Thanks Phill Unfortunately there is no possibility to set video outputs via bootargs. I can change sources. But now I have no signal on all outputs. Really funny is that, I have tested the whole DEMO one week ago. It works. Than I was away. Monday I returned to work and I have no signal. Ondrej Pindroch SoftHard Technology ltd.
-----Original Message----- From: "Phil Quiney" <[EMAIL PROTECTED]> To: "Ondrej Pindroch" <[EMAIL PROTECTED]>, <[email protected]> Date: Tue, 12 Aug 2008 10:08:24 +0100 Subject: RE: DVEVM 6467 no signal on output Hi, The 'kernel taint' messages are normal for the dsplinkk module and are caused by the fact that it is not GPL code.They are harmless - the module has loaded and should still function. I would check your boot arguments - I would have expected a xxxxx=component (where xxxxx is some module parameter or other) in the boot line or is it the default on the 6467 (I don't have a 6467 board to try here)? Just checking your kernel output and it says 'ch0 default output "COMPOSITE", mode "NTSC"' which backs up this idea. Regards Phil Q Phil Quiney, Senior Software Engineer Trinity Convergence Cambridge Business Park Cowley Road Cambridge CB4 0WZ, UK T: +44(0)1223-435536 F: +44(0)1223-435560 www.trinityconvergence.com [http://www.trinityconvergence.com/] From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf OfOndrej Pindroch Sent: 11 August 2008 14:12 To: [email protected] Subject: DVEVM 6467 no signal on output Hi All I have had working demo on DVEVM 6467. I was booting from TFTP and all was OK. This monday I turned on DVEVM and monitor displayed. that no signal is on component input. This is listing of booting: Booting PSP Boot Loader Starting NAND Copy Booting Application @ 0x81080000 U-Boot 1.2.0 (Dec 13 2007 - 14:52:18) I2C: ready DRAM: 256 MB unknown vendor=0 Flash: 0 kB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock :- 297MHz DDR Clock :- 297MHz Hit any key to stop autoboot: 0 BOOTP broadcast 1 DHCP client bound to address 192.168.0.248 TFTP from server 192.168.0.228; our IP address is 192.168.0.248 Filename 'uImage'. Load address: 0x80700000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################# done Bytes transferred = 1496728 (16d698 hex) ## Booting image at 80700000 ... Image Name: Linux-2.6.10_mvl401-davinci_evm- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1496664 Bytes = 1.4 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................. ....................................... done, booting the kernel. Linux version 2.6.10_mvl401-davinci_evm-PSP_01_30_00_070 ([EMAIL PROTECTED] main) (gcc version 3.4.3 (MontaVista 3.4.3-25.0.30.0501131 2005-07-23)) #1 Wed J ul 9 01:33:51 CEST 2008 CPU: ARM926EJ-Sid(wb) [41069265] revision 5 (ARMv5TEJ) CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets Machine: DaVinci DM6467 EVM Memory policy: ECC disabled, Data cache writeback DM6467 Built 1 zonelists Kernel command line: console=ttyS0,115200n8 root=/dev/hda1 rw noinitrd ip=dhcp m em=120M davincihd_capture.channel0_numbuffers=4 PID hash table entries: 512 (order: 9, 8192 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 120MB = 120MB total Memory: 118272KB available (2555K code, 531K data, 164K init) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok spawn_desched_task(00000000) desched cpu_callback 3/00000000 ksoftirqd started up. desched cpu_callback 2/00000000 desched thread 0 started up. NET: Registered protocol family 16 DaVinci: 48 gpio irqs Registering platform device 'serial8250.0'. Parent at platform Registering platform device 'musb_hdrc'. Parent at platform DaVinci I2C DEBUG: 01:32:10 Jul 9 2008 Registering platform device 'i2c'. Parent at platform ch0 default output "COMPOSITE", mode "NTSC" ch1 default output "", mode "" SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub musb_hdrc: version 2.2a/db-0.4.8 [cppi-dma] [host] [debug=0] musb_hdrc: ConfigData=0x06 (UTMI-8, dyn FIFOs, SoftConn) musb_hdrc: MHDRC RTL version 1.500 musb_hdrc: USB Host mode controller at c8000000 using DMA, IRQ 13 musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc. yaffs Jul 9 2008 01:31:48 Installing. Registering platform device 'DavinciHD_vdce.2'. Parent at platform enable_irq(12) unbalanced from c0023860 CIR device registered successfully (Major = 253, Minor = 0)<6>Registering platform device 'cir.0'. Parent at platform Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled Registering platform device 'serial8250'. Parent at platform ttyS0 at MMIO 0x1c20000 (irq = 40) is a ST16654 ttyS1 at MMIO 0x1c20400 (irq = 41) is a ST16650V2 io scheduler noop registered io scheduler anticipatory registered RAMDISK driver initialized: 1 RAM disks of 32768K size 1024 blocksize Registering platform device 'ti_davinci_emac'. Parent at platform TI DaVinci EMAC: MAC address is 00:0e:99:02:b2:67 TI DaVinci EMAC Linux version updated 5.0 TI DaVinci EMAC: Installed 1 instances. netconsole: not configured, aborting i2c /dev entries driver Linux video capture interface: v1.00 Registering platform device 'vpif capture.1'. Parent at platform Registering platform device 'vpif display.1'. Parent at platform Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx MUX: initialized ATAEN hda: TOSHIBA MK4032GAX, ATA DISK drive elevator: using anticipatory as default io scheduler ide0 at 0xe10661f0-0xe10661f7,0xe10663f6 on irq 22 hda: max request size: 1024KiB hda: 78140160 sectors (40007 MB), CHS=16383/255/63 hda: hda1 hda2 ide0: BM-DMA at 0xe1066000-0xe1066007, BIOS settings: hda:pio, hdb:pio Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice Registering Audio Devices. Total communication peripherals (ASP) : 2 Codec with ID = 0 on ASP = 0 is initialized.Using minor number : 3 Configuring the McASP as Master Configuring the McASP 1 for DIT SPDIF on ASP = 1 isinitialized.Using minor number : 19 NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 8192 bind 16384) NET: Registered protocol family 1 NET: Registered protocol family 17 Sending DHCP requests ., OK IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.0.248 IP-Config: Complete: device=eth0, addr=192.168.0.248, mask=255.255.255.0, gw=192.168.0.128, host=192.168.0.248, domain=sht.local, nis-domain=(none), bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on hda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem). Freeing init memory: 164K INIT: version 2.85 booting Mounting a tmpfs over /dev...done. Creating initial device nodes...done. Activating swap...done. Remounting root filesystem...done. Calculating module dependencies Loading modules: Checking all file systems: fsck fsck 1.35 (28-Feb-2004) Mounting local filesystems: mount relayfs on /mnt/relayfs type relayfs (rw) Cleaning: /tmp /var/lock /var/run done. Setting up networking (ifupdown) .. Cleaning: /etc/network/run/ifstate done. Starting network interfaces: done. Starting hotplug subsystem: pci pci [success] usb usb [success] isapnp isapnp [success] ide ide [success] input input [success] scsi scsi [success] done. Starting portmap daemon: portmap. done. Setting pseudo-terminal access permissions...done. Updating /etc/motd...done. INIT: Entering runlevel: 3 Starting NFS common utilities: statd lockd. Starting internet superserver: inetd. ioremap_nocache(0x87800000, 69206016)=0xc8100000 allocated heap buffer 0xc8100000 of size 0x821000 cmem initialized 5 pools between 0x87800000 and 0x8ba00000 dsplinkk: no version for "struct_module" found: kernel tainted. dsplinkk: module license 'DSP/BIOS(TM) LINK' taints kernel. DSPLINK Module (1.50) created on Date: Jan 3 2008 Time: 13:16:55 Starting web server ... thttpd Starting MontaVista target tools daemon: mvltdmvltd version 2.1 MontaVista Softw are,Inc. mvltd[1120]: started on port 34577 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver . MontaVista(R) Linux(R) Professional Edition 4.0.1 (0600980) 192.168.0.248 login: I am especially interested in two underlined lines.Ondrej Pindroch SoftHard Technology ltd.
_______________________________________________ Davinci-linux-open-source mailing list [email protected] http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
