hello, everyone
i follow the steps as:
$ make mrproper
$ make davinci_evm_dm644x_defconfig
$ make uImage
$ make modules
$ make modules_install
but the new uImage from the latest git sources
cann't start with u-boot-594-nand.bin,it shows as:
Uncompressing
Linux.........................................................................................
done, booting the kernel.
Linux version 2.6.18-omap1-g82f5d268-dirty
([EMAIL PROTECTED]) (gcc version 3.4.3
(MontaVista 3.4.3-25.0.30.0501131 2005-07-23)) #2
F6CPU: ARM926EJ-S [41069265] revision 5
(ARMv5TEJ), cr=00053177
Machine: DaVinci EVM
Memory policy: ECC disabled, Data cache writeback
DM6443
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32
byte lines, 128 sets
CPU0: D cache: 8192 bytes, associativity 4, 32
byte lines, 64 sets
Built 1 zonelists. Total pages: 30720
Kernel command line: console=ttyS0,115200n8
noinitrd rw ip=dhcp root=/dev/nfs
nfsroot=192.168.0.137:/opt/mv_pro_4.0/montavista/pro/devkit/arm/MPID
hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4,
65536 bytes)
Inode-cache hash table entries: 8192 (order: 3,
32768 bytes)
Memory: 120MB = 120MB total
Memory: 118784KB available (2260K code, 525K data,
112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
WARNING: both IDE and NOR flash are enabled, but
are pin-muxed.
Disable IDE for NOR support.
DaVinci: 71 gpio irqs
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0,
4096 bytes)
TCP established hash table entries: 4096 (order:
2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192
bytes)
TCP: Hash tables configured (established 4096 bind
2048)
TCP reno registered
Initializing DaVinci McBSP system
Installing knfsd (copyright (C) 1996
[EMAIL PROTECTED]).
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
Setting Up Clocks for DM420 OSD
Console: switching to colour frame buffer device 90x30
fb0: dm_osd0_fb frame buffer device
fb1: dm_vid0_fb frame buffer device
fb2: dm_osd1_fb frame buffer device
fb3: dm_vid1_fb frame buffer device
Serial: 8250/16550 driver $Revision: 1.90 $ 2
ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40)
is a 16550A
RAMDISK driver initialized: 1 RAM disks of 32768K
size 1024 blocksize
TI DaVinci EMAC: MAC address is 00:0e:99:02:52:42
TI DaVinci EMAC Linux version updated 4.0
TI DaVinci EMAC: Installed 1 instances.
netconsole: not configured, aborting
Linux video capture interface: v2.00
i2c /dev entries driver
TLV320AIC23 I2C version 1.8 (10-Feb-2006)
Uniform Multi-Platform E-IDE driver Revision:
7.00alpha2
ide: Assuming 50MHz system bus speed for PIO
modes; override with idebus=xx
hda: TOSHIBA MK4032GAX, ATA DISK drive
ide0 at 0xe10661f0-0xe10661f7,0xe10663f6 on irq 22
hda: max request size: 512KiB
hda: 78140160 sectors (40007 MB), CHS=16383/255/63
hda: cache flushes supported
hda: hda1 hda2
ide0: BM-DMA at 0xe1066000-0xe1066007, BIOS
settings: hda:pio, hdb:pio
physmap platform flash device: 01000000 at 02000000
physmap-flash physmap-flash.0: map_probe failed
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Sending DHCP requests .., OK
IP-Config: Got DHCP answer from 192.168.0.137, my
address is 192.168.0.4
IP-Config: Complete:
device=eth0, addr=192.168.0.4,
mask=255.255.255.0, gw=192.168.0.137,
host=192.168.0.4, domain=, nis-domain=(none),
bootserver=192.168.0.137,
rootserver=192.168.0.137, rootpath=
Looking up port of RPC 100003/2 on 192.168.0.137
Looking up port of RPC 100005/1 on 192.168.0.137
VFS: Mounted root (nfs filesystem).
Freeing init memory: 112K
Starting system log daemon: .
//then stop
------------------
after i upload the new
modules(2.6.18-omap1-g02c19243-dirty) in the
target board in /lib/modules and delete the 2.6.10
modules,then restart the uImage, it shows as:
.....................................
physmap platform flash device: 01000000 at 02000000
physmap-flash physmap-flash.0: map_probe failed
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Sending DHCP requests .., OK
IP-Config: Got DHCP answer from 192.168.0.137, my
address is 192.168.0.4
IP-Config: Complete:
device=eth0, addr=192.168.0.4,
mask=255.255.255.0, gw=192.168.0.137,
host=192.168.0.4, domain=, nis-domain=(none),
bootserver=192.168.0.137,
rootserver=192.168.0.137, rootpath=
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached,
running e2fsck is recommended
EXT3 FS on hda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Freeing init memory: 112K
Starting system log daemon: cmemk: disagrees about
version of symbol struct_module
syslogd klogd.
Starting NFS common utilities: statd lockd.
Starting internet superserver: inetd.
insmod: error inserting 'cmemk.ko': -1 Invalid
module format
dsplinkk: no version for "struct_module" found:
kernel tainted.
dsplinkk: version magic '2.6.10_mvl401 preempt
ARMv5 gcc-3.4' should be
'2.6.18-omap1-g82f5d268-dirty mod_unload ARMv5
gcc-3.4'
//then stop
anyone can help me? thanks
--
USTC Alumni Email System
_______________________________________________
Davinci-linux-open-source mailing list
[email protected]
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
