This patch fixes Nand largepage support for Davinci
Changes the ecc values stored in the spare bytes so that
an erased block does not contain ecc errors.
The ecc correction function is much easier to read.
Chip select other than CS2 should also work now but not tested.
The bus width now comes from the EM_WIDTH pin.

Linux must be modified to match the ecc if it will
read blocks that u-boot writes

Signed-off-by: Troy Kisky <[EMAIL PROTECTED]>

diff --git a/cpu/arm926ejs/davinci/nand.c b/cpu/arm926ejs/davinci/nand.c
index 127be9f..f5c3135 100644
--- a/cpu/arm926ejs/davinci/nand.c
+++ b/cpu/arm926ejs/davinci/nand.c
@@ -52,32 +52,36 @@

 extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];

-static void nand_davinci_hwcontrol(struct mtd_info *mtd, int cmd)
-{
-    struct        nand_chip *this = mtd->priv;
-    u_int32_t    IO_ADDR_W = (u_int32_t)this->IO_ADDR_W;

-    IO_ADDR_W &= ~(MASK_ALE|MASK_CLE);
+unsigned char nandCtlSetClr[] = {
+    0x00,        //1 - NAND_CTL_SETNCE, 2 - NAND_CTL_CLRNCE, Select/Deselect 
Chip Select (nCE)
+    MASK_CLE,    //3 - NAND_CTL_SETCLE, 4 - NAND_CTL_CLRCLE, Select/Deselect 
the command latch (CLE)
+    MASK_ALE,    //5 - NAND_CTL_SETALE, 6 - NAND_CTL_CLRALE, Select/Deselect 
the address latch (ALE)
+    0x00,        //7 - NAND_CTL_SETWP,  8 - NAND_CTL_CLRWP,  Set/Clear write 
protection (WP) Not used!
+};

-    switch (cmd) {
-        case NAND_CTL_SETCLE:
-            IO_ADDR_W |= MASK_CLE;
-            break;
-        case NAND_CTL_SETALE:
-            IO_ADDR_W |= MASK_ALE;
-            break;
+static void nand_davinci_hwcontrol(struct mtd_info *mtd, int cmd)
+{
+    cmd--;
+    if ((cmd>=0)&&(cmd<8)) {
+        struct        nand_chip *nand = mtd->priv;
+        u_int32_t    addr = (u_int32_t)nand->IO_ADDR_W;
+        if (cmd&1) addr &= ~nandCtlSetClr[cmd>>1];
+        else addr |= nandCtlSetClr[cmd>>1];
+        nand->IO_ADDR_W = (void *)addr;
+//        DEBUG (MTD_DEBUG_LEVEL3, "cmd:0x%x newAddress: 0x%x\n",cmd+1,addr);
+    } else {
+        DEBUG (MTD_DEBUG_LEVEL0, "Invalid command 0x%x\n",cmd+1);
     }
-
-    this->IO_ADDR_W = (void *)IO_ADDR_W;
 }

 /* Set WP on deselect, write enable on select */
 static void nand_davinci_select_chip(struct mtd_info *mtd, int chip)
 {
+#ifdef SONATA_BOARD_GPIOWP
 #define GPIO_SET_DATA01    0x01c67018
 #define GPIO_CLR_DATA01    0x01c6701c
 #define GPIO_NAND_WP    (1 << 4)
-#ifdef SONATA_BOARD_GPIOWP
     if (chip < 0) {
         REG(GPIO_CLR_DATA01) |= GPIO_NAND_WP;
     } else {
@@ -105,226 +109,176 @@ static struct nand_oobinfo davinci_nand_oobinfo = {
 #error "Either CFG_NAND_LARGEPAGE or CFG_NAND_SMALLPAGE must be defined!"
 #endif

-static void nand_davinci_enable_hwecc(struct mtd_info *mtd, int mode)
-{
-    emifregs    emif_addr;
-    int        dummy;
-
-    emif_addr = (emifregs)DAVINCI_ASYNC_EMIF_CNTRL_BASE;
-
-    dummy = emif_addr->NANDF1ECC;
-    dummy = emif_addr->NANDF2ECC;
-    dummy = emif_addr->NANDF3ECC;
-    dummy = emif_addr->NANDF4ECC;
-
-    emif_addr->NANDFCR |= (1 << 8);
-}

