Hi, I opened a bugreport against the kernel:
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=826518 Does anybody else see, that his cubox-i is not booting with newer kernels anymore? Thanks Rainer On Saturday 04 June 2016 14:35:29 Rainer Dorsch wrote: > On Saturday 04 June 2016 13:27:04 Karsten Merker wrote: > > On Sat, Jun 04, 2016 at 01:02:16PM +0200, Rainer Dorsch wrote: > > > On Saturday 04 June 2016 12:43:00 Rainer Dorsch wrote: > > > > On Saturday 04 June 2016 11:46:28 K. Merker wrote: > > > > > On Thu, Jun 02, 2016 at 09:30:35PM +0200, Rainer Dorsch wrote: > > > > > > after the upgrade to kernel 4.5.0-0.bpo.2-armmp, my cubox-i does > > > > > > not > > > > > > boot anymore. [...] > > > > [...] > > > > > Should I open a bug report against the kernel? > > > > Yes, that would be helpful. Could you perhaps give kernel 4.6 > > from experimental a try first? Kernel 4.6 has solved a number of > > regressions that had shown up in 4.5, so it would be interesting > > whether the problem still occurs with 4.6. > > 4.6.0 from experimental has the same issue: > > U-Boot 2014.10+dfsg1-2 (Nov 02 2014 - 00:31:26) > > CPU: Freescale i.MX6D rev1.2 at 792 MHz > Reset cause: POR > Board: MX6-CuBox-i > DRAM: 1 GiB > MMC: FSL_SDHC: 0 > In: serial > Out: vga > Err: vga > Net: FEC [PRIME] > (Re)start USB... > USB0: Port not available. > USB1: USB EHCI 1.00 > scanning bus 1 for devices... 1 USB Device(s) found > scanning usb for storage devices... 0 Storage Device(s) found > scanning usb for ethernet devices... 0 Ethernet Device(s) found > Hit any key to stop autoboot: 0 > switch to partitions #0, OK > mmc0 is current device > ** File not found /boot.scr ** > ** File not found uEnv.txt ** > ** File not found /zImage ** > ** File not found /uImage ** > 938 bytes read in 89 ms (9.8 KiB/s) > Running bootscript from mmc ... > ## Executing script at 10800000 > 3620480 bytes read in 308 ms (11.2 MiB/s) > 34350 bytes read in 231 ms (144.5 KiB/s) > 15046745 bytes read in 13548 ms (1.1 MiB/s) > Booting Debian 4.6.0-trunk-armmp from mmc 0:2... > Kernel image @ 0x10800000 [ 0x000000 - 0x373e80 ] > ## Flattened Device Tree blob at 18000000 > Booting using the fdt blob at 0x18000000 > EHCI failed to shut down host controller. > Using Device Tree in place at 18000000, end 1800b62d > > Starting kernel ... > > [ 0.000000] Booting Linux on physical CPU 0x0 > [ 0.000000] Linux version 4.6.0-trunk-armmp (debian- > [email protected]) (gcc version 5.3.1 20160509 (Debian 5.3.1-19) ) #1 > SMP Debian 4.6-1~exp1 (20) > [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), > cr=10c5387d > [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing > instruction cache > [ 0.000000] Machine model: SolidRun Cubox-i Dual/Quad > [ 0.000000] efi: Getting EFI parameters from FDT: > [ 0.000000] efi: UEFI not found. > [ 0.000000] cma: Reserved 16 MiB at 0x4f000000 > [ 0.000000] Memory policy: Data cache writealloc > [ 0.000000] percpu: Embedded 13 pages/cpu @ef6c0000 s20876 r8192 d24180 > u53248 > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total > pages: 260416 > [ 0.000000] Kernel command line: console=ttymxc0,115200 > root=/dev/mmcblk0p2 rootfstype=ext4 ro rootwait console=ttymxc0,115200 > console=tty1 elevator=noop [ 0.000000] PID hash table entries: 4096 > (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: > 131072 (order: 7, 524288 bytes) > [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 > bytes) [ 0.000000] Memory: 993568K/1048576K available (7773K kernel > code, 932K rwdata, 2560K rodata, 1024K init, 390K bss, 38624K reserved, > 16384K cma- reserved,) > [ 0.000000] Virtual kernel memory layout: > [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) > [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) > [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) > [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) > [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) > [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) > [ 0.000000] .text : 0xc0008000 - 0xc0b175d8 (11326 kB) > [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) > [ 0.000000] .data : 0xc0d00000 - 0xc0de9274 ( 933 kB) > [ 0.000000] .bss : 0xc0deb000 - 0xc0e4c9c4 ( 391 kB) > [ 0.000000] Hierarchical RCU implementation. > [ 0.000000] Build-time adjustment of leaf fanout to 32. > [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. > [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 > [ 0.000000] NR_IRQS:16 nr_irqs:16 16 > [ 0.000000] L2C-310 erratum 769419 enabled > [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 > [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 > [ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines > [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled > [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB > [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76070001 > [ 0.000000] Switching to timer-based delay loop, resolution 333ns > [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps > every 715827882841ns > [ 0.000027] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: > 0xffffffff, max_idle_ns: 637086815595 ns > [ 0.002819] Console: colour dummy device 80x30 > [ 0.003690] console [tty1] enabled > [ 0.003734] Calibrating delay loop (skipped), value calculated using > timer frequency.. 6.00 BogoMIPS (lpj=12000) > [ 0.003787] pid_max: default: 32768 minimum: 301 > [ 0.004004] Security Framework initialized > [ 0.004034] Yama: disabled by default; enable with sysctl kernel.yama.* > [ 0.004083] AppArmor: AppArmor disabled by boot time parameter > [ 0.004168] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) > [ 0.004203] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 > bytes) > [ 0.005109] Disabling memory control group subsystem > [ 0.005237] CPU: Testing write buffer coherency: ok > [ 0.005292] ftrace: allocating 25599 entries in 76 pages > [ 0.051928] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 > [ 0.052078] Setting up static identity map for 0x10100000 - 0x10100098 > [ 0.056882] EFI services will not be available. > [ 0.058099] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 > [ 0.058208] Brought up 2 CPUs > [ 0.058258] SMP: Total of 2 processors activated (12.00 BogoMIPS). > [ 0.058281] CPU: All CPU(s) started in SVC mode. > [ 0.059266] devtmpfs: initialized > [ 0.069031] VFP support v0.3: implementor 41 architecture 3 part 30 > variant 9 rev 4 > [ 0.069775] clocksource: jiffies: mask: 0xffffffff max_cycles: > 0xffffffff, max_idle_ns: 7645041785100000 ns > [ 0.071056] pinctrl core: initialized pinctrl subsystem > [ 0.072709] NET: Registered protocol family 16 > [ 0.075361] DMA: preallocated 256 KiB pool for atomic coherent > allocations [ 0.077348] CPU identified as i.MX6Q, silicon rev 1.2 > [ 0.101546] No ATAGs? > [ 0.101591] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 > watchpoint registers. > [ 0.101644] hw-breakpoint: maximum watchpoint size is 4 bytes. > [ 0.103399] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver > [ 0.104043] Serial: AMBA PL011 UART driver > [ 0.105005] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 > [ 0.124092] mxs-dma 110000.dma-apbh: initialized > [ 0.129451] vgaarb: loaded > [ 0.130834] media: Linux media interface: v0.10 > [ 0.130925] Linux video capture interface: v2.00 > [ 0.131038] pps_core: LinuxPPS API ver. 1 registered > [ 0.131062] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo > Giometti <[email protected]> > [ 0.131120] PTP clock support registered > [ 0.132999] clocksource: Switched to clocksource mxc_timer1 > [ 0.183201] VFS: Disk quotas dquot_6.6.0 > [ 0.183331] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 > bytes) [ 0.198417] NET: Registered protocol family 2 > [ 0.199207] TCP established hash table entries: 8192 (order: 3, 32768 > bytes) > [ 0.199322] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) > [ 0.199460] TCP: Hash tables configured (established 8192 bind 8192) > [ 0.199577] UDP hash table entries: 512 (order: 2, 16384 bytes) > [ 0.199649] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) > [ 0.199933] NET: Registered protocol family 1 > [ 0.200488] Unpacking initramfs... > [ 1.298072] Freeing initrd memory: 14696K (c1800000 - c265a000) > [ 1.305062] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 > counters available > [ 1.307390] futex hash table entries: 512 (order: 3, 32768 bytes) > [ 1.307549] audit: initializing netlink subsys (disabled) > [ 1.307637] audit: type=2000 audit(1.280:1): initialized > [ 1.308448] Initialise system trusted keyring > [ 1.308846] workingset: timestamp_bits=12 max_order=18 bucket_order=6 > [ 1.309054] zbud: loaded > [ 1.787726] Key type asymmetric registered > [ 1.787770] Asymmetric key parser 'x509' registered > [ 1.787881] bounce: pool size: 64 pages > [ 1.787977] Block layer SCSI generic (bsg) driver version 0.4 loaded > (major 248) > [ 1.788151] io scheduler noop registered (default) > [ 1.788187] io scheduler deadline registered > [ 1.788239] io scheduler cfq registered > [ 1.795974] imx-sdma 20ec000.sdma: firmware: failed to load > imx/sdma/sdma- imx6q.bin (-2) > [ 1.796026] imx-sdma 20ec000.sdma: Direct firmware load for > imx/sdma/sdma- imx6q.bin failed with error -2 > [ 1.802084] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled > [ 1.804393] Serial: AMBA driver > [ 1.805321] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 25, > base_baud = 5000000) is a IMX > [ 2.463573] console [ttymxc0] enabled > [ 2.468242] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 292, > base_baud = 5000000) is a IMX > [ 2.480979] 2188000.ethernet supply phy not found, using dummy regulator > [ 2.493514] pps pps0: new PPS source ptp0 > [ 2.502940] at803x: module verification failed: signature and/or required > key missing - tainting kernel > [ 2.516949] libphy: fec_enet_mii_bus: probed > [ 2.521951] fec 2188000.ethernet eth0: registered PHC device 0 > [ 2.528779] mousedev: PS/2 mouse device common for all mice > [ 2.536861] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered > 20cc000.snvs:snvs-r as rtc0 > [ 2.548557] ledtrig-cpu: registered to indicate activity on CPUs > [ 2.557617] NET: Registered protocol family 10 > [ 2.563138] mip6: Mobile IPv6 > [ 2.566180] NET: Registered protocol family 17 > [ 2.570690] mpls_gso: MPLS GSO support > [ 2.575533] ThumbEE CPU extension supported. > [ 2.579913] Registering SWP/SWPB emulation handler > [ 2.585746] registered taskstats version 1 > [ 2.589976] Loading compiled-in X.509 certificates > [ 2.603616] alg: No test for pkcs1pad(rsa,sha256) (pkcs1pad(rsa- > generic,sha256)) > [ 2.613851] Loaded X.509 cert 'Debian Project: Ben Hutchings: > 008a018dca80932630' > [ 2.621515] zswap: loaded using pool lzo/zbud > [ 2.626529] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 > [ 2.633914] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 > [ 2.640442] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to > 1970-01-01 00:00:00 UTC (0) > [ 2.640505] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 > [ 2.667981] brcm_reg: disabling > [ 2.671191] usb_h1_vbus: disabling > [ 2.674631] usb_otg_vbus: disabling > [ 