The TFD 0x2051 corresponds to Media Changed error, with DRDY/ERR status bits. Is it possible this message appears every time you change media in the cd0?
Alternatively, I imagine this could be generated if the drive is setup to hibernate/suspend. Jaromir 2017-11-10 10:49 GMT+01:00 <stefan@hertenberger.bayern>: > Am 2017-11-10 10:22, schrieb Martin Husemann: > >> On Fri, Nov 10, 2017 at 10:11:43AM +0100, stefan@hertenberger.bayern >> wrote: >> >>> Am 2017-11-10 09:57, schrieb Martin Husemann: >>> > Can you show the dmesg part describing your ahcisata devices? >>> >>> ahcisata0 at pci0 dev 31 function 2: vendor 8086 product 1c03 (rev. 0x04) >>> ahcisata0: interrupting at ioapic0 pin 19 >>> ahcisata0: 64-bit DMA >>> ahcisata0: AHCI revision 1.30, 6 ports, 32 slots, CAP >>> 0xef30ff45<EMS,PSC,SSC,PMD,ISS=0x3=Gen3,SCLO,SAL,SALP,SSS, >>> SSNTF,SNCQ,S64A> >>> atabus0 at ahcisata0 channel 0 >>> atabus1 at ahcisata0 channel 1 >>> >> >> And the device at atabus1? >> >> Martin >> > > The complete dmesg out put was attached on the first mail. > > Regards Stefan > > Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, > 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017 > The NetBSD Foundation, Inc. All rights reserved. > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > > NetBSD 8.99.6 (GENERIC) #8: Thu Nov 9 23:16:37 UTC 2017 > root@packard:/usr/build/obj/sys/arch/amd64/compile/GENERIC > total memory = 8043 MB > avail memory = 7788 MB > rnd: seeded with 128 bits > timecounter: Timecounters tick every 10.000 msec > Kernelized RAIDframe activated > running cgd selftest aes-xts-256 aes-xts-512 done > RTC BIOS diagnostic error 0x80<clock_battery> > timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100 > Packard Bell EasyNote TS11HR (V1.20) > mainbus0 (root) > ACPI: RSDP 0x00000000000FE020 000024 (v02 ACRSYS) > ACPI: XSDT 0x0000000096FFE120 00007C (v01 ACRSYS ACRPRDCT 00000001 > 01000013) > ACPI: FACP 0x0000000096FFC000 0000F4 (v04 ACRSYS ACRPRDCT 00000001 1025 > 00040000) > ACPI: DSDT 0x0000000096FF0000 008F53 (v01 ACRSYS ACRPRDCT 00000000 1025 > 00040000) > ACPI: FACS 0x0000000096F6D000 000040 > ACPI: ASF! 0x0000000096FFD000 0000A5 (v32 ACRSYS ACRPRDCT 00000001 1025 > 00040000) > ACPI: HPET 0x0000000096FFB000 000038 (v01 ACRSYS ACRPRDCT 00000001 1025 > 00040000) > ACPI: APIC 0x0000000096FFA000 00008C (v02 ACRSYS ACRPRDCT 00000001 1025 > 00040000) > ACPI: MCFG 0x0000000096FF9000 00003C (v01 ACRSYS ACRPRDCT 00000001 1025 > 00040000) > ACPI: SLIC 0x0000000096FEF000 000176 (v01 ACRSYS ACRPRDCT 00000001 1025 > 00040000) > ACPI: SSDT 0x0000000096FEE000 000BC2 (v01 ACRSYS ACRPRDCT 00001000 1025 > 00040000) > ACPI: BOOT 0x0000000096FEC000 000028 (v01 ACRSYS ACRPRDCT 00000001 1025 > 00040000) > ACPI: ASPT 0x0000000096FE9000 000034 (v07 ACRSYS ACRPRDCT 00000001 1025 > 00040000) > ACPI: SSDT 0x0000000096FE8000 00090C (v01 ACRSYS ACRPRDCT 00003000 1025 > 00040000) > ACPI: SSDT 0x0000000096FE7000 000996 (v01 ACRSYS ACRPRDCT 00003000 1025 > 00040000) > ACPI: Executed 1 blocks of module-level executable