On Tue, 3 Oct 2017 18:50:16 +0200, Franjo wrote: > I've done it, but it doesnt work. > > No I've cropmarks in the preview and the print is also with > border. In the preference I didn't find the option borderless.
I see; the print module doesn't give you access to the full set of printer features. What you're going to have to do is configure the printer queue to be borderless. To do that (for the Gutenprint driver): * Browse http://localhost:631/printers. * Select the printer you want to configure. * Select Administration->Set Default Options from the Administration button under the printer name -- NOT the Administration tab at the top of the page. * In the General options, you'll see an option Shrink Page If Necessary to Fit Borders. Select Expand, and click Set Default Options. You will probably need to enter root and the root password into an authentication dialog. * In the Printer Feature Common options, you'll see a Borderless option. Select Yes, and click Set Default Options again. You may need to enter your credentials again. This will modify the queue so your prints will be borderless and full bleed. > Am 03.10.2017 um 17:49 schrieb Robert Krawitz: >> (Again, please reply-all rather than reply) >> >> On Tue, 3 Oct 2017 17:35:08 +0200, Franjo wrote: >>> Now, I've installed the printer-driver-gutenprint 5.2.11-1 >>> >>> The same problem before. Where I see which driver is in use ?? Is it >>> possible there is an other driver in use? >> You need to create a new printer queue using the Gutenprint driver. >> The driver will be named "Epson Stylus Photo R3000 - CUPS+Gutenprint v5.2.11" >> >>> Borderless print is active >>> >>> >>> Am 03.10.2017 um 16:40 schrieb Robert Krawitz: >>>> (Please use reply-all rather than just reply; other people may be >>>> interested) >>>> >>>> On Tue, 3 Oct 2017 16:32:52 +0200, Franjo wrote: >>>>> Am 03.10.2017 um 16:10 schrieb Robert Krawitz: >>>>>> On Tue, 3 Oct 2017 15:55:03 +0200, Franjo wrote: >>>>>>> Hi @all, >>>>>>> >>>>>>> I'm using LinuxMint 18 and Dt 2.2.5 >>>>>>> >>>>>>> today I wanted to print with Darktable for the first time. But I can >>>>>>> not print without borders. In the printer driver I have set >>>>>>> borderless. Where is the mistake? >>>>>> Which driver are you using? >>>>>> >>>>>> Are you getting borderless on either the long or the short edge but >>>>>> not the other? If so, you should crop the image to the exact form >>>>>> factor of the paper you're trying to print to. For example, if you're >>>>>> trying to print to 6x8" paper, crop your image to an exact (or as >>>>>> close as possible) 4:3 form factor prior to printing. >>>>> where I see which driver I use ?? >>>>> I downloaded the following Epson driver from their Homepage and >>>>> installed it. >>>>> I'm using Epson Stylus Photo R3000 >>>>> >>>>> epson-inkjet-printer-escpr_1.6.16-1lsb3.2_amd64.deb >>>>> >>>>> I have crop the image until I have seen no white borders. >>>>> The output on 5x7 (13x18cm) has exactly 3mm borders on all sides >>>> Can you try the Gutenprint driver, which should be available on your >>>> system? The R3000 is fully supported, and this printer does support >>>> borderless printing. >>>> >>>> Make sure to set "Shrink Page If Necessary to Fit Borders" (in the >>>> advanced options) to "Expand (use maximum page area)". -- Robert Krawitz <[email protected]> *** MIT Engineers A Proud Tradition http://mitathletics.com *** Member of the League for Programming Freedom -- http://ProgFree.org Project lead for Gutenprint -- http://gimp-print.sourceforge.net "Linux doesn't dictate how I work, I dictate how Linux works." --Eric Crampton ____________________________________________________________________________ darktable user mailing list to unsubscribe send a mail to [email protected]