2.679771] Freeing unused kernel memory: 1024K (c0c00000 - c0d00000) > [ 2.734205] systemd-udevd[77]: starting version 215 > [ 2.742207] random: systemd-udevd urandom read with 1 bits of entropy > available > [ 2.877463] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 > [ 2.885185] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 > [ 2.912790] sdhci: Secure Digital Host Controller Interface driver > [ 2.919068] sdhci: Copyright(c) Pierre Ossman > [ 2.930797] sdhci-pltfm: SDHCI platform and OF driver helper > [ 2.940130] sdhci-esdhc-imx 2190000.usdhc: allocated mmc-pwrseq > [ 2.971447] SCSI subsystem initialized > [ 3.002582] ahci-imx 2200000.sata: fsl,transmit-level-mV value 1104, > using 00000044 > [ 3.010353] ahci-imx 2200000.sata: fsl,transmit-boost-mdB value 0, using > 00000000 > [ 3.017926] ahci-imx 2200000.sata: fsl,transmit-atten-16ths value 9, > using 00002000 > [ 3.025662] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, > using 05000000 > [ 3.039927] ahci-imx 2200000.sata: SSS flag set, parallel bus scan > disabled [ 3.046999] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 > ports 3 Gbps 0x1 impl platform mode > [ 3.055857] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only > pmp pio slum part ccc apst > [ 3.066715] scsi host0: ahci-imx > [ 3.070417] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port > 0x100 irq 295 > [ 3.213076] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using > ADMA > [ 3.227066] sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed > state, work on normal mode > [ 3.239343] sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO > [ 3.257301] mmc0: queuing unknown CIS tuple 0x80 (2 bytes) > [ 3.264558] mmc0: queuing unknown CIS tuple 0x80 (3 bytes) > [ 3.273877] mmc0: queuing unknown CIS tuple 0x80 (3 bytes) > [ 3.282498] mmc0: queuing unknown CIS tuple 0x80 (7 bytes) > [ 3.288197] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using > ADMA > [ 3.315837] mmc0: queuing unknown CIS tuple 0x80 (7 bytes) > [ 3.348860] mmc1: host does not support reading read-only switch, > assuming write-enable > [ 3.363182] mmc1: new high speed SDHC card at address 59b4 > [ 3.370276] mmcblk1: mmc1:59b4 USDU1 29.5 GiB > [ 3.376587] mmcblk1: p1 p2 > [ 3.388198] ata1: SATA link down (SStatus 0 SControl 300) > [ 3.393710] ahci-imx 2200000.sata: no device found, disabling link. > [ 3.400029] ahci-imx 2200000.sata: pass .hotplug=1 to enable hotplug > [ 3.402833] mmc0: new high speed SDIO card at address 0001 > [ 33.683919] usbcore: registered new interface driver usbfs > [ 33.689609] usbcore: registered new interface driver hub > [ 33.695106] usbcore: registered new device driver usb > [ 33.702900] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > [ 33.710293] ehci-pci: EHCI PCI platform driver > [ 33.721816] ehci-orion: EHCI orion driver > [ 33.744554] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver > [ 33.759893] hidraw: raw HID events driver (C) Jiri Kosina > [ 33.767821] usbcore: registered new interface driver usbhid > [ 33.773495] usbhid: USB HID core driver > > > For reference I add the output with the old kernel: > > U-Boot 2014.10+dfsg1-2 (Nov 02 2014 - 00:31:26) > > CPU: Freescale i.MX6D rev1.2 at 792 MHz > Reset cause: POR > Board: MX6-CuBox-i > DRAM: 1 GiB > MMC: FSL_SDHC: 0 > In: serial > Out: vga > Err: vga > Net: FEC [PRIME] > (Re)start USB... > USB0: Port not available. > USB1: USB EHCI 1.00 > scanning bus 1 for devices... 1 USB Device(s) found > scanning usb for storage devices... 0 Storage Device(s) found > scanning usb for ethernet devices... 