AML code > ACPI: 4 ACPI AML tables successfully acquired and loaded > ioapic0 at mainbus0 apid 0: pa 0xfec00000, version 0x20, 24 pins > cpu0 at mainbus0 apid 0 > cpu0: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7 > cpu0: package 0, core 0, smt 0 > cpu1 at mainbus0 apid 1 > cpu1: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7 > cpu1: package 0, core 0, smt 1 > cpu2 at mainbus0 apid 2 > cpu2: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7 > cpu2: package 0, core 1, smt 0 > cpu3 at mainbus0 apid 3 > cpu3: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7 > cpu3: package 0, core 1, smt 1 > cpu4 at mainbus0 apid 4 > cpu4: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7 > cpu4: package 0, core 2, smt 0 > cpu5 at mainbus0 apid 5 > cpu5: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7 > cpu5: package 0, core 2, smt 1 > cpu6 at mainbus0 apid 6 > cpu6: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7 > cpu6: package 0, core 3, smt 0 > cpu7 at mainbus0 apid 7 > cpu7: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7 > cpu7: package 0, core 3, smt 1 > acpi0 at mainbus0: Intel ACPICA 20170831 > acpi0: X/RSDT: OemId <ACRSYS,ACRPRDCT,00000001>, AslId < ,01000013> > acpi0: MCFG: segment 0, bus 0-255, address 0x00000000e0000000 > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFE4010E761810 00067C (v01 PmRef Cpu0Cst 00003001 INTL > 20100121) > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFE4025DC6F410 000303 (v01 PmRef ApIst 00003000 INTL > 20100121) > ACPI: Dynamic OEM Table Load: > ACPI: SSDT 0xFFFFE4010E6915D0 000119 (v01 PmRef ApCst 00003000 INTL > 20100121) > acpi0: SCI interrupting at int 9 > timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900 > hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400) > timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000 > acpiec0 at acpi0 (EC0, PNP0C09): io 0x62,0x66 > FWHD (INT0800) at acpi0 not configured > LDRC (PNP0C02) at acpi0 not configured > attimer1 at acpi0 (TIMR, PNP0100): io 0x40-0x43,0x50-0x53 irq 0 > CWDT (INT3F0D) at acpi0 not configured > pckbc1 at acpi0 (KBC0, PNP0303) (kbd port): io 0x60,0x64 irq 1 > pckbc2 at acpi0 (MSS0, SYN1B16) (aux port): irq 12 > acpiacad0 at acpi0 (ACAD, ACPI0003): ACPI AC Adapter > acpibat0 at acpi0 (BAT0, PNP0C0A-1): ACPI Battery > acpibat0: Simplo Lion rechargeable battery > acpibat0: granularity: low->warn 0.264 Ah, warn->full 3.780 Ah > acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button > acpilid0 at acpi0 (LID0, PNP0C0D): ACPI Lid Switch > acpibut1 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button > acpiwmi0 at acpi0 (WMID, PNP0C14-APGe): ACPI WMI Interface > acpiwmibus at acpiwmi0 not configured > acpiwmi1 at acpi0 (CWMI, PNP0C14-COMP): ACPI WMI Interface > acpiwmibus at acpiwmi1 not configured > PDRC (PNP0C02) at acpi0 not configured > acpivga0 at acpi0 (GFX0): ACPI Display Adapter > acpiout0 at acpivga0 (DD01, 0x0100): ACPI Display Output Device > acpiout1 at acpivga0 (DD02, 0x0240): ACPI Display Output Device > acpiout2 at acpivga0 (DD03, 0x0410): ACPI Display Output Device > acpiout2: brightness levels: [10,20,30,40,50,60,70,80,90,100] > acpiout3 at acpivga0 (DD04, 0x7330): ACPI Display Output Device > acpiout4 at acpivga0 (DD05, 0x0005): ACPI Display Output Device > acpiout5 at acpivga0 (DD06, 0x0006): ACPI Display Output Device > acpiout6 at acpivga0 (DD07, 0x0007): ACPI Display Output Device > acpiout7 at acpivga0 (DD08, 0x0008): ACPI Display Output Device > acpivga0: unknown output device acpiout4 > acpivga0: unknown output device acpiout5 > acpivga0: unknown output device acpiout6 > acpivga0: unknown output device acpiout7 > acpivga0: connected output devices: > acpivga0: 0x0100 (acpiout0): VGA Analog Monitor, index 0, port 0, head 0 > acpivga0: 0x0240 (acpiout1): TV/HDTV Monitor, index 0, port 4, head 0 > acpivga0: 0x0410 (acpiout2): Int. Digital Flat Panel, index 0, port 1, > head 0 > acpivga0: 0x7330 (acpiout3): Ext. Digital Monitor, index 0, port 3, head > 0 > MEM2 (PNP0C01) at acpi0 not configured > PTID (INT340E) at acpi0 not configured > ACPI: Enabled 9 GPEs in block 00 to 3F > pckbd0 at pckbc1 (kbd slot) > pckbc1: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard > pms0 at pckbc1 (aux slot) > pms0: Synaptics touchpad version 7.5 > pms0: Extended W mode, Palm detect, Multi-finger Report, Multi-finger > pckbc1: using irq 12 for aux slot > wsmouse0 at pms0 mux 0 > pci0 at mainbus0 bus 0: configuration mode 1 > pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok > pchb0 at pci0 dev 0 function 0: vendor 8086 product 0104 (rev. 0x09) > i915drmkms0 at pci0 dev 2 function 0: vendor 8086 product 0116 (rev. 0x09) > drm: Memory usable by graphics device = 2048M > drm: Supports vblank timestamp caching Rev 2 (21.10.2013). > drm: Driver supports precise vblank timestamp query. > i915drmkms0: interrupting at ioapic0 pin 16 (i915) > drm: Wrong MCH_SSKPD value: 0x16040307 > drm: This can cause pipe underruns and display issues. > drm: Please upgrade your BIOS to fix this. > intelfb0 at i915drmkms0 > i915drmkms0: info: registered panic notifier > intelfb0: framebuffer at 0xffff80008d70e000, size 1366x768, depth 32, > stride 5504 > wsdisplay0 at intelfb0 kbdmux 1: console (default, vt100 emulation), using > wskbd0 > wsmux1: connecting to wsdisplay0 > vendor 8086 product 1c3a (miscellaneous communications, revision 0x04) at > pci0 dev 22 function 0 not configured > ehci0 at pci0 dev 26 function 0: vendor 8086 product 1c2d (rev. 0x04) > ehci0: interrupting at ioapic0 pin 16 > ehci0: BIOS has given up ownership > ehci0: EHCI version 1.0 > usb0 at ehci0: USB revision 2.0 > hdaudio0 at pci0 dev 27 function 0: HD Audio Controller > hdaudio0: interrupting at msi0 vec 0 > hdafg0 at hdaudio0: vendor 10ec product 0269 > hdafg0: DAC00 2ch: Speaker [Built-In], HP Out [Jack] > hdafg0: ADC01 2ch: Mic In [Built-In] > hdafg0: ADC02 2ch: Mic In [Jack] > hdafg0: 2ch/2ch 44100Hz 48000Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3 > audio0 at hdafg0: full duplex, playback, capture, mmap, independent > hdafg0: Virtual format configured - Format SLINEAR, precision 16, channels > 2, frequency 48000 > hdafg0: Latency: 128 milliseconds > spkr0 at audio0: PC Speaker (synthesized) > wsbell at spkr0 not configured > hdafg1 at hdaudio0: vendor 8086 product 2805 > hdafg1: DP00 8ch: Digital Out [Jack] > hdafg1: 8ch/0ch 48000Hz PCM16* > ppb0 at pci0 dev 28 function 0: vendor 8086 product 1c10 (rev. 0xb4) > ppb0: PCI Express capability version 2 <Root Port of PCI-E Root Complex> > x1 @ 5.0GT/s > ppb0: link is x1 @ 2.5GT/s > pci1 at ppb0 bus 2 > pci1: i/o space, memory space enabled, rd/line, wr/inv ok > bge0 at pci1 dev 0 function 0: Broadcom BCM57785 Gigabit Ethernet > bge0: interrupting at msi1 vec 0 > bge0: HW config 000a0154, 00004004, 00000008, 00000000 00000000 > bge0: ASIC BCM57765 B0 (0x57785100), Ethernet address b8:70:f4:a1:34:91 > bge0: setting short Tx thresholds > brgphy0 at bge0 phy 1: BCM57765 1000BASE-T media interface, rev. 4 > brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, > 1000baseT-FDX, auto > sdhc0 at pci1 dev 0 function 1: vendor 14e4 product 16bc (rev. 0x10) > sdhc0: interrupting at ioapic0 pin 17 > sdhc0: SDHC 2.0, rev 21, SDMA, 50000 kHz, HS 1.8V 3.0V 3.3V, 2048 byte > blocks > sdmmc0 at sdhc0 slot 0 > vendor 14e4 product 16be (miscellaneous system, revision 0x10) at pci1 dev > 0 function 2 not configured > vendor 14e4 product 16bf (miscellaneous system, revision 0x10) at pci1 dev > 0 function 3 not configured > ppb1 at pci0 dev 28 function 1: vendor 8086 product 1c12 (rev. 0xb4) > ppb1: PCI Express capability version 2 <Root Port of PCI-E Root Complex> > x1 @ 5.0GT/s > ppb1: link is x1 @ 2.5GT/s > pci2 at ppb1 bus 3 > pci2: i/o space, memory space enabled, rd/line, wr/inv ok > athn0 at pci2 dev 0 function 0: Atheros AR9287 > athn0: rev 2 (2T2R), ROM rev 4, address 68:a3:c4:d8:95:d8 > athn0: interrupting at ioapic0 pin 17 > athn0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps > athn0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps > 24Mbps 36Mbps 48Mbps 54Mbps > ppb2 at pci0 dev 28 function 3: vendor 8086 product 1c16 (rev. 0xb4) > ppb2: PCI Express capability version 2 <Root Port of PCI-E Root Complex> > x1 @ 5.0GT/s > pci3 at ppb2 bus 5 > pci3: i/o space, memory space enabled, rd/line, wr/inv ok > xhci0 at pci3 dev 0 function 0: vendor 1033 product 0194 (rev. 0x04) > xhci0: interrupting at msi2 vec 0 > xhci0: xHCI version 0.96 > usb1 at xhci0: USB revision 3.0 > usb2 at xhci0: USB revision 2.0 > ehci1 at pci0 dev 29 function 0: vendor 8086 product 1c26 (rev. 0x04) > ehci1: interrupting at ioapic0 pin 23 > ehci1: BIOS has given up ownership > ehci1: EHCI version 1.0 > usb3 at ehci1: USB revision 2.0 > ichlpcib0 at pci0 dev 31 function 0: vendor 8086 product 1c49 (rev. 0x04) > timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000 > ichlpcib0: 24-bit timer > tco0 at ichlpcib0: TCO (watchdog) timer configured. > tco0: Min/Max interval 1/367 seconds > ahcisata0 at pci0 dev 31 function 2: vendor 8086 product 1c03 (rev. 0x04) > ahcisata0: interrupting at ioapic0 pin 19 > ahcisata0: 64-bit DMA > ahcisata0: AHCI revision 1.30, 6 ports, 32 slots, CAP > 0xef30ff45<EMS,PSC,SSC,PMD,ISS=0x3=Gen3,SCLO,SAL,SALP,SSS,SSNTF,SNCQ,S64A> > atabus0 at ahcisata0 channel 0 > atabus1 at ahcisata0 channel 1 > ichsmb0 at pci0 dev 31 function 3: vendor 8086 product 1c22 (rev. 0x04) > ichsmb0: interrupting at ioapic0 pin 19 > iic0 at ichsmb0: I2C bus > isa0 at ichlpcib0 > pcppi0 at isa0 port 0x61 > spkr1 at pcppi0: PC Speaker > wsbell at spkr1 not configured > midi0 at pcppi0: PC speaker > sysbeep0 at pcppi0 > attimer1: attached to pcppi0 > acpicpu0 at cpu0: ACPI CPU > acpicpu0: C1: FFH, lat 1 us, pow 1000 mW > acpicpu0: C3: FFH, lat 104 us, pow 350 mW > acpicpu0: P0: FFH, lat 10 us, pow 45000 mW, 2001 MHz, turbo boost > acpicpu0: P1: FFH, lat 10 us, pow 45000 mW, 2000 MHz > acpicpu0: P2: FFH, lat 10 us, pow 42264 mW, 1900 MHz > acpicpu0: P3: FFH, lat 10 us, pow 39581 mW, 1800 MHz > acpicpu0: P4: FFH, lat 10 us, pow 36953 mW, 1700 MHz > acpicpu0: P5: FFH, lat 10 us, pow 34377 mW, 1600 MHz > acpicpu0: P6: FFH, lat 10 us, pow 31853 mW, 1500 MHz > acpicpu0: P7: FFH, lat 10 us, pow 29388 mW, 1400 MHz > acpicpu0: P8: FFH, lat 10 us, pow 26968 mW, 1300 MHz > acpicpu0: P9: FFH, lat 10 us, pow 24598 mW, 1200 MHz > acpicpu0: P10: FFH, lat 10 us, pow 22280 mW, 1100 MHz > acpicpu0: P11: FFH, lat 10 us, pow 20012 mW, 1000 MHz > acpicpu0: P12: FFH, lat 10 us, pow 17797 mW, 900 MHz > acpicpu0: P13: FFH, lat 10 us, pow 15628 mW, 800 MHz > acpicpu0: T0: I/O, lat 1 us, pow 0 mW, 100 % > acpicpu0: T1: I/O, lat 1 us, pow 0 mW, 88 % > acpicpu0: T2: I/O, lat 1 us, pow 0 mW, 76 % > acpicpu0: T3: I/O, lat 1 us, pow 0 mW, 64 % > acpicpu0: T4: I/O, lat 1 us, pow 0 mW, 52 % > acpicpu0: T5: I/O, lat 1 us, pow 0 mW, 40 % > acpicpu0: T6: I/O, lat 1 us, pow 0 mW, 28 % > acpicpu0: T7: I/O, lat 1 us, pow 0 mW, 16 % > coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=100 > acpicpu1 at cpu1: ACPI CPU > acpicpu2 at cpu2: ACPI CPU > coretemp1 at cpu2: thermal sensor, 1 C resolution, Tjmax=100 > acpicpu3 at cpu3: ACPI CPU > acpicpu4 at cpu4: ACPI CPU > coretemp2 at cpu4: thermal sensor, 1 C resolution, Tjmax=100 > acpicpu5 at cpu5: ACPI CPU > acpicpu6 at cpu6: ACPI CPU > coretemp3 at cpu6: thermal sensor, 1 C resolution, Tjmax=100 > acpicpu7 at cpu7: ACPI CPU > timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0 > timecounter: Timecounter "TSC" frequency 1995574920 Hz quality 3000 > uhub0 at usb1: vendor 1033 (0x1033) xHCI Root Hub (0000), class 9/0, rev > 1.00/1.00, addr 0 > uhub0: 2 ports with 2 removable, self powered > uhub1 at usb2: vendor 1033 (0x1033) xHCI Root Hub (0000), class 9/0, rev > 2.00/1.00, addr 0 > uhub1: 2 ports with 2 removable, self powered > IPsec: Initialized Security Association Processing. > uhub2 at usb0: vendor 8086 (0x8086) EHCI root hub (0000), class 9/0, rev > 2.00/1.00, addr 1 > uhub2: 2 ports with 2 removable, self powered > uhub3 at usb3: vendor 8086 (0x8086) EHCI root hub (0000), class 9/0, rev > 2.00/1.00, addr 1 > uhub3: 2 ports with 2 