0: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x16 > @ 2.5GT/s > pci1 at ppb0 bus 1 > pci1: i/o space, memory space enabled, rd/line, wr/inv ok > vga0 at pci1 dev 0 function 0: vendor 10de product 06eb (rev. 0xa1) > wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation) > wsmux1: connecting to wsdisplay0 > drm at vga0 not configured > wm0 at pci0 dev 25 function 0: 82801I mobile (AMT) LAN Controller (rev. 0x03) > wm0: interrupting at irq 11 > wm0: PCI-Express bus > wm0: 2048 words FLASH > wm0: Ethernet address 00:26:b9:cd:21:c2 > makphy0 at wm0 phy 2: Marvell 88E1149 Gigabit PHY, rev. 1 > makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, > 1000baseT-FDX, auto > uhci0 at pci0 dev 26 function 0: vendor 8086 product 2937 (rev. 0x03) > uhci0: interrupting at irq 10 > usb0 at uhci0: USB revision 1.0 > uhci1 at pci0 dev 26 function 1: vendor 8086 product 2938 (rev. 0x03) > uhci1: interrupting at irq 3 > usb1 at uhci1: USB revision 1.0 > uhci2 at pci0 dev 26 function 2: vendor 8086 product 2939 (rev. 0x03) > uhci2: interrupting at irq 11 > usb2 at uhci2: USB revision 1.0 > ehci0 at pci0 dev 26 function 7: vendor 8086 product 293c (rev. 0x03) > ehci0: interrupting at irq 11 > ehci0: BIOS has given up ownership > ehci0: EHCI version 1.0 > ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 > usb3 at ehci0: USB revision 2.0 > hdaudio0 at pci0 dev 27 function 0: HD Audio Controller > hdaudio0: interrupting at irq 3 > hdafg0 at hdaudio0: vendor 111d product 76b2 > hdafg0: DAC00 2ch: Speaker [Built-In], HP Out [Jack] > hdafg0: DAC01 2ch: Speaker [Jack] > hdafg0: DIG02 2ch: SPDIF Out [Jack] > hdafg0: 2ch/0ch 44100Hz 48000Hz 88200Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3 > audio0 at hdafg0: full duplex, playback, capture, mmap, independent > ppb1 at pci0 dev 28 function 0: vendor 8086 product 2940 (rev. 0x03) > ppb1: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ > 2.5GT/s > pci2 at ppb1 bus 11 > pci2: i/o space, memory space enabled, rd/line, wr/inv ok > ppb2 at pci0 dev 28 function 1: vendor 8086 product 2942 (rev. 0x03) > ppb2: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ > 2.5GT/s > pci3 at ppb2 bus 12 > pci3: i/o space, memory space enabled, rd/line, wr/inv ok > iwn0 at pci3 dev 0 function 0: vendor 8086 product 4235 (rev. 0x00) > iwn0: interrupting at irq 10 > iwn0: MIMO 3T3R, MoW, address 00:21:6a:ba:79:e2 > iwn0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps > iwn0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps > iwn0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps > 36Mbps 48Mbps 54Mbps > ppb3 at pci0 dev 28 function 2: vendor 8086 product 2944 (rev. 0x03) > ppb3: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ > 2.5GT/s > pci4 at ppb3 bus 13 > pci4: i/o space, memory space enabled, rd/line, wr/inv ok > ppb4 at pci0 dev 28 function 3: vendor 8086 product 2946 (rev. 0x03) > ppb4: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ > 2.5GT/s > pci5 at ppb4 bus 14 > pci5: i/o space, memory space enabled, rd/line, wr/inv ok > uhci3 at pci0 dev 29 function 0: vendor 8086 product 2934 (rev. 0x03) > uhci3: interrupting at irq 10 > usb4 at uhci3: USB revision 1.0 > uhci4 at pci0 dev 29 function 1: vendor 8086 product 2935 (rev. 0x03) > uhci4: interrupting at irq 3 > usb5 at uhci4: USB revision 1.0 > uhci5 at pci0 dev 29 function 2: vendor 8086 product 2936 (rev. 0x03) > uhci5: interrupting at irq 11 > usb6 at uhci5: USB revision 1.0 > ehci1 at pci0 dev 29 function 7: vendor 8086 product 293a (rev. 0x03) > ehci1: interrupting at irq 10 > ehci1: BIOS refuses to give up ownership, using force > ehci1: EHCI version 1.0 > ehci1: companion controllers, 2 ports each: uhci3 uhci4 uhci5 > usb7 at ehci1: USB revision 2.0 > ppb5 at pci0 dev 30 function 0: vendor 8086 product 2448 (rev. 0x93) > pci6 at ppb5 bus 3 > pci6: i/o space, memory space enabled > fwohci0 at pci6 dev 1 function 0: vendor 1180 product 0832 (rev. 0x04) > fwohci0: interrupting at irq 10 > fwohci0: OHCI version 1.10 (ROM=0) > fwohci0: No. of Isochronous channels is 4. > fwohci0: EUI64 37:4f:c0:00:34:ae:d8:90 > fwohci0: Phy 1394a available S400, 1 ports. > fwohci0: Link S400, max_rec 2048 bytes. > ieee1394if0 at fwohci0: IEEE1394 bus > fwip0 at ieee1394if0: IP over IEEE1394 > fwohci0: Initiate bus reset > sdhc0 at pci6 dev 1 function 1: vendor 1180 product 0822 (rev. 0x21) > sdhc0: interrupting at irq 11 > sdhc0: SDHC 1.0, rev 4, SDMA, 33000 kHz, HS 3.3V, 512 byte blocks > sdmmc0 at sdhc0 slot 0 > sdhc1 at pci6 dev 1 function 2: vendor 1180 product 0843 (rev. 0x11) > sdhc1: interrupting at irq 11 > sdhc1: SDHC 2.0, rev 4, PIOsdhc1: unknown base clock frequency > sdhc1: couldn't initialize host (0x10) > ichlpcib0 at pci0 dev 31 function 0: vendor 8086 product 2917 (rev. 0x03) > timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000 > ichlpcib0: 24-bit timer > tco0 at ichlpcib0: TCO (watchdog) timer configured. > tco0: Min/Max interval 1/367 seconds > gpio0 at ichlpcib0: 64 pins > ahcisata0 at pci0 dev 31 function 2: vendor 8086 product 282a (rev. 0x03) > ahcisata0: interrupting at irq 10 > ahcisata0: 64-bit DMA > ahcisata0: AHCI revision 1.20, 4 ports, 32 slots, CAP > 0xef22ffe3<SXS,EMS,CCCS,PSC,SSC,PMD,SPM,ISS=0x2=Gen2,SCLO,SAL,SALP,SSS,SSNTF,SNCQ,S64A> > atabus0 at ahcisata0 channel 0 > atabus1 at ahcisata0 channel 1 > atabus2 at ahcisata0 channel 4 > atabus3 at ahcisata0 channel 5 > ichsmb0 at pci0 dev 31 function 3: vendor 8086 product 2930 (rev. 0x03) > ichsmb0: interrupting at irq 10 > iic0 at ichsmb0: I2C bus > isa0 at ichlpcib0 > tpm0 at isa0 iomem 0xfed40000-0xfed44fff irq 7: device 0x200114e4 rev 0x30 > com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo > intr_establish_xname: pic pic0 pin 3: can't share type 3 with 2 > pckbc0 at isa0 port 0x60-0x64 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pms0 at pckbc0 (aux slot) > pckbc0: using irq 12 for aux slot > wsmouse0 at pms0 mux 0 > attimer0 at isa0 port 0x40-0x43 > pcppi0 at isa0 port 0x61 > midi0 at pcppi0: PC speaker > sysbeep0 at pcppi0 > attimer0: attached to pcppi0 > est0 at cpu0: Enhanced SpeedStep > coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=100 > fwohci0: BUS reset > fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode > ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me) > ieee1394if0: bus manager 0 > timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0 > IPsec: Initialized Security Association Processing. > uhub0 at usb0: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > uhub1 at usb1: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 2 ports with 2 removable, self powered > uhub2 at usb2: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub2: 2 ports with 2 removable, self powered > uhub3 at usb3: vendor 8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 > uhub3: 6 ports with 6 removable, self powered > uhub4 at usb4: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub4: 2 ports with 2 removable, self powered > uhub5 at usb5: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub5: 2 ports with 2 removable, self powered > uhub6 at usb6: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub6: 2 ports with 2 removable, self powered > uhub7 at usb7: vendor 8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 > uhub7: 6 ports with 6 removable, self powered > ahcisata0 port 0: device present, speed: 3.0Gb/s > ahcisata0 port 1: device present, speed: 1.5Gb/s > ehci0: handing over full speed device on port 5 to uhci2 > wd0 at atabus0 drive 0 > wd0: <ST9250410ASG> > wd0: drive supports 16-sector PIO transfers, LBA48 addressing > wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors > wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) > wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 > (Ultra/133) (using DMA) > atapibus0 at atabus1: 1 targets > cd0 at atapibus0 drive 0: <PLDS DVD+/-RW DU-8A3S, 911100494545, KD01> cdrom > removable > cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) > cd0(ahcisata0:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 > (Ultra/100) (using DMA) > pad0: outputs: 44100Hz, 16-bit, stereo > audio1 at pad0: half duplex, playback, capture > boot device: wd0 > root on wd0a dumps on wd0b > root file system type: ffs > kern.module.path=/stand/amd64/7.99.26/modules > cd0(ahcisata0:1:0): DEFERRED ERROR, key = 0x2 > ugen0 at uhub2 port 1 > ugen0: Broadcom Corp 5880, rev 1.10/1.01, addr 2 > iwn0: scan request(1) while scanning(0) ignored > wsdisplay0: screen 1 added (80x25, vt100 emulation) > wsdisplay0: screen 2 added (80x25, vt100 emulation) > wsdisplay0: screen 3 added (80x25, vt100 emulation) > wsdisplay0: screen 4 added (80x25, vt100 emulation) > > -tih > -- ----------------------------------------------- SAITOH Masanobu ([email protected] [email protected])
