I think I see the problem here.
Your failure is:
mount: server 10.100.21.95 not responding, timed out
Root-NFS: Server returned error -5 while mounting
and the reason is most likely because your configured IP address is
192.168.1.101
You can't reach your server from your IP address. They need to be in the
same address ranges.
Go to the configuration on your router and either turn off DHCP and let
your 10.100 domain configure your IP address (are you running DHCP on
the PC?)
OR statically configure an IP for your eval board (ip = 10.100.21.xxx).
[EMAIL PROTECTED] wrote:
Hello
Thanks for all your help previously and on this question.
I'm having problems getting my DM355 EVM to boot through the NFS setup.
I have followed the TI SPRUF73 guide through section 4.3.5
Wanted to explain my setup first and then display my failure message with
the printenv setup also
1) My setup is a PC running Red Hat Enterprise Linux WS release 4.
This is straight ethernet cabled into a Linksys Router BEFW11S4. It
happens to be a wireless router but I'm just using the 4 ethernet ports
on the back. The PC is hooked into port 1.
I hook the EVM board into port 2 with a straight ethernet cable.
2) My EVM printenv
bootdelay=3
baudrate=115200
bootfile="uImage"
bootcmd=nboot 0x80700000 0 0x400000; bootm
rootpath=/home/gellerbusch/workdir/filesys
nfshost=10.100.21.95
bootargs=console=ttyS0,115200n8 noinitrd rw ip=dhcp root=/dev/nfs
nfsroot=10.100
.21.95:/home/gellerbusch/workdir/filesys,nolock mem=116M
stdin=serial
stdout=serial
stderr=serial
videostd=ntsc
3) A snippet of the boot failure.
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
eth0: link down
Sending DHCP requests ..<6>eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
, OK
IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.1.101
IP-Config: Complete:
device=eth0, addr=192.168.1.101, mask=255.255.255.0, gw=192.168.1.1,
host=192.168.1.101, domain=, nis-domain=(none),
bootserver=0.0.0.0, rootserver=10.100.21.95, rootpath=
Looking up port of RPC 100003/2 on 10.100.21.95
portmap: server 10.100.21.95 not responding, timed out
Root-NFS: Unable to get nfsd port number from server, using default
Looking up port of RPC 100005/1 on 10.100.21.95
portmap: server 10.100.21.95 not responding, timed out
Root-NFS: Unable to get mountd port number from server, using default
mount: server 10.100.21.95 not responding, timed out
Root-NFS: Server returned error -5 while mounting
/home/gellerbusch/workdir/file
sys
VFS: Unable to mount root fs via NFS, trying floppy.
VFS: Cannot open root device "nfs" or unknown-block(2,0)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(2,0)
Any thoughts.
Thanks,
GARY ELLERBUSCH
HORIBA JOBIN YVON
_______________________________________________
Davinci-linux-open-source mailing list
[email protected]
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
_______________________________________________
Davinci-linux-open-source mailing list
[email protected]
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