removable, self powered > ahcisata0 port 0: device present, speed: 3.0Gb/s > ahcisata0 port 1: device present, speed: 1.5Gb/s > acpiacad0: AC adapter online. > drm: Enabling RC6 states: RC6 on, RC6p off, RC6pp off > wd0 at atabus0 drive 0 > wd0: <WDC WD3200BEKT-00F3T0> > wd0: drive supports 16-sector PIO transfers, LBA48 addressing > wd0: 298 GB, 620181 cyl, 16 head, 63 sec, 512 bytes/sect x 625142448 > sectors > wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), > WRITE DMA FUA, NCQ (32 tags) > wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 > (Ultra/133) (using DMA), NCQ (31 tags) > atapibus0 at atabus1: 1 targets > cd0 at atapibus0 drive 0: <PIONEER DVD-RW DVRTD10RS, SCB1403891, 1.00> > cdrom removable > cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) > cd0(ahcisata0:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 > (Ultra/100) (using DMA) > uhub4 at uhub3 port 1: vendor 8087 (0x8087) product 0024 (0x24), class > 9/0, rev 2.00/0.00, addr 2 > uhub4: single transaction translator > uhub4: 6 ports with 6 removable, self powered > uhub5 at uhub2 port 1: vendor 8087 (0x8087) product 0024 (0x24), class > 9/0, rev 2.00/0.00, addr 2 > uhub5: single transaction translator > uhub5: 6 ports with 6 removable, self powered > uhidev0 at uhub4 port 2 configuration 1 interface 0 > uhidev0: Logitech (0x46d) USB Receiver (0xc52f), rev 2.00/30.00, addr 3, > iclass 3/1 > ums0 at uhidev0: 16 buttons, W and Z dirs > wsmouse1 at ums0 mux 0 > uhidev1 at uhub4 port 2 configuration 1 interface 1 > uhidev1: Logitech (0x46d) USB Receiver (0xc52f), rev 2.00/30.00, addr 3, > iclass 3/0 > uhidev1: 17 report ids > uhid0 at uhidev1 reportid 3: input=4, output=0, feature=0 > uhid1 at uhidev1 reportid 16: input=6, output=6, feature=0 > uhid2 at uhidev1 reportid 17: input=19, output=19, feature=0 > uvideo0 at uhub5 port 3 configuration 1 interface 0: AAB5R0114 (0x58f) > 1.3M HD WebCam (0xb002), rev 2.00/0.02, addr 3 > video0 at uvideo0: AAB5R0114 (0x58f) 1.3M HD WebCam (0xb002), rev > 2.00/0.02, addr 3 > urtwn0 at uhub4 port 4 > urtwn0: Realtek (0x7392) 802.11n WLAN Adapter (0x7811), rev 2.00/2.00, > addr 4 > urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R, address 74:da:38:88:7c:ad > urtwn0: 1 rx pipe, 2 tx pipes > urtwn0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps > urtwn0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps > 24Mbps 36Mbps 48Mbps 54Mbps > WARNING: 4 errors while detecting hardware; check system log. > boot device: wd0 > root on wd0a dumps on wd0b > root file system type: ffs > kern.module.path=/stand/amd64/8.99.6/modules > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > acpibat0: normal capacity on 'charge state' > wsdisplay0: screen 1 added (default, vt100 emulation) > wsdisplay0: screen 2 added (default, vt100 emulation) > wsdisplay0: screen 3 added (default, vt100 emulation) > wsdisplay0: screen 4 added (default, vt100 emulation) > > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 > ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051 >