-static u_int32_t nand_davinci_readecc(struct mtd_info *mtd, u_int32_t region)
+static u_int32_t nand_davinci_readecc(struct mtd_info *mtd, u_int32_t chipNum)
 {
     u_int32_t    ecc = 0;
     emifregs    emif_base_addr;

     emif_base_addr = (emifregs)DAVINCI_ASYNC_EMIF_CNTRL_BASE;
-
-    if (region == 1)
-        ecc = emif_base_addr->NANDF1ECC;
-    else if (region == 2)
-        ecc = emif_base_addr->NANDF2ECC;
-    else if (region == 3)
-        ecc = emif_base_addr->NANDF3ECC;
-    else if (region == 4)
-        ecc = emif_base_addr->NANDF4ECC;
-
+    ecc = emif_base_addr->NANDF_ECC[chipNum];
     return(ecc);
 }
-
-static int nand_davinci_calculate_ecc(struct mtd_info *mtd, const u_char *dat, 
u_char *ecc_code)
-{
-    u_int32_t        tmp;
-    int            region, n;
-    struct nand_chip    *this = mtd->priv;
-
-    n = (this->eccmode == NAND_ECC_HW12_2048) ? 4 : 1;
-
-    region = 1;
-    while (n--) {
-        tmp = nand_davinci_readecc(mtd, region);
-        *ecc_code++ = tmp;
-        *ecc_code++ = tmp >> 16;
-        *ecc_code++ = ((tmp >> 8) & 0x0f) | ((tmp >> 20) & 0xf0);
-        region++;
-    }
-    return(0);
-}
-
-static void nand_davinci_gen_true_ecc(u_int8_t *ecc_buf)
+static void nand_davinci_enable_hwecc(struct mtd_info *mtd, int mode)
 {
-    u_int32_t    tmp = ecc_buf[0] | (ecc_buf[1] << 16) | ((ecc_buf[2] & 0xf0) << 20) | 
((ecc_buf[2] & 0x0f) << 8);
+    struct        nand_chip *nand = mtd->priv;
+    u_int32_t    addr = (u_int32_t)nand->IO_ADDR_R;
+    u_int32_t   chipNum=(addr-CFG_NAND_BASE)>>25;        //0 - cs2, 1 - cs3, 2 
- cs4, 3 - cs5
+    emifregs    emif_addr;
+    int        dummy;
+    if (chipNum>=4) return;

-    ecc_buf[0] = ~(P64o(tmp) | P64e(tmp) | P32o(tmp) | P32e(tmp) | P16o(tmp) | 
P16e(tmp) | P8o(tmp) | P8e(tmp));
-    ecc_buf[1] = ~(P1024o(tmp) | P1024e(tmp) | P512o(tmp) | P512e(tmp) | 
P256o(tmp) | P256e(tmp) | P128o(tmp) | P128e(tmp));
-    ecc_buf[2] = ~( P4o(tmp) | P4e(tmp) | P2o(tmp) | P2e(tmp) | P1o(tmp) | 
P1e(tmp) | P2048o(tmp) | P2048e(tmp));
+//    DEBUG (MTD_DEBUG_LEVEL3, "enable_hwecc\n");
+    emif_addr = (emifregs)DAVINCI_ASYNC_EMIF_CNTRL_BASE;
+    dummy = nand_davinci_readecc(mtd, chipNum);    //reset ecc to 0
+    emif_addr->NANDFCR |= (1 << (8+chipNum));    //start ECC on chip select 
region+2
 }

