On Wed, 24 Apr 2013 20:52:33 +0300 Timo Juhani Lindfors <[email protected]> wrote:
> Richard Bown <[email protected]> writes: > > whats the default firewall mechanism on a fresh install of wheezy on a > > pogoplugE02. > > There is no firewall. > > > I ran webmin and while the daemon was running port 10000 was open, on a > > reboot that was closed > > again. > > How did you determine this? > > By running nmap:- and at this point motion was active, and webmin was not active. This is with ufw running as well . [richard@localhost ~]$ sudo nmap -vv -p1-20000 -sS 192.168.101.13 Starting Nmap 6.25 ( http://nmap.org ) at 2013-04-24 19:07 BST Initiating ARP Ping Scan at 19:07 Scanning 192.168.101.13 [1 port] Completed ARP Ping Scan at 19:07, 0.01s elapsed (1 total hosts) Initiating Parallel DNS resolution of 1 host. at 19:07 Completed Parallel DNS resolution of 1 host. at 19:07, 0.02s elapsed Initiating SYN Stealth Scan at 19:07 Scanning 192.168.101.13 [20000 ports] Discovered open port 22/tcp on 192.168.101.13 Discovered open port 631/tcp on 192.168.101.13 Completed SYN Stealth Scan at 19:08, 41.76s elapsed (20000 total ports) Nmap scan report for 192.168.101.13 Host is up (0.0016s latency). Scanned at 2013-04-24 19:07:45 BST for 42s Not shown: 19995 filtered ports PORT STATE SERVICE 22/tcp open ssh 631/tcp open ipp 8080/tcp closed http-proxy 8081/tcp closed blackice-icecap 10000/tcp closed snet-sensor-mgmt MAC Address: 00:25:31:04:97:78 (Cloud Engines) Read data files from: /usr/bin/../share/nmap Nmap done: 1 IP address (1 host up) scanned in 41.89 seconds Raw packets sent: 40027 (1.761MB) | Rcvd: 1633 (186.864KB) root@Pogopig:/etc# ufw status verbose Status: active Logging: on (low) Default: deny (incoming), allow (outgoing) New profiles: skip To Action From -- ------ ---- 22/tcp ALLOW IN Anywhere 8080/tcp ALLOW IN Anywhere 8081/tcp ALLOW IN Anywhere 631/tcp ALLOW IN Anywhere 10000/tcp ALLOW IN Anywhere 22/tcp ALLOW IN Anywhere (v6) 8080/tcp ALLOW IN Anywhere (v6) 8081/tcp ALLOW IN Anywhere (v6) 631/tcp ALLOW IN Anywhere (v6) 10000/tcp ALLOW IN Anywhere (v6) And this is with ufw diabled so the port should be open Starting Nmap 6.25 ( http://nmap.org ) at 2013-04-24 19:14 BST Initiating ARP Ping Scan at 19:14 Scanning 192.168.101.13 [1 port] Completed ARP Ping Scan at 19:14, 0.01s elapsed (1 total hosts) Initiating Parallel DNS resolution of 1 host. at 19:14 Completed Parallel DNS resolution of 1 host. at 19:14, 0.02s elapsed Initiating SYN Stealth Scan at 19:14 Scanning 192.168.101.13 [20000 ports] Discovered open port 22/tcp on 192.168.101.13 Discovered open port 631/tcp on 192.168.101.13 Completed SYN Stealth Scan at 19:14, 3.88s elapsed (20000 total ports) Nmap scan report for 192.168.101.13 Host is up (0.0058s latency). Scanned at 2013-04-24 19:14:16 BST for 4s Not shown: 19998 closed ports PORT STATE SERVICE 22/tcp open ssh 631/tcp open ipp MAC Address: 00:25:31:04:97:78 (Cloud Engines) Read data files from: /usr/bin/../share/nmap Nmap done: 1 IP address (1 host up) scanned in 4.03 seconds Raw packets sent: 20013 (880.556KB) | Rcvd: 20001 (800.036KB) With no firewall enable ports especially where Motion is running and using ports 8080 & 8081 /tcp should be open. But they are not. Something else is holding those ports shut. -- -- Best wishes / 73 Richard Bown Email : [email protected] HTTP :http://www.g8jvm.info nil carborundum a illegitemis ################################################################################## Ham Call G8JVM . OS Fedora FC18 x86_64 on a Dell Inspiron N5030 laptop Maidenhead QRA: IO82SP38, LAT. 52 39.720' N LONG. 2 28.171 W ( degs+mins ) QRV VHF 6mtrs 200W, 4 mtrs 150W, 2mtrs 350W, 70cms 200W Microwave 23 cms 140W, 13 cms 100W, 6 cms 0W & 3cms 5W ################################################################################## Please do not use the e-mail address of [email protected] Mail hosted by 1and1, Domain screwed up by 1and1 and Freeparking -- To UNSUBSCRIBE, email to [email protected] with a subject of "unsubscribe". Trouble? Contact [email protected] Archive: http://lists.debian.org/[email protected]