0 Ethernet Device(s) found > Hit any key to stop autoboot: 0 > CuBox-i U-Boot > setenv kvers 4.5.0-0.bpo.1-armmp > CuBox-i U-Boot > run bootcmd > switch to partitions #0, OK > mmc0 is current device > ** File not found /boot.scr ** > ** File not found uEnv.txt ** > ** File not found /zImage ** > ** File not found /uImage ** > 938 bytes read in 89 ms (9.8 KiB/s) > Running bootscript from mmc ... > ## Executing script at 10800000 > 3571344 bytes read in 300 ms (11.4 MiB/s) > 34233 bytes read in 133 ms (251 KiB/s) > 15010048 bytes read in 882 ms (16.2 MiB/s) > Booting Debian 4.5.0-0.bpo.1-armmp from mmc 0:2... > Kernel image @ 0x10800000 [ 0x000000 - 0x367e90 ] > ## Flattened Device Tree blob at 18000000 > Booting using the fdt blob at 0x18000000 > EHCI failed to shut down host controller. > Using Device Tree in place at 18000000, end 1800b5b8 > > Starting kernel ... > > [ 0.000000] Booting Linux on physical CPU 0x0 > [ 0.000000] Linux version 4.5.0-0.bpo.1-armmp (debian- > [email protected]) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 SMP > Debian 4.5.1-1~bpo8+1 (2016-) > [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), > cr=10c5387d > [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing > instruction cache > [ 0.000000] Machine model: SolidRun Cubox-i Dual/Quad > [ 0.000000] Memory policy: Data cache writealloc > [ 0.000000] PERCPU: Embedded 12 pages/cpu @ef6c2000 s20032 r8192 d20928 > u49152 > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total > pages: 260416 > [ 0.000000] Kernel command line: console=ttymxc0,115200 > root=/dev/mmcblk0p2 rootfstype=ext4 ro rootwait console=ttymxc0,115200 > console=tty1 elevator=noop [ 0.000000] PID hash table entries: 4096 > (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: > 131072 (order: 7, 524288 bytes) > [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 > bytes) [ 0.000000] Memory: 1011524K/1048576K available (7288K kernel > code, 921K rwdata, 2528K rodata, 940K init, 394K bss, 37052K reserved, 0K > cma-reserved, 262) > [ 0.000000] Virtual kernel memory layout: > [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) > [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) > [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) > [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) > [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) > [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) > [ 0.000000] .text : 0xc0008000 - 0xc099e3bc (9817 kB) > [ 0.000000] .init : 0xc099f000 - 0xc0a8a000 ( 940 kB) > [ 0.000000] .data : 0xc0a8a000 - 0xc0b706fc ( 922 kB) > [ 0.000000] .bss : 0xc0b73000 - 0xc0bd5984 ( 395 kB) > [ 0.000000] Hierarchical RCU implementation. > [ 0.000000] Build-time adjustment of leaf fanout to 32. > [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. > [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 > [ 0.000000] NR_IRQS:16 nr_irqs:16 16 > [ 0.000000] L2C-310 erratum 769419 enabled > [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 > [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 > [ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines > [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled > [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB > [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76070001 > [ 0.000000] Switching to timer-based delay loop, resolution 333ns > [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps > every 715827882841ns > [ 0.000026] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: > 0xffffffff, max_idle_ns: 637086815595 ns > [ 0.002806] Console: colour dummy device 80x30 > [ 0.003599] console [tty1] enabled > [ 0.003641] Calibrating delay loop (skipped), value calculated using > timer frequency.. 6.00 BogoMIPS (lpj=12000) > [ 0.003692] pid_max: default: 32768 minimum: 301 > [ 0.003904] Security Framework initialized > [ 0.003936] Yama: disabled by default; enable with sysctl kernel.yama.