On Fri, Jan 25, 2013 at 16:52:18, Nori, Sekhar wrote: > On 1/25/2013 4:34 PM, Katepallewar, Mrugesh wrote: > > On Fri, Jan 25, 2013 at 16:04:22, Nori, Sekhar wrote: > >> On 1/25/2013 11:43 AM, Mrugesh Katepallewar wrote: > >>> Add RTC DT entries in da850 dts file. > >>> > >>> Signed-off-by: Mrugesh Katepallewar <mrugesh...@ti.com> > >>> --- > >>> Applies on top of v3.8-rc4 of linus tree. > >>> > >>> Tested on da850-evm device. > >>> > >>> Test Procedure: > >>> date [YYYY.]MM.DD-hh:mm[:ss] > >>> hwclock -w > >>> reset board and check system time. > >>> > >>> :100644 100644 37dc5a3... b16efd4... M arch/arm/boot/dts/da850-evm.dts > >>> :100644 100644 640ab75... a8eb1b1... M arch/arm/boot/dts/da850.dtsi > >>> arch/arm/boot/dts/da850-evm.dts | 3 +++ > >>> arch/arm/boot/dts/da850.dtsi | 8 ++++++++ > >>> 2 files changed, 11 insertions(+) > >>> > >>> diff --git a/arch/arm/boot/dts/da850-evm.dts > >>> b/arch/arm/boot/dts/da850-evm.dts index 37dc5a3..b16efd4 100644 > >>> --- a/arch/arm/boot/dts/da850-evm.dts > >>> +++ b/arch/arm/boot/dts/da850-evm.dts > >>> @@ -24,5 +24,8 @@ > >>> serial2: serial@1d0d000 { > >>> status = "okay"; > >>> }; > >>> + rtc@1c23000 { > > I did not mention this last time, but this should be: > > rtc0: rtc@1c23000 { > > to be consistent with rest of the file.
Okay. I will send this in next version. > > >>> + status = "okay"; > >>> + }; > >>> }; > >>> }; > >>> diff --git a/arch/arm/boot/dts/da850.dtsi > >>> b/arch/arm/boot/dts/da850.dtsi index 640ab75..a8eb1b1 100644 > >>> --- a/arch/arm/boot/dts/da850.dtsi > >>> +++ b/arch/arm/boot/dts/da850.dtsi > >>> @@ -56,5 +56,13 @@ > >>> interrupt-parent = <&intc>; > >>> status = "disabled"; > >>> }; > >>> + rtc@1c23000 { > > Here too. > Okay. I will send this in next version. > >>> + compatible = "ti,da830-rtc"; > >>> + reg = <0x23000 0x1000>; > >>> + interrupts = <19 > >>> + 19>; > >> > >> Why two interrupts of the same number? If there is only one interrupt line > >> then only one should be specified, no? > > We are using common OMAP RTC driver for da850 and other ti SoC's > > (e.g.am33xx). I have seen in am33xx.dtsi rtc timer and alarm interrupts are > > different. So, two interrupt numbers are expected from RTC DT node. > > Okay. Looking at the OMAP-L138 TRM, I see that the IP on that SoC supports > both alarm and timer events and both arrive on the same interrupt number (as > opposed to am335x where they supposedly arrive on different interrupt lines). > What you have looks fine to me considering this. > > Also, the interrupt-parent setting needs to be removed. See the patch > Prabhakar just submitted. Okay. I will send this in next version. > > Thanks, > Sekhar > Regards, Mrugesh _______________________________________________ Davinci-linux-open-source mailing list Davinci-linux-open-source@linux.davincidsp.com http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source