-static int nand_davinci_compare_ecc(u_int8_t *ecc_nand, u_int8_t *ecc_calc, 
u_int8_t *page_data)
+static int nand_davinci_calculate_ecc(struct mtd_info *mtd, const u_char *dat, 
u_char *ecc_code)
 {
-    u_int32_t    i;
-    u_int8_t    tmp0_bit[8], tmp1_bit[8], tmp2_bit[8];
-    u_int8_t    comp0_bit[8], comp1_bit[8], comp2_bit[8];
-    u_int8_t    ecc_bit[24];
-    u_int8_t    ecc_sum = 0;
-    u_int8_t    find_bit = 0;
-    u_int32_t    find_byte = 0;
-    int        is_ecc_ff;
-
-    is_ecc_ff = ((*ecc_nand == 0xff) && (*(ecc_nand + 1) == 0xff) && 
(*(ecc_nand + 2) == 0xff));
-
-    nand_davinci_gen_true_ecc(ecc_nand);
-    nand_davinci_gen_true_ecc(ecc_calc);
-
-    for (i = 0; i <= 2; i++) {
-        *(ecc_nand + i) = ~(*(ecc_nand + i));
-        *(ecc_calc + i) = ~(*(ecc_calc + i));
-    }
-
-    for (i = 0; i < 8; i++) {
-        tmp0_bit[i] = *ecc_nand % 2;
-        *ecc_nand = *ecc_nand / 2;
-    }
-
-    for (i = 0; i < 8; i++) {
-        tmp1_bit[i] = *(ecc_nand + 1) % 2;
-        *(ecc_nand + 1) = *(ecc_nand + 1) / 2;
-    }
-
-    for (i = 0; i < 8; i++) {
-        tmp2_bit[i] = *(ecc_nand + 2) % 2;
-        *(ecc_nand + 2) = *(ecc_nand + 2) / 2;
-    }
-
-    for (i = 0; i < 8; i++) {
-        comp0_bit[i] = *ecc_calc % 2;
-        *ecc_calc = *ecc_calc / 2;
+    struct        nand_chip *nand = mtd->priv;
+    u_int32_t    addr = (u_int32_t)nand->IO_ADDR_R;
+    u_int32_t   chipNum=(addr-CFG_NAND_BASE)>>25;        //0 - cs2, 1 - cs3, 2 
- cs4, 3 - cs5
+    if (chipNum>=4) return -1;
+    u_int32_t    tmp = nand_davinci_readecc(mtd, chipNum);
+#ifdef CONFIG_MTD_DEBUG
+    //calculate it ourself and compare
+//#define FORCE_ECC_ERROR        //this is commented out for normal operation
+#ifdef FORCE_ECC_ERROR
+    {
+        //force single bit ecc error to test ecc correction code
+        u_char* p = (u_char*)dat;
+        unsigned int i = p[0] | (p[1]<<8);    //1st word of block determines 
which bit is made in error
+        i &= 0xfff;
+        p[i>>3] ^= 1<<(i&7);
+        printf("Forcing ecc error, byte:%d, bit:%d\n",i>>3,i&7);
     }
-
-    for (i = 0; i < 8; i++) {
-        comp1_bit[i] = *(ecc_calc + 1) % 2;
-        *(ecc_calc + 1) = *(ecc_calc + 1) / 2;
-    }
-
-    for (i = 0; i < 8; i++) {
-        comp2_bit[i] = *(ecc_calc + 2) % 2;
-        *(ecc_calc + 2) = *(ecc_calc + 2) / 2;
-    }
-
-    for (i = 0; i< 6; i++)
-        ecc_bit[i] = tmp2_bit[i + 2] ^ comp2_bit[i + 2];
-
-    for (i = 0; i < 8; i++)
-        ecc_bit[i + 6] = tmp0_bit[i] ^ comp0_bit[i];
-
-    for (i = 0; i < 8; i++)
-        ecc_bit[i + 14] = tmp1_bit[i] ^ comp1_bit[i];
-
-    ecc_bit[22] = tmp2_bit[0] ^ comp2_bit[0];
-    ecc_bit[23] = tmp2_bit[1] ^ comp2_bit[1];
-
-    for (i = 0; i < 24; i++)
-        ecc_sum += ecc_bit[i];
-
-    switch (ecc_sum) {
-        case 0:
-            /* Not reached because this function is not called if
-               ECC values are equal */
-            return 0;
-        case 1:
-            /* Uncorrectable error */
-            DEBUG (MTD_DEBUG_LEVEL0, "ECC UNCORRECTED_ERROR 1\n");
-            return(-1);
-        case 12:
-            /* Correctable error */
-            find_byte = (ecc_bit[23] << 8) +
-                (ecc_bit[21] << 7) +
-                (ecc_bit[19] << 6) +
-                (ecc_bit[17] << 5) +
-                (ecc_bit[15] << 4) +
-                (ecc_bit[13] << 3) +
-                (ecc_bit[11] << 2) +
-                (ecc_bit[9]  << 1) +
-                ecc_bit[7];
-
-            find_bit = (ecc_bit[5] << 2) + (ecc_bit[3] << 1) + ecc_bit[1];
-
-            DEBUG (MTD_DEBUG_LEVEL0, "Correcting single bit ECC error at offset: 
%d, bit: %d\n", find_byte, find_bit);
-
-            page_data[find_byte] ^= (1 << find_bit);
-
-            return(0);
-        default:
-            if (is_ecc_ff) {
-                if (ecc_calc[0] == 0 && ecc_calc[1] == 0 && ecc_calc[2] == 0)
-                    return(0);
-            }
-            DEBUG (MTD_DEBUG_LEVEL0, "UNCORRECTED_ERROR default\n");
-            return(-1);
+#endif
+    {
+        unsigned int i = 0x00000fff;    //2**12 bits/ecc
+        unsigned int j = 512;            //512 bytes/ecc
+        unsigned int ecc = 0;
+        do {
+            unsigned int k=i;
+            unsigned int v = *dat++;
+            do {
+                if (v&1) ecc ^= k;
+                k += (1<<16);
+                k--;
+                v >>= 1;
+            } while (v);
+            i += 8<<16;
+            i -= 8;
+            j--;
+        } while (j);
+        if (tmp!=ecc) {
+#ifndef FORCE_ECC_ERROR
+            printf("Hardware Ecc: %x, Calculated: %x\n",tmp,ecc);
+#endif
+            tmp=ecc;
+        }
     }
+#endif
+    tmp = (tmp&0x0fff)|((tmp&0x0fff0000)>>4);        //squeeze 0 middle bits 
out so that it fits in 3 bytes
+    tmp = ~tmp;                                    //invert so that erased 
block ecc is correct
+    *ecc_code++ = (u_char)(tmp);
+    *ecc_code++ = (u_char)(tmp >> 8);
+    *ecc_code++ = (u_char)(tmp >> 16);
+    return(0);
 }