* > [ 0.003983] AppArmor: AppArmor disabled by boot time parameter > [ 0.004067] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) > [ 0.004102] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 > bytes) > [ 0.004934] Disabling memory control group subsystem > [ 0.005064] CPU: Testing write buffer coherency: ok > [ 0.005118] ftrace: allocating 25233 entries in 74 pages > [ 0.050727] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 > [ 0.050891] Setting up static identity map for 0x10008280 - 0x10008318 > [ 0.056614] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 > [ 0.056712] Brought up 2 CPUs > [ 0.056765] SMP: Total of 2 processors activated (12.00 BogoMIPS). > [ 0.056788] CPU: All CPU(s) started in SVC mode. > [ 0.057669] devtmpfs: initialized > [ 0.067281] VFP support v0.3: implementor 41 architecture 3 part 30 > variant 9 rev 4 > [ 0.068029] clocksource: jiffies: mask: 0xffffffff max_cycles: > 0xffffffff, max_idle_ns: 7645041785100000 ns > [ 0.068313] pinctrl core: initialized pinctrl subsystem > [ 0.069755] NET: Registered protocol family 16 > [ 0.070687] DMA: preallocated 256 KiB pool for atomic coherent > allocations [ 0.072639] CPU identified as i.MX6Q, silicon rev 1.2 > [ 0.094673] No ATAGs? > [ 0.094715] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 > watchpoint registers. > [ 0.094767] hw-breakpoint: maximum watchpoint size is 4 bytes. > [ 0.096379] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver > [ 0.096996] Serial: AMBA PL011 UART driver > [ 0.097942] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 > [ 0.115893] mxs-dma 110000.dma-apbh: initialized > [ 0.121085] vgaarb: loaded > [ 0.122451] media: Linux media interface: v0.10 > [ 0.122531] Linux video capture interface: v2.00 > [ 0.122636] pps_core: LinuxPPS API ver. 1 registered > [ 0.122658] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo > Giometti <[email protected]> > [ 0.122710] PTP clock support registered > [ 0.124461] clocksource: Switched to clocksource mxc_timer1 > [ 0.172052] VFS: Disk quotas dquot_6.6.0 > [ 0.172176] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 > bytes) [ 0.186867] NET: Registered protocol family 2 > [ 0.187647] TCP established hash table entries: 8192 (order: 3, 32768 > bytes) > [ 0.187760] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) > [ 0.187898] TCP: Hash tables configured (established 8192 bind 8192) > [ 0.188014] UDP hash table entries: 512 (order: 2, 16384 bytes) > [ 0.188082] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) > [ 0.188365] NET: Registered protocol family 1 > [ 0.188994] Unpacking initramfs... > [ 1.271906] Freeing initrd memory: 14660K (c1800000 - c2651000) > [ 1.279187] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 > counters available > [ 1.281493] futex hash table entries: 512 (order: 3, 32768 bytes) > [ 1.281646] audit: initializing netlink subsys (disabled) > [ 1.281730] audit: type=2000 audit(1.260:1): initialized > [ 1.282567] Initialise system trusted keyring > [ 1.283117] zbud: loaded > [ 1.285970] Key type asymmetric registered > [ 1.286011] Asymmetric key parser 'x509' registered > [ 1.286117] bounce: pool size: 64 pages > [ 1.286214] Block layer SCSI generic (bsg) driver version 0.4 loaded > (major 249) > [ 1.286389] io scheduler noop registered (default) > [ 1.286428] io scheduler deadline registered > [ 1.286481] io scheduler cfq registered > [ 1.293925] imx-sdma 20ec000.sdma: firmware: failed to load > imx/sdma/sdma- imx6q.bin (-2) > [ 1.293975] imx-sdma 20ec000.sdma: Direct firmware load for > imx/sdma/sdma- imx6q.bin failed with error -2 > [ 