Previous to updating codec engine (I was on 2.00 now on 2.10) I could launch
and debug my ARM code with GDB debugger. However now whenever I try to
launch it fails. Setting CE_DEBUG=3 this is my output.
@1,540,122us: [+2 T:0x424ccb60 S:0x424cc52c] OP - Processor_create_d> Adding
DSP segment #0 to Link configuration: name='DDR2', startAddress=0x87800000,
sizeInBytes=0x400000, shared=1
@1,540,472us: [+2 T:0x424ccb60 S:0x424cc52c] OP - Processor_create_d> Adding
DSP segment #1 to Link configuration: name='DSPLINKMEM',
startAddress=0x87c00000, sizeInBytes=0x200000, shared=1
@1,540,821us: [+2 T:0x424ccb60 S:0x424cc52c] OP - Processor_create_d> Adding
DSP segment #2 to Link configuration: name='RESET_VECTOR',
startAddress=0x87e00000, sizeInBytes=0x80, shared=0
@1,541,223us: [+2 T:0x424ccb60 S:0x424cc52c] OP - Processor_create_d> Adding
DSP segment #3 to Link configuration: name='DDRALGHEAP',
startAddress=0x84600000, sizeInBytes=0x3200000, shared=0
@1,541,562us: [+2 T:0x424ccb60 S:0x424cc52c] OP - Processor_create_d>
DOPOWERCONTROL was=0; now=0
@1,546,925us: [+2 T:0x424ccb60 S:0x424cc52c] OP - Processor_create_d>
Attachingto DSP PROC...
[New Thread 1120717664 (LWP 1353)]
@1,638,860us: [+0 T:0x4041f2c8 S:0xbefff19c] ti.sdo.ce.osal.Sem - Leaving
Sem_pend> sem[0x418320] status[0]
@1,639,322us: [+0 T:0x4041f2c8 S:0xbefff1bc] OP - doCmd> Exit (result=0)
@1,639,727us: [+0 T:0x4041f2c8 S:0xbefff1cc] OP - Processor_delete>
Enter(proc=0x418620)
@1,639,993us: [+1 T:0x4041f2c8 S:0xbefff1cc] OP - Processor_delete(0x418620)
freeing object ...
@1,640,251us: [+0 T:0x4041f2c8 S:0xbefff1a4] OM - Memory_free>
Enter(0x418620, 0x24)
@1,640,510us: [+0 T:0x4041f2c8 S:0xbefff1a4] OM - Memory_free> return (0x1)
@1,640,741us: [+0 T:0x4041f2c8 S:0xbefff1dc] OP - Processor_delete> return.
@1,641,025us: [+6 T:0x4041f2c8 S:0xbefff214] CE - rserverOpen: can't start
'SARalgo.x64P'; Processor_create failed
@1,641,302us: [+0 T:0x4041f2c8 S:0xbefff214] CE -
rserverOpen('SARalgo.x64P'): 0x0 done.
Does anybody see anything suspicious? Or know about this problem?
Thanks,
Josh
_______________________________________________
Davinci-linux-open-source mailing list
[email protected]
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
