Have you assembled you raid devices again (mdadm --assemble /dev/mdX /dev/sdX)?
That should still work with the disk that was used for your RAID-1, when that's done you can mount your disk, chroot into it and run grub-install /dev/sda (and grub-install /dev/sdb, so you won't have this problem in the future ;-)). On 2 March 2013 11:10, Francesco Pietra <chiendar...@gmail.com> wrote: > A further piece on information. With knoppix 7.0, the procedure for > examining mdadm arrives at > > cat /proc/partitions > sda > sdb > > RAID1 (md0 md1) is not seen. I assume that this is the way Knoppix > behaves in this situation. > > Thanks > francesco pietra > > > ---------- Forwarded message ---------- > From: Francesco Pietra <chiendar...@gmail.com> > Date: Sat, Mar 2, 2013 at 10:11 AM > Subject: Re: RAID1 all bootable > To: Lennart Sorensen <lsore...@csclub.uwaterloo.ca>, amd64 Debian > <debian-amd64@lists.debian.org>, debian-users > <debian-u...@lists.debian.org> > > > Is this recipe devised for installing grub on both sda and sda with an > undamaged RAID1? > > In my case, with the sda that contained grub loader replaced by a new > disk, the rescue mode (using the same CD installer for amd64 wheezy) > did not find any partition. Inverting the SATA cables, same result. > > In both cases (I mean position of SATA cables) I went to the shell in > the installer environment: > > #fisk /dev/sda (or sdb) > device contains neither a valid DOS partition table, nor Sun, etc > (expected for a raid) > > #dmesg |grep -i sd > sda (and sbb): unknown partition table (expected for a raid), however > md: raid0 > md: raid1 > were identified, along with rai4, 5, 6 etc (unfortunately "| less" > does not work to see the whole message). > > Am I using the Rescue Mode improperly? I was unable to dig into the HD > that contains md0 (booth loader, EXT2) and md1 ( LVM partitions home > tmp usr opt var swap EXT3) > > Thanks a lot for your kind advice > > francesco pietra > > > > On Fri, Mar 1, 2013 at 10:35 PM, Lennart Sorensen > <lsore...@csclub.uwaterloo.ca> wrote: > > On Fri, Mar 01, 2013 at 08:20:09PM +0100, Francesco Pietra wrote: > >> Hi: > >> With a raid1 amd64 wheezy, one of the two HDs got broken. > >> Unfortunately, I had added grub to sda only, which is just the one > >> broken. So that, when it is replaced with a fresh HD, the OS is not > >> found. Inverting the SATA cables of course does not help (Operative > >> System Not Found). In a previous similar circumstance, I was lucky > >> that the broken HD was the one without gru. > >> > >> Is any way to recover? perhaps through Knoppix? I know how to look > >> into undamaged RAID1 with Knoppix. > >> > >> Also, when making a fresh RAID1 from scratch, where to find a Debian > >> description of how to make both sda and sdb bootable? (which should > >> be included by default, in my opinion) > > > > You can boot the install disk in rescue mode, select the root partition > > to chroot into, then run grub-install from there. > > > > When grub asks where to install, you should configure it for both sda > > and sdb. I think 'dpkg-reconfigure grub-pc' is where that is selected. > > Might need it to use -plow to asks all levels of questions. Not sure. > > > > -- > > Len Sorensen > > > -- > To UNSUBSCRIBE, email to debian-amd64-requ...@lists.debian.org > with a subject of "unsubscribe". Trouble? Contact > listmas...@lists.debian.org > Archive: > http://lists.debian.org/caev0nmtmhadi2e_uk+wf+c0k9d1ygn3tv91jsr4g2ppp5_a...@mail.gmail.com > >
