U-Boot 1.1.4 (Aug 9 2008 - 11:10:18) U-Boot code: 81080000 -> 8109AAEC BSS: -> 810A3558 RAM Configuration: Bank #0: 80000000 256 MB unknown vendor=0 Flash: 0 kB NAND:64 MB In: serial Out: serial Err: serial ARM Clock :- 297MHz DDR Clock :- 162MHz I2C read: I/O error I2C write: I/O error I2C read: I/O error MSP430 Firmware does not support AM/PM Feature Hit any key to stop autoboot: 0 TFTP from server 192.168.55.61; our IP address is 192.168.55.28 Filename 'uImage_R*'. Load address: 0x80700000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################################### done Bytes transferred = 1846256 (1c2bf0 hex) ## Booting image at 80700000 ... Image Name: Linux-2.6.31-rc4 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1846192 Bytes = 1.8 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux.......................................................................................................................... done, booting . Linux version 2.6.31-rc4 (hailing@hailing-desktop) (gcc version 3.4.3 (MontaVista 3.4.3-25.0.104.0600975 2006-07-06)) #1 PREEMPT Mon Jul 27 09:54:52 CST 2009 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DM644x EVM Memory policy: ECC disabled, Data cache writeback DaVinci dm6446 variant 0x0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 30480 Kernel command line: video=davincifb:vid0=720x570x16,2500K:vid1=720x570x16,2500K:osd0=720x570x16,2025K davinci_enc_mngr.ch0_output=COMPOSITE davinci_enc_mngM Unknown boot option `davinci_enc_mngr.ch0_output=COMPOSITE': ignoring Unknown boot option `davinci_enc_mngr.ch0_mode=pal': ignoring PID hash table entries: 512 (order: 9, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 120MB = 120MB total Memory: 117716KB available (3512K code, 263K data, 140K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:168 Console: colour dummy device 80x30 Calibrating delay loop... 147.86 BogoMIPS (lpj=739328) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 71 gpio irqs NET: Registered protocol family 16 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb musb_hdrc: version 6.0, cppi-dma, host, debug=0 Platform driver 'musb_hdrc' needs updating - please use dev_pm_ops NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. msgmni has been set to 230 io scheduler noop registered io scheduler anticipatory registered (default) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled Platform driver 'serial8250' needs updating - please use dev_pm_ops serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a 16550A console [ttyS0] enabled serial8250 serial8250.0: unable to register port at index 1 (IO0 MEM1c20400 IRQ41): -22 serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1c20800 IRQ42): -22 brd: module loaded loop: module loaded Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 davinci_emac_probe: using random MAC addr: 5a:f2:45:c3:94:75 emac-mii: probed console [netcon0] enabled netconsole: network logging started NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit) Bad block table not found for chip 0 Bad block table not found for chip 0 Scanning device for bad blocks Bad eraseblock 0 at 0x000000000000 Bad eraseblock 1 at 0x000000004000 Bad eraseblock 2 at 0x000000008000 Bad eraseblock 3 at 0x00000000c000 Bad eraseblock 4 at 0x000000010000 Bad eraseblock 5 at 0x000000014000 Bad eraseblock 6 at 0x000000018000 . ... .. ....... . ... .. ....... . ... .. ....... Bad eraseblock 4092 at 0x000003ff0000 Bad eraseblock 4093 at 0x000003ff4000 Bad eraseblock 4094 at 0x000003ff8000 Bad eraseblock 4095 at 0x000003ffc000 No space left to write bad block table davinci_nand: probe of davinci_nand.0 failed with error -28 usbmon: debugfs is not available Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. Platform driver 'dummy_hcd' needs updating - please use dev_pm_ops Platform driver 'dummy_udc' needs updating - please use dev_pm_ops dummy_hcd dummy_hcd: USB Host+Gadget Emulator, driver 02 May 2005 dummy_hcd dummy_hcd: Dummy host controller dummy_hcd dummy_hcd: new USB bus registered, assigned bus number 1 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected mice: PS/2 mouse device common for all mice i2c /dev entries driver watchdog watchdog: heartbeat 60 sec usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. lib80211: common routines for IEEE802.11 drivers eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=1:01, id=8201) ADDRCONF(NETDEV_UP): eth0: link is not ready IP-Config: Complete: device=eth0, addr=192.168.55.28, mask=255.255.255.0, gw=192.168.55.1, host=192.168.55.28, domain=, nis-domain=(none), bootserver=192.168.55.61, rootserver=192.168.55.61, rootpath= Looking up port of RPC 100003/2 on 192.168.55.61 PHY: 1:01 - Link is Up - 100/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Looking up port of RPC 100005/1 on 192.168.55.61 VFS: Mounted root (nfs filesystem) on device 0:13. Freeing init memory: 140K INIT: version 2.85 booting Mounting a tmpfs over /dev...done. Creating initial device nodes...done. Activating swap...done. Remounting root filesystem...done. Calculating module dependencies Loading modules: Checking all file systems: fsck fsck 1.35 (28-Feb-2004) Mounting local filesystems: mount nothing was mounted Cleaning: /tmp /var/lock /var/run done. Setting up networking (ifupdown) .. Cleaning: /etc/network/run/ifstate done. Starting network interfaces: done. Starting hotplug subsystem: pci pci [success] usb usb [success] isapnp isapnp [success] ide ide [success] input input [success] scsi scsi [success] done. Starting portmap daemon: portmapportmap: fork: Success. done. Updating /etc/motd...