This patch adds initial support for the MityDSP-L138 and MityDSP-1808 system on Module (SOM) under the machine name "mityomapl138". These SOMs are based on the da850 davinci CPU architecture. Information on these SOMs may be found at http://www.mitydsp.com.
Basic support for the console UART, NAND, and EMAC (MII interface) is included in this patch. Signed-off-by: Michael Williamson <[email protected]> --- Patch is against 0a50e05b20f3c6af67656303bdb3661a2541ce03 of Kevin's tree (2.6.36-rc2). Changes since v0: 1) Added CONFIG_REGULATOR_DUMMY to da8xx_omapl_defconfig to support DA8XX machines not providing voltage regulation. 2) Added machine checks on da830/da850 EVM as well as MityDSP-L138 console init routines. 3) Defaulted MACH_MITYOMAPL138 on for ARCH_DAVINCI_DA850 selection in KConfig. 4) Fixed comment block whitespace violation. (Elected to leave the default NAND partition as is) arch/arm/configs/da8xx_omapl_defconfig | 1 + arch/arm/mach-davinci/Kconfig | 9 + arch/arm/mach-davinci/Makefile | 1 + arch/arm/mach-davinci/board-da830-evm.c | 3 + arch/arm/mach-davinci/board-da850-evm.c | 3 + arch/arm/mach-davinci/board-mityomapl138.c | 220 +++++++++++++++++++++++ arch/arm/mach-davinci/include/mach/uncompress.h | 1 + 7 files changed, 238 insertions(+), 0 deletions(-) diff --git a/arch/arm/configs/da8xx_omapl_defconfig b/arch/arm/configs/da8xx_omapl_defconfig index ba66705..3952a4e 100644 --- a/arch/arm/configs/da8xx_omapl_defconfig +++ b/arch/arm/configs/da8xx_omapl_defconfig @@ -79,6 +79,7 @@ CONFIG_I2C_DAVINCI=y # CONFIG_HWMON is not set CONFIG_WATCHDOG=y CONFIG_REGULATOR=y +CONFIG_REGULATOR_DUMMY=y CONFIG_REGULATOR_TPS6507X=y CONFIG_FB=y CONFIG_FB_DA8XX=y diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig index 2bf03e9..633eccb 100644 --- a/arch/arm/mach-davinci/Kconfig +++ b/arch/arm/mach-davinci/Kconfig @@ -185,6 +185,15 @@ config MACH_TNETV107X help Say Y here to select the TI TNETV107X Evaluation Module. +config MACH_MITYOMAPL138 + bool "Critical Link MityDSP-L138/MityARM-1808 SoM" + default ARCH_DAVINCI_DA850 + depends on ARCH_DAVINCI_DA850 + help + Say Y here to select the Critical Link MityDSP-L138/MityARM-1808 + System on Module. Information on this SoM may be found at + http://www.mitydsp.com + config DAVINCI_MUX bool "DAVINCI multiplexing support" depends on ARCH_DAVINCI diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile index eab4c0f..3e966e8 100644 --- a/arch/arm/mach-davinci/Makefile +++ b/arch/arm/mach-davinci/Makefile @@ -33,6 +33,7 @@ obj-$(CONFIG_MACH_DAVINCI_DM365_EVM) += board-dm365-evm.o obj-$(CONFIG_MACH_DAVINCI_DA830_EVM) += board-da830-evm.o obj-$(CONFIG_MACH_DAVINCI_DA850_EVM) += board-da850-evm.o obj-$(CONFIG_MACH_TNETV107X) += board-tnetv107x-evm.o +obj-$(CONFIG_MACH_MITYOMAPL138) += board-mityomapl138.o # Power Management obj-$(CONFIG_CPU_FREQ) += cpufreq.o diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c index 292e8b7..e51a80f 100644 --- a/arch/arm/mach-davinci/board-da830-evm.c +++ b/arch/arm/mach-davinci/board-da830-evm.c @@ -586,6 +586,9 @@ static __init void da830_evm_init(void) #ifdef CONFIG_SERIAL_8250_CONSOLE static int __init da830_evm_console_init(void) { + if (!machine_is_davinci_da830_evm()) + return 0; + return add_preferred_console("ttyS", 2, "115200"); } console_initcall(da830_evm_console_init); diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index 190ebd3..d491b5f 