+
 static int nand_davinci_correct_data(struct mtd_info *mtd, u_char *dat, u_char 
*read_ecc, u_char *calc_ecc)
 {
-    struct nand_chip    *this;
-    int            block_count = 0, i, rc;
-
-    this = mtd->priv;
-    block_count = (this->eccmode == NAND_ECC_HW12_2048) ? 4 : 1;
-    for (i = 0; i < block_count; i++) {
-        if (memcmp(read_ecc, calc_ecc, 3) != 0) {
-            rc = nand_davinci_compare_ecc(read_ecc, calc_ecc, dat);
-            if (rc < 0) {
-                return(rc);
-            }
+    u_int32_t    eccNand = read_ecc[0] | (read_ecc[1]<<8) | (read_ecc[2]<< 16);
+    u_int32_t    eccCalc = calc_ecc[0] | (calc_ecc[1]<<8) | (calc_ecc[2]<< 16);
+    u_int32_t    diff = eccCalc ^ eccNand;
+    if (diff) {
+        if ((((diff>>12)^diff)&0xfff)!=0xfff) {
+            u_int32_t hwCalc = (~eccCalc)&0xffffff;
+            hwCalc = (hwCalc&0xfff)|((hwCalc&0xfff000)<<4);
+            /* Uncorrectable error */
+            DEBUG (MTD_DEBUG_LEVEL0, "ECC UNCORRECTED_ERROR diff:%x nandBlock:%x 
calc:%x hwCalc:%08x\n",diff,eccNand,eccCalc,hwCalc);
+            return(-1);
         }
-        read_ecc += 3;
-        calc_ecc += 3;
-        dat += 512;
+        /* Correctable error */
+        DEBUG (MTD_DEBUG_LEVEL0, "Correcting single bit ECC error at offset: %d, bit: %d\n", 
diff>>(12+3), ((diff>>12)&7));
+        dat[diff>>(12+3)] ^= (1 << ((diff>>12)&7));
     }
     return(0);
 }
 #endif

