Has anyone seen this "U-Boot 1.3.0-rc2-dirty (Sep 20 2007 - 12:41:50)" error on
the TI DVEVM? I know the rootserver is not being set but I don't know why.
IP-Config: Complete:
device=eth0, addr=192.168.0.126, mask=255.255.255.0, gw=192.168.0.1,
host=192.168.0.126, domain=, nis-domain=(none),
bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath=
Looking up port of RPC 100003/2 on 0.0.0.0
RPC: sendmsg returned error 22
portmap: RPC call returned error 22
Root-NFS: Unable to get nfsd port number from server, using default
Looking up port of RPC 100005/1 on 0.0.0.0
This is my config:
U-Boot > printenv
baudrate=115200
ethaddr=00:0e:99:02:55:0b
bootcmd=dhcp;bootm
serverip=192.168.0.114
bootfile=uImage
rootpath=/home/guest/workdir/filesys
nfshost=192.168.0.114
bootargs=console=ttyS0,115200n8 noinitrd rw ip=dhcp root=/dev/nfs nfsroot=$(nfsh
ost):$(rootpath),nolock mem=120M
rootserver=192.168.0.114
stdin=serial
stdout=serial
stderr=serial
videostd=ntsc
ver=U-Boot 1.3.0-rc2-dirty (Sep 20 2007 - 12:41:50)
Environment size: 404/16380 bytes
========Full Boot ==================================================
TI UBL Version: 1.12, Flash type: NAND
Booting PSP Boot Loader
PSPBootMode = NAND
Starting NAND Copy...
Initializing NAND flash...
Valid MagicNum found.
NAND Boot success.
DONE
U-Boot 1.3.0-rc2-dirty (Sep 20 2007 - 12:41:50)
DRAM: 256 MB
NAND: 64 MiB
In: serial
Out: serial
Err: serial
ARM Clock : 297MHz
DDR Clock : 162MHz
ETH PHY : LXT972 @ 0x01
U-Boot > printenv
baudrate=115200
ethaddr=00:0e:99:02:55:0b
bootcmd=dhcp;bootm
serverip=192.168.0.114
bootfile=uImage
rootpath=/home/guest/workdir/filesys
nfshost=192.168.0.114
bootargs=console=ttyS0,115200n8 noinitrd rw ip=dhcp root=/dev/nfs nfsroot=$(nfsh
ost):$(rootpath),nolock mem=120M
rootserver=192.168.0.114
stdin=serial
stdout=serial
stderr=serial
videostd=ntsc
ver=U-Boot 1.3.0-rc2-dirty (Sep 20 2007 - 12:41:50)
Environment size: 404/16380 bytes
U-Boot > boot
BOOTP broadcast 1
DHCP client bound to address 192.168.0.126
TFTP from server 192.168.0.114; our IP address is 192.168.0.126
Filename 'uImage'.
Load address: 0x80700000
Loading: #################################################################
###############################
done
Bytes transferred = 1408008 (157c08 hex)
## Booting image at 80700000 ...
Image Name: Linux-2.6.10_mvl401-davinci_evm
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1407944 Bytes = 1.3 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing
Linux.............................................................
Linux version 2.6.10_mvl401-davinci_evm ([EMAIL PROTECTED]) (gcc version 3.4.3
(MontaV
ista 3.4.3-25.0.30.0501131 2005-07-23)) #13 Tue Jan 30 10:13:48 MST 2007
CPU: ARM926EJ-Sid(wb) [41069265] revision 5 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
Machine: DaVinci EVM
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0,115200n8 noinitrd rw ip=dhcp root=/dev/nfs nf
sroot=$(nfshost):$(rootpath),nolock mem=120M
PID hash table entries: 512 (order: 9, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 120MB = 120MB total
Memory: 118656KB available (2412K code, 502K data, 140K init)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
spawn_desched_task(00000000)
desched cpu_callback 3/00000000
ksoftirqd started up.
desched cpu_callback 2/00000000
desched thread 0 started up.
