Hi Venkat, I checked that it is not running.. rc.d scrips is not at all there When I searched it through locate
Even I tried later Booting from flash Using the EVM's hard drive file system (this time interface was runnig but demo did not start) Then following is the result Starting portmap daemon: portmap. done. Setting pseudo-terminal access permissions...done. Updating /etc/motd...done. INIT: Entering runlevel: 3 Starting NFS common utilities: statd lockd. Starting internet superserver: inetd. ioremap_nocache(0x87800000, 69206016)=0xc8080000 allocated heap buffer 0xc8080000 of size 0xefc000 cmem initialized 5 pools between 0x87800000 and 0x8ba00000 dsplinkk: no version for "struct_module" found: kernel tainted. dsplinkk: module license 'DSP/BIOS(TM) LINK' taints kernel. DSPLINK Module (1.50.00.04) created on Date: Nov 13 2007 Time: 11:55:30 Starting web server ... thttpd Starting MontaVista target tools daemon: mvltdmvltd version 2.1 MontaVista Softw are,Inc. ipv6: disagrees about version of symbol struct_module modprobe: FATAL: Error inserting ipv6 (/lib/modules/2.6.10_mvl401-davinci_evm/ke rnel/net/ipv6/ipv6.ko): Invalid module format ipv6: disagrees about version of symbol struct_module modprobe: FATAL: Error inserting ipv6 (/lib/modules/2.6.10_mvl401-davinci_evm/ke rnel/net/ipv6/ipv6.ko): Invalid module format mvltd[1090]: started on port 34577 Regards Prashanth Regards Prashanth -----Original Message----- From: Venkatachala Upadhya [mailto:[EMAIL PROTECTED] Sent: Wednesday, October 15, 2008 10:23 AM To: Prashantha Gowda; [email protected] Subject: RE: Demo on DVEVM 6467 is not starting Hello, Generally, when the board boots up, the interface demo is also started, unless this is disabled during the boot in the rc.d scripts. Verify if this is the cause. You can use the command below to know if the interface demo is already getting executed. ps -ef | grep interface With best regards, Venkatachala Upadhya| Extn: 65395| -- -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Prashantha Gowda Sent: 14 October, 2008 8:22 PM To: [email protected] Subject: Demo on DVEVM 6467 is not starting Hi all I have build whole demo on DVEVM 6467 but I am still not able to run it. This is what i get, when I tried to lounche decode. [EMAIL PROTECTED]:/opt/dvsdk/dm6467# ./decode -y5 -o -i -v ./data/videos/dust_1080i_30fps.m2v Decode demo started. Error: Failed to create display device Error: Failed to create Cpu Object Demo interface started at level 4. Interface Error: Failed to create display device instance Have you any sugestion, what to do? _______________________________________________ Davinci-linux-open-source mailing list [email protected] http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source This message (including attachment if any) is confidential and may be privileged. If you have received this message by mistake please notify the sender by return e-mail and delete this message from your system. Any unauthorized use or dissemination of this message in whole or in part is strictly prohibited. E-mail may contain viruses. Before opening attachments please check them for viruses and defects. While MindTree Limited (MindTree) has put in place checks to minimize the risks, MindTree will not be responsible for any viruses or defects or any forwarded attachments emanating either from within MindTree or outside. Please note that e-mails are susceptible to change and MindTree shall not be liable for any improper, untimely or incomplete transmission. MindTree reserves the right to monitor and review the content of all messages sent to or from MindTree e-mail address. Messages sent to or from this e-mail address may be stored on the MindTree e-mail system or else where. _______________________________________________ Davinci-linux-open-source mailing list [email protected] http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