+#ifdef NAND_GPIO_READY_LIST
+static unsigned char nandGpioReadyList[] = {NAND_GPIO_READY_LIST};
+#endif
+
 static int nand_davinci_dev_ready(struct mtd_info *mtd)
 {
-    emifregs    emif_addr;
-
-    emif_addr = (emifregs)DAVINCI_ASYNC_EMIF_CNTRL_BASE;
-
-    return(emif_addr->NANDFSR & 0x1);
+#ifdef NAND_GPIO_READY_LIST
+#define GP_BANK0_OFFSET    0x10
+#define GP_BANK_LENGTH    0x28
+#define GP_DIR 0x00
+#define GP_OUT 0x04
+#define GP_SET 0x08
+#define GP_CLR 0x0C
+#define GP_IN  0x10
+
+    struct        nand_chip *nand = mtd->priv;
+    u_int32_t    addr = (u_int32_t)nand->IO_ADDR_R;
+    u_int32_t   chipNum=(addr-CFG_NAND_BASE)>>25;        //0 - cs2, 1 - cs3, 2 
- cs4, 3 - cs5
+    if (chipNum<4) {
+        unsigned int gp = nandGpioReadyList[chipNum];
+        if (gp) {
+            unsigned int bank = (gp>>5);
+            volatile unsigned int* p = (unsigned 
int*)(DAVINCI_GPIO_BASE+GP_BANK0_OFFSET+(bank*GP_BANK_LENGTH));
+            int ret = (p[GP_IN>>2] >> (gp&0x1f))&1;
+            DEBUG (MTD_DEBUG_LEVEL3, "Ready: %d\n", ret);
+            return ret;
+        }
+    }
+#endif
+    emifregs    emif_addr = (emifregs)DAVINCI_ASYNC_EMIF_CNTRL_BASE;
+    return (emif_addr->NANDFSR & 0x1);
 }

+/**
+ * nand_davinci_waitfunc - [DEFAULT]  wait until the command is done
+ * @mtd:    MTD device structure
+ * @this:    NAND chip structure
+ * @state:    state to select the max. timeout value
+ *
+ * Wait for command done. This applies to erase and program only
+ * Erase can take up to 400ms and program up to 20ms according to
+ * general NAND and SmartMedia specs
+ *
+*/
 static int nand_davinci_waitfunc(struct mtd_info *mtd, struct nand_chip *this, 
int state)
 {
-    while(!nand_davinci_dev_ready(mtd)) {;}
-    *NAND_CE0CLE = NAND_STATUS;
-    return(*NAND_CE0DATA);
+    ulong start = get_timer(0);
+    volatile u_int8_t * p = (volatile u_int8_t *)((unsigned 
int)this->IO_ADDR_R);
+    unsigned long timeout = (state == FL_ERASING)? ((CFG_HZ * 400) / 1000) : 
((CFG_HZ * 20) / 1000);
+#if 0    //enable this if you don't trust your ready pin.
+    unsigned long mwait = (state == FL_ERASING)? 400 : 20;
+    udelay(mwait*1000);
+#endif
+
+    p[MASK_CLE] = NAND_CMD_STATUS;
+
+    while (1) {
+        if (get_timer(start) > timeout) {
+            printf("!!!Nand wait Timeout!!!\n");
+            return 1;
+        }
+        if (nand_davinci_dev_ready(mtd)) break;
+    }
+    return (*p);
 }

-static void nand_flash_init(void)
+#define BOOTCFG    0x01C40014
+int board_nand_init(struct nand_chip *nand)
 {
-    u_int32_t    acfg1 = 0x3ffffffc;
-    u_int32_t    acfg2 = 0x3ffffffc;
-    u_int32_t    acfg3 = 0x3ffffffc;
-    u_int32_t    acfg4 = 0x3ffffffc;
-    emifregs    emif_regs;
-
-    /*------------------------------------------------------------------*
-     *  NAND FLASH CHIP TIMEOUT @ 459 MHz                               *
-     *                                                                  *
-     *  AEMIF.CLK freq   = PLL1/6 = 459/6 = 76.5 MHz                    *
-     *  AEMIF.CLK period = 1/76.5 MHz = 13.1 ns                         *
-     *                                                                  *
-     *------------------------------------------------------------------*/
-     acfg1 = 0
+    u_int32_t acfg = 0
          | (0 << 31 )    /* selectStrobe */
          | (0 << 30 )    /* extWait */
          | (1 << 26 )    /* writeSetup    10 ns */
@@ -336,34 +290,47 @@ static void nand_flash_init(void)
          | (3 << 2 )    /* turnAround    ?? ns */
          | (0 << 0 )    /* asyncSize    8-bit bus */
          ;
+    acfg |= (*((unsigned int*)BOOTCFG)>>5)&1;    //grab default width from 
EM_WIDTH
+    /*------------------------------------------------------------------*
+     *  NAND FLASH CHIP TIMEOUT @ 459 MHz                               *
+     *                                                                  *
+     *  AEMIF.CLK freq   = PLL1/6 = 459/6 = 76.5 MHz                    *
+     *  AEMIF.CLK period = 1/76.5 MHz = 13.1 ns                         *
+     *                                                                  *
+     *------------------------------------------------------------------*/

