On 1/28/2013 7:17 PM, Prabhakar Lad wrote:
> From: Lad, Prabhakar <prabhakar....@ti.com>
>
> Add eth0 device tree node information and pinmux for mii to da850 by
> providing interrupt details and local mac address of eth0.
>
> Signed-off-by: Lad, Prabhakar <prabhakar....@ti.com>
> Cc: linux-arm-ker...@lists.infradead.org
> Cc: linux-ker...@vger.kernel.org
> Cc: davinci-linux-open-source@linux.davincidsp.com
> Cc: net...@vger.kernel.org
> Cc: devicetree-disc...@lists.ozlabs.org
> Cc: Sekhar Nori <nsek...@ti.com>
> Cc: Heiko Schocher <h...@denx.de>
> ---
> arch/arm/boot/dts/da850-evm.dts | 5 +++++
> arch/arm/boot/dts/da850.dtsi | 35 +++++++++++++++++++++++++++++++++++
> 2 files changed, 40 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts
> index a319491..19aa2b3 100644
> --- a/arch/arm/boot/dts/da850-evm.dts
> +++ b/arch/arm/boot/dts/da850-evm.dts
> @@ -30,6 +30,11 @@
> mdio: davinci_mdio@1e24000 {
> status = "okay";
> };
> + eth0: emac@1e20000 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&mii_pins>;
> + };
> };
> nand_cs3@62000000 {
> status = "okay";
> diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
> index ba28f2d..76905f3 100644
> --- a/arch/arm/boot/dts/da850.dtsi
> +++ b/arch/arm/boot/dts/da850.dtsi
> @@ -56,6 +56,26 @@
> 0x30 0x01100000 0x0ff00000
> >;
> };
> + mii_pins: pinmux_mii_pins {
> + pinctrl-single,bits = <
> + /*
> + * MII_TXEN, MII_TXCLK, MII_COL
> + * MII_TXD_3, MII_TXD_2, MII_TXD_1
> + * MII_TXD_0
> + */
> + 0x8 0x88888880 0xfffffff0
> + /*
> + * MII_RXER, MII_CRS, MII_RXCLK
> + * MII_RXDV, MII_RXD_3, MII_RXD_2
> + * MII_RXD_1, MII_RXD_0
> + */
> + 0xc 0x88888888 0xffffffff
> + /* MDIO_CLK, MDIO_D */
You call this mii_pins, but include mdio pins in there as well. Can you
separate them out? Then some board which uses rmii can simply reuse the
entry.
> + 0x10 0x00222288 0x00ffffff
> + /* GPIO2_6 */
> + 0x18 0x00000080 0x000000f0
This is SoC specific pin list. Such board specific pins should not make
it here.
> + >;
> + };
> };
> serial0: serial@1c42000 {
> compatible = "ns16550a";
> @@ -88,6 +108,21 @@
> reg = <0x224000 0x1000>;
> bus_freq = <2200000>;
> };
> + eth0: emac@1e20000 {
> + compatible = "ti,davinci-dm6467-emac";
> + reg = <0x220000 0x4000>;
> + ti,davinci-ctrl-reg-offset = <0x3000>;
> + ti,davinci-ctrl-mod-reg-offset = <0x2000>;
> + ti,davinci-ctrl-ram-offset = <0>;
> + ti,davinci-ctrl-ram-size = <0x2000>;
> + local-mac-address = [ 00 00 00 00 00 00 ];
> + interrupts = <33
> + 34
> + 35
> + 36
> + >;
> + phy-handle = <&mdio>;
I doubt this is required. This property is to pass a handle to the phy,
not mdio bus.
Thanks,
Sekhar
_______________________________________________
Davinci-linux-open-source mailing list
Davinci-linux-open-source@linux.davincidsp.com
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