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -847,6 +847,9 @@ static __init void da850_evm_init(void) #ifdef CONFIG_SERIAL_8250_CONSOLE static int __init da850_evm_console_init(void) { + if (!machine_is_davinci_da850_evm()) + return 0; + return add_preferred_console("ttyS", 2, "115200"); } console_initcall(da850_evm_console_init); diff --git a/arch/arm/mach-davinci/board-mityomapl138.c b/arch/arm/mach-davinci/board-mityomapl138.c new file mode 100644 index 0000000..7338adb --- /dev/null +++ b/arch/arm/mach-davinci/board-mityomapl138.c @@ -0,0 +1,220 @@ +/* + * Critical Link MityOMAP-L138 SoM + * + * Copyright (C) 2010 Critical Link LLC - http://www.criticallink.com + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of + * any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/console.h> +#include <linux/platform_device.h> +#include <linux/mtd/partitions.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <mach/common.h> +#include <mach/cp_intc.h> +#include <mach/da8xx.h> +#include <mach/nand.h> +#include <mach/mux.h> + +#define MITYOMAPL138_PHY_MASK 0x08 /* hardcoded for now */ +#define MITYOMAPL138_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ + +/* + * MityDSP-L138 includes a 256 MByte large-page NAND flash + * (128K blocks). + */ +struct mtd_partition mityomapl138_nandflash_partition[] = { + { + .name = "rootfs", + .offset = 0, + .size = SZ_128M, + .mask_flags = 0, /* MTD_WRITEABLE, */ + }, + { + .name = "homefs", + .offset = MTDPART_OFS_APPEND, + .size = MTDPART_SIZ_FULL, + .mask_flags = 0, + }, +}; + +static struct davinci_nand_pdata mityomapl138_nandflash_data = { + .parts = mityomapl138_nandflash_partition, + .nr_parts = ARRAY_SIZE(mityomapl138_nandflash_partition), + .ecc_mode = NAND_ECC_HW, + .options = NAND_USE_FLASH_BBT | NAND_BUSWIDTH_16, + .ecc_bits = 1, /* 4 bit mode is not supported with 16 bit NAND */ +}; + +static struct resource mityomapl138_nandflash_resource[] = { + { + .start = DA8XX_AEMIF_CS3_BASE, + .end = DA8XX_AEMIF_CS3_BASE + SZ_512K + 2 * SZ_1K - 1, + .flags = IORESOURCE_MEM, + }, + { + .start = DA8XX_AEMIF_CTL_BASE, + .end = DA8XX_AEMIF_CTL_BASE + SZ_32K - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device mityomapl138_nandflash_device = { + .name = "davinci_nand", + .id = 0, + .dev = { + .platform_data = &mityomapl138_nandflash_data, + }, + .num_resources = ARRAY_SIZE(mityomapl138_nandflash_resource), + .resource = mityomapl138_nandflash_resource, +}; + +static struct platform_device *mityomapl138_devices[] __initdata = { + &mityomapl138_nandflash_device, +}; + +static void __init mityomapl138_setup_nand(void) +{ + platform_add_devices(mityomapl138_devices, + ARRAY_SIZE(mityomapl138_devices)); +} + +static struct davinci_uart_config mityomapl138_uart_config __initdata = { + .enabled_uarts = 0x7, +}; + +static const short mityomap_mii_pins[] = { + DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3, + DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER, + DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3, + DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK, + DA850_MDIO_D, + -1 +}; + +static const short mityomap_rmii_pins[] = { + DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN, + DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1, + DA850_RMII_RXER, DA850_RMII_MHZ_50_CLK, DA850_MDIO_CLK, + DA850_MDIO_D, + -1 +}; + +static void __init mityomapl138_config_emac(void) +{ + void __iomem *cfg_chip3_base; + int ret; + u32 val; + struct davinci_soc_info *soc_info = &davinci_soc_info; + soc_info->emac_pdata->rmii_en = 0; /* hardcoded for now */ + + cfg_chip3_base = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG); + val = __raw_readl(cfg_chip3_base); + + if (soc_info->emac_pdata->rmii_en) { + val |= BIT(8); + ret = davinci_cfg_reg_list(mityomap_rmii_pins); + pr_info("RMII PHY configured\n"); + } else { + val &= ~BIT(8); + ret = davinci_cfg_reg_list(mityomap_mii_pins); + pr_info("MII PHY configured\n"); + } + + if (ret) { + pr_warning("mii/rmii mux setup failed: %d\n", ret); + return; + } + + /* configure the CFGCHIP3 register for RMII or MII */ + __raw_writel(val, cfg_chip3_base); + + soc_info->emac_pdata->phy_mask = MITYOMAPL138_PHY_MASK; + pr_info("setting phy_mask to %x\n", soc_info->emac_pdata->phy_mask); + soc_info->emac_pdata->mdio_max_freq = MITYOMAPL138_MDIO_FREQUENCY; + + ret = da8xx_register_emac(); + if (ret) + pr_warning("emac registration failed: %d\n", ret); +} + +static struct davinci_pm_config da850_pm_pdata = { + .sleepcount = 128, +}; + +static struct platform_device da850_pm_device = { + .name = "pm-davinci", + .dev = { + .platform_data = &da850_pm_pdata, + }, + .id = -1, +}; + +static void __init mityomapl138_init(void) +{ + int ret; + + /* for now, no special EDMA channels are reserved */ + ret = da850_register_edma(NULL); + if (ret) + pr_warning("edma registration failed: %d\n", ret); + + ret = da8xx_register_watchdog(); + if (ret) + pr_warning("watchdog registration failed: %d\n", ret); + + davinci_serial_init(&mityomapl138_uart_config); + + mityomapl138_setup_nand(); + + mityomapl138_config_emac(); + + ret = da8xx_register_rtc(); + if (ret) + pr_warning("rtc setup failed: %d\n", ret); + + ret = da850_register_cpufreq("pll0_sysclk3"); + if (ret) + pr_warning("cpufreq registration failed: %d\n", ret); + + ret = da8xx_register_cpuidle(); + if (ret) + pr_warning("cpuidle registration failed: %d\n", ret); + + ret = da850_register_pm(&da850_pm_device); + if (ret) + pr_warning("da850_evm_init: suspend registration failed: %d\n", + ret); +} + +#ifdef CONFIG_SERIAL_8250_CONSOLE +static int __init mityomapl138_console_init(void) +{ + if (!machine_is_mityomapl138()) + return 0; + + return add_preferred_console("ttyS", 1, "115200"); +} +console_initcall(mityomapl138_console_init); +#endif + +static void __init mityomapl138_map_io(void) +{ + da850_init(); +} + +MACHINE_START(MITYOMAPL138, "MityDSP-L138/MityARM-1808") + .phys_io = IO_PHYS, + .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, + .boot_params = (DA8XX_DDR_BASE + 0x100), + .map_io = mityomapl138_map_io, + .init_irq = cp_intc_init, + .timer = &davinci_timer, + .init_machine = mityomapl138_init, +MACHINE_END diff --git a/arch/arm/mach-davinci/include/mach/uncompress.h b/arch/arm/mach-davinci/include/mach/uncompress.h index 15a6192..d370391 100644 --- a/arch/arm/mach-davinci/include/mach/uncompress.h +++ b/arch/arm/mach-davinci/include/mach/uncompress.h @@ -88,6 +88,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id) /* DA8xx boards */ DEBUG_LL_DA8XX(davinci_da830_evm, 2); DEBUG_LL_DA8XX(davinci_da850_evm, 2); + DEBUG_LL_DA8XX(mityomapl138, 1); /* TNETV107x boards */ DEBUG_LL_TNETV107X(tnetv107x, 1); _______________________________________________ Davinci-linux-open-source mailing list [email protected] http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