-    emif_regs = (emifregs)DAVINCI_ASYNC_EMIF_CNTRL_BASE;
-
-    emif_regs->AWCCR |= 0x10000000;
-    emif_regs->AB1CR = acfg1;    /* 0x08244128 */;
-    emif_regs->AB2CR = acfg2;
-    emif_regs->AB3CR = acfg3;
-    emif_regs->AB4CR = acfg4;
-    emif_regs->NANDFCR = 0x00000101;
-}
+    emifregs emif_regs = (emifregs)DAVINCI_ASYNC_EMIF_CNTRL_BASE;
+    u_int32_t    addr = (u_int32_t)nand->IO_ADDR_R;
+    u_int32_t   chipNum=(addr-CFG_NAND_BASE)>>25;        //0 - cs2, 1 - cs3, 2 
- cs4, 3 - cs5
+    if (chipNum>=4) return -1;
+
+    emif_regs->AB_CR[chipNum] = acfg;    /* 0x08244128 */;
+    emif_regs->NANDFCR |= 1<<chipNum;
+
+#ifdef NAND_GPIO_READY_LIST
+    {
+        unsigned int gp = nandGpioReadyList[chipNum];
+        if (gp) {
+            unsigned int bank = (gp>>5);
+            volatile unsigned int* p = (unsigned 
int*)(DAVINCI_GPIO_BASE+GP_BANK0_OFFSET+(bank*GP_BANK_LENGTH));
+            int val;
+            int bitNum = (gp&0x1f);
+            p[GP_DIR>>2] |= 1<<bitNum;        //make sure it's an input
+            val = (p[GP_IN>>2] >> bitNum)&1;
+            DEBUG (MTD_DEBUG_LEVEL3, "Bank: %x curVal:%x inReg:%p=%x\n", 
bank,val,&p[GP_IN>>2],p[GP_IN>>2]);
+        }
+    }
+#endif

-int board_nand_init(struct nand_chip *nand)
-{
-    nand->IO_ADDR_R   = (void  __iomem *)NAND_CE0DATA;
-    nand->IO_ADDR_W   = (void  __iomem *)NAND_CE0DATA;
+    DEBUG (MTD_DEBUG_LEVEL3, "Nand base read:%p 
write:%p\n",nand->IO_ADDR_R,nand->IO_ADDR_W);
     nand->chip_delay  = 0;
     nand->select_chip = nand_davinci_select_chip;
+    nand->options = (acfg&1)? NAND_BUSWIDTH_16 : 0;
 #ifdef CFG_NAND_USE_FLASH_BBT
-    nand->options      = NAND_USE_FLASH_BBT;
+    nand->options      |= NAND_USE_FLASH_BBT;
 #endif
 #ifdef CFG_NAND_HW_ECC
-#ifdef CFG_NAND_LARGEPAGE
-    nand->eccmode     = NAND_ECC_HW12_2048;
-#elif defined(CFG_NAND_SMALLPAGE)
     nand->eccmode     = NAND_ECC_HW3_512;
-#else
-#error "Either CFG_NAND_LARGEPAGE or CFG_NAND_SMALLPAGE must be defined!"
-#endif
     nand->autooob      = &davinci_nand_oobinfo;
     nand->calculate_ecc = nand_davinci_calculate_ecc;
     nand->correct_data  = nand_davinci_correct_data;
@@ -377,9 +344,6 @@ int board_nand_init(struct nand_chip *nand)

     nand->dev_ready = nand_davinci_dev_ready;
     nand->waitfunc = nand_davinci_waitfunc;
-
-    nand_flash_init();
-
     return(0);
 }