NET: Registered protocol family 16
Registering platform device 'musb_hdrc'. Parent at platform
DaVinci I2C DEBUG: 14:57:03 Dec 26 2006
Registering platform device 'i2c'. Parent at platform
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
yaffs Dec 26 2006 14:56:02 Installing.
Registering platform device 'davincifb.0'. Parent at platform
Setting Up Clocks for DM420 OSD
Console: switching to colour frame buffer device 90x30
fb0: dm_osd0_fb frame buffer device
fb1: dm_vid0_fb frame buffer device
fb2: dm_osd1_fb frame buffer device
fb3: dm_vid1_fb frame buffer device
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
Registering platform device 'serial8250'. Parent at platform
ttyS0 at MMIO 0x1c20000 (irq = 40) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
RAMDISK driver initialized: 1 RAM disks of 32768K size 1024 blocksize
Registering platform device 'ti_davinci_emac'. Parent at platform
TI DaVinci EMAC: MAC address is 00:0e:99:02:55:0b
TI DaVinci EMAC Linux version updated 4.0
TI DaVinci EMAC: Installed 1 instances.
netconsole: not configured, aborting
i2c /dev entries driver
Linux video capture interface: v1.00
Registering platform device 'vpfe.1'. Parent at platform
DaVinci v4l2 capture driver V1.0 loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
hda: TOSHIBA MK4032GAX, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0xe10661f0-0xe10661f7,0xe10663f6 on irq 22
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB), CHS=16383/255/63
hda: hda1 hda2
ide0: BM-DMA at 0xe1066000-0xe1066007, BIOS settings: hda:pio, hdb:pio
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI SIO
drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI 8U232AM
Compatible
drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI FT232BM
Compatible
drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI FT2232C
Compatible
drivers/usb/serial/usb-serial.c: USB Serial support registered for USB-UIRT Infr
ared Tranceiver
drivers/usb/serial/usb-serial.c: USB Serial support registered for Home-Electron
ics TIRA-1 IR Transceiver
usbcore: registered new driver ftdi_sio
drivers/usb/serial/ftdi_sio.c: v1.4.1:USB FTDI Serial Converters Driver
mice: PS/2 mouse device common for all mice
musb_hdrc: version 2.2a/db-0.4.8 [pio] [host] [debug=3]
musb_hdrc: USB Host mode controller at c8060000 using PIO, IRQ 12
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Bluetooth: HCI USB driver ver 2.7
usbcore: registered new driver hci_usb
Bluetooth: HCI UART driver ver 2.1
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Registering platform device 'davinci-audio.0'. Parent at platform
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET: Registered protocol family 1
NET: Registered protocol family 17
Bluetooth: L2CAP ver 2.6
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.3
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.2
usb 1-1: new full speed USB device using musb_hdrc and address 2
usb 1-1: Product: BCM92045B3 ROM
usb 1-1: Manufacturer: Broadcom Corp
Sending DHCP requests ..,. OK
IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.0.126
IP-Config: Complete:
device=eth0, addr=192.168.0.126, mask=255.255.255.0, gw=192.168.0.1,
host=192.168.0.126, domain=, nis-domain=(none),
bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath=
Looking up port of RPC 100003/2 on 0.0.0.0
RPC: sendmsg returned error 22
portmap: RPC call returned error 22
Root-NFS: Unable to get nfsd port number from server, using default
Looking up port of RPC 100005/1 on 0.0.0.0
RPC: sendmsg returned error 22
portmap: RPC call returned error 22
Root-NFS: Unable to get mountd port number from server, using default
RPC: sendmsg returned error 22
mount: RPC call returned error 22
Root-NFS: Server returned error -22 while mounting /tftpboot/$(nfshost):$(rootpa
th)
VFS: Unable to mount root fs via NFS, trying floppy.
VFS: Cannot open root device "nfs" or unknown-block(2,0)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)
---------------------------------
Catch up on fall's hot new shows on Yahoo! TV. Watch previews, get listings,
and more!_______________________________________________
Davinci-linux-open-source mailing list
[email protected]
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