diff --git a/include/asm-arm/arch-davinci/emif_defs.h 
b/include/asm-arm/arch-davinci/emif_defs.h
index 646fc77..d6b36da 100644
--- a/include/asm-arm/arch-davinci/emif_defs.h
+++ b/include/asm-arm/arch-davinci/emif_defs.h
@@ -29,10 +29,7 @@ typedef struct {
     dv_reg        AWCCR;
     dv_reg        SDBCR;
     dv_reg        SDRCR;
-    dv_reg        AB1CR;
-    dv_reg        AB2CR;
-    dv_reg        AB3CR;
-    dv_reg        AB4CR;
+    dv_reg        AB_CR[4];
     dv_reg        SDTIMR;
     dv_reg        DDRSR;
     dv_reg        DDRPHYCR;
@@ -51,10 +48,7 @@ typedef struct {
     dv_reg        NANDFCR;
     dv_reg        NANDFSR;
     u_int8_t    RSVD1[8];
-    dv_reg        NANDF1ECC;
-    dv_reg        NANDF2ECC;
-    dv_reg        NANDF3ECC;
-    dv_reg        NANDF4ECC;
+    dv_reg        NANDF_ECC[4];
 } emif_registers;

 typedef emif_registers    *emifregs;
diff --git a/include/asm-arm/arch-davinci/nand_defs.h 
b/include/asm-arm/arch-davinci/nand_defs.h
index 619bd47..9c324c9 100644
--- a/include/asm-arm/arch-davinci/nand_defs.h
+++ b/include/asm-arm/arch-davinci/nand_defs.h
@@ -26,136 +26,11 @@
 #ifndef _NAND_DEFS_H_
 #define _NAND_DEFS_H_

-#include <asm/arch/hardware.h>
-
 #define    MASK_CLE    0x10
-#define    MASK_ALE    0x0a
-
-#define NAND_CE0CLE    ((volatile u_int8_t *)(CFG_NAND_BASE + 0x10))
-#define NAND_CE0ALE    ((volatile u_int8_t *)(CFG_NAND_BASE + 0x0a))
-#define NAND_CE0DATA    ((volatile u_int8_t *)CFG_NAND_BASE)
-
-typedef struct  {
-    u_int32_t    NRCSR;
-    u_int32_t    AWCCR;
-    u_int8_t    RSVD0[8];
-    u_int32_t    AB1CR;
-    u_int32_t    AB2CR;
-    u_int32_t    AB3CR;
-    u_int32_t    AB4CR;
-    u_int8_t    RSVD1[32];
-    u_int32_t    NIRR;
-    u_int32_t    NIMR;
-    u_int32_t    NIMSR;
-    u_int32_t    NIMCR;
-    u_int8_t    RSVD2[16];
-    u_int32_t    NANDFCR;
-    u_int32_t    NANDFSR;
-    u_int8_t    RSVD3[8];
-    u_int32_t    NANDF1ECC;
-    u_int32_t    NANDF2ECC;
-    u_int32_t    NANDF3ECC;
-    u_int32_t    NANDF4ECC;
-    u_int8_t    RSVD4[4];
-    u_int32_t    IODFTECR;
-    u_int32_t    IODFTGCR;
-    u_int8_t    RSVD5[4];
-    u_int32_t    IODFTMRLR;
-    u_int32_t    IODFTMRMR;
-    u_int32_t    IODFTMRMSBR;
-    u_int8_t    RSVD6[20];
-    u_int32_t    MODRNR;
-    u_int8_t    RSVD7[76];
-    u_int32_t    CE0DATA;
-    u_int32_t    CE0ALE;
-    u_int32_t    CE0CLE;
-    u_int8_t    RSVD8[4];
-    u_int32_t    CE1DATA;
-    u_int32_t    CE1ALE;
-    u_int32_t    CE1CLE;
-    u_int8_t    RSVD9[4];
-    u_int32_t    CE2DATA;
-    u_int32_t    CE2ALE;
-    u_int32_t    CE2CLE;
-    u_int8_t    RSVD10[4];
-    u_int32_t    CE3DATA;
-    u_int32_t    CE3ALE;
-    u_int32_t    CE3CLE;
-} nand_registers;
-
-typedef volatile nand_registers    *nandregs;
+#define    MASK_ALE    0x08

 #define NAND_READ_START        0x00
 #define NAND_READ_END        0x30
 #define NAND_STATUS        0x70

-#ifdef CFG_NAND_HW_ECC
-#define NAND_Ecc_P1e        (1 << 0)
-#define NAND_Ecc_P2e        (1 << 1)
-#define NAND_Ecc_P4e        (1 << 2)
-#define NAND_Ecc_P8e        (1 << 3)
-#define NAND_Ecc_P16e        (1 << 4)
-#define NAND_Ecc_P32e        (1 << 5)
-#define NAND_Ecc_P64e        (1 << 6)
-#define NAND_Ecc_P128e        (1 << 7)
-#define NAND_Ecc_P256e        (1 << 8)
-#define NAND_Ecc_P512e        (1 << 9)
-#define NAND_Ecc_P1024e        (1 << 10)
-#define NAND_Ecc_P2048e        (1 << 11)
-
-#define NAND_Ecc_P1o        (1 << 16)
-#define NAND_Ecc_P2o        (1 << 17)
-#define NAND_Ecc_P4o        (1 << 18)
-#define NAND_Ecc_P8o        (1 << 19)
-#define NAND_Ecc_P16o        (1 << 20)
-#define NAND_Ecc_P32o        (1 << 21)
-#define NAND_Ecc_P64o        (1 << 22)
-#define NAND_Ecc_P128o        (1 << 23)
-#define NAND_Ecc_P256o        (1 << 24)
-#define NAND_Ecc_P512o        (1 << 25)
-#define NAND_Ecc_P1024o        (1 << 26)
-#define NAND_Ecc_P2048o        (1 << 27)
-
-#define TF(v)            (v ? 1 : 0)
-
-#define P2048e(a)        (TF(a & NAND_Ecc_P2048e) << 0)
-#define P2048o(a)        (TF(a & NAND_Ecc_P2048o) << 1)
-#define P1e(a)            (TF(a & NAND_Ecc_P1e) << 2)
-#define P1o(a)            (TF(a & NAND_Ecc_P1o) << 3)
-#define P2e(a)            (TF(a & NAND_Ecc_P2e) << 4)
-#define P2o(a)            (TF(a & NAND_Ecc_P2o) << 5)
-#define P4e(a)            (TF(a & NAND_Ecc_P4e) << 6)
-#define P4o(a)            (TF(a & NAND_Ecc_P4o) << 7)
-
-#define P8e(a)            (TF(a & NAND_Ecc_P8e) << 0)
-#define P8o(a)            (TF(a & NAND_Ecc_P8o) << 1)
-#define P16e(a)            (TF(a & NAND_Ecc_P16e) << 2)
-#define P16o(a)            (TF(a & NAND_Ecc_P16o) << 3)
-#define P32e(a)            (TF(a & NAND_Ecc_P32e) << 4)
-#define P32o(a)            (TF(a & NAND_Ecc_P32o) << 5)
-#define P64e(a)            (TF(a & NAND_Ecc_P64e) << 6)
-#define P64o(a)            (TF(a & NAND_Ecc_P64o) << 7)
-
-#define P128e(a)        (TF(a & NAND_Ecc_P128e) << 0)
-#define P128o(a)        (TF(a & NAND_Ecc_P128o) << 1)
-#define P256e(a)        (TF(a & NAND_Ecc_P256e) << 2)
-#define P256o(a)        (TF(a & NAND_Ecc_P256o) << 3)
-#define P512e(a)        (TF(a & NAND_Ecc_P512e) << 4)
-#define P512o(a)        (TF(a & NAND_Ecc_P512o) << 5)
-#define P1024e(a)        (TF(a & NAND_Ecc_P1024e) << 6)
-#define P1024o(a)        (TF(a & NAND_Ecc_P1024o) << 7)
-
-#define P8e_s(a)        (TF(a & NAND_Ecc_P8e) << 0)
-#define P8o_s(a)        (TF(a & NAND_Ecc_P8o) << 1)
-#define P16e_s(a)        (TF(a & NAND_Ecc_P16e) << 2)
-#define P16o_s(a)        (TF(a & NAND_Ecc_P16o) << 3)
-#define P1e_s(a)        (TF(a & NAND_Ecc_P1e) << 4)
-#define P1o_s(a)        (TF(a & NAND_Ecc_P1o) << 5)
-#define P2e_s(a)        (TF(a & NAND_Ecc_P2e) << 6)
-#define P2o_s(a)        (TF(a & NAND_Ecc_P2o) << 7)
-
-#define P4e_s(a)        (TF(a & NAND_Ecc_P4e) << 0)
-#define P4o_s(a)        (TF(a & NAND_Ecc_P4o) << 1)
-#endif
-
 #endif


_______________________________________________
Davinci-linux-open-source mailing list
[email protected]
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source

Reply via email to