1.299578] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled > [ 1.301901] Serial: AMBA driver > [ 1.302747] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 25, > base_baud = 5000000) is a IMX > [ 1.936888] console [ttymxc0] enabled > [ 1.941571] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 292, > base_baud = 5000000) is a IMX > [ 1.954293] 2188000.ethernet supply phy not found, using dummy regulator > [ 1.968973] pps pps0: new PPS source ptp0 > [ 1.978415] at803x: module verification failed: signature and/or required > key missing - tainting kernel > [ 1.992490] libphy: fec_enet_mii_bus: probed > [ 1.997424] fec 2188000.ethernet eth0: registered PHC device 0 > [ 2.004239] mousedev: PS/2 mouse device common for all mice > [ 2.012214] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered > 20cc000.snvs:snvs-r as rtc0 > [ 2.023905] ledtrig-cpu: registered to indicate activity on CPUs > [ 2.032415] NET: Registered protocol family 10 > [ 2.037913] mip6: Mobile IPv6 > [ 2.040983] NET: Registered protocol family 17 > [ 2.045492] mpls_gso: MPLS GSO support > [ 2.050312] ThumbEE CPU extension supported. > [ 2.054689] Registering SWP/SWPB emulation handler > [ 2.060530] registered taskstats version 1 > [ 2.064722] Loading compiled-in X.509 certificates > [ 2.072275] Loaded X.509 cert 'Debian Project: Ben Hutchings: > 008a018dca80932630' > [ 2.079931] zswap: loaded using pool lzo/zbud > [ 2.085005] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 > [ 2.092225] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 > [ 2.098748] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to > 1970-01-01 00:00:00 UTC (0) > [ 2.098800] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 > [ 2.126638] brcm_reg: disabling > [ 2.129841] usb_h1_vbus: disabling > [ 2.133275] usb_otg_vbus: disabling > [ 2.138145] Freeing unused kernel memory: 940K (c099f000 - c0a8a000) > [ 2.192000] systemd-udevd[67]: starting version 215 > [ 2.200012] random: systemd-udevd urandom read with 1 bits of entropy > available > [ 2.305373] SCSI subsystem initialized > [ 2.345986] imx-gpc 20dc000.gpc: failed to get pu regulator: -517 > [ 2.363482] ahci-imx 2200000.sata: fsl,transmit-level-mV value 1104, > using 00000044 > [ 2.371275] ahci-imx 2200000.sata: fsl,transmit-boost-mdB value 0, using > 00000000 > [ 2.374346] sdhci: Secure Digital Host Controller Interface driver > [ 2.374348] sdhci: Copyright(c) Pierre Ossman > [ 2.375232] sdhci-pltfm: SDHCI platform and OF driver helper > [ 2.377344] /soc/aips-bus@02100000/usdhc@02190000: voltage-ranges > unspecified > [ 2.377353] sdhci-esdhc-imx 2190000.usdhc: could not get ultra high speed > state, work on normal mode > [ 2.377673] sdhci-esdhc-imx 2190000.usdhc: allocated mmc-pwrseq > [ 2.417576] ahci-imx 2200000.sata: fsl,transmit-atten-16ths value 9, > using 00002000 > [ 2.425304] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, > using 05000000 > [ 2.440142] ahci-imx 2200000.sata: SSS flag set, parallel bus scan > disabled [ 2.447226] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 > ports 3 Gbps 0x1 impl platform mode > [ 2.456097] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only > pmp pio slum part ccc apst > [ 2.467300] scsi host0: ahci-imx > [ 2.471017] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port > 0x100 irq 295 > [ 2.632549] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using > ADMA > [ 2.640433] /soc/aips-bus@02100000/usdhc@02194000: voltage-ranges > unspecified > [ 2.647653] sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed > state, work on normal mode > [ 2.658918] sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO > [ 2.680193] mmc0: queuing unknown CIS tuple 0x80 (2 bytes) > [ 2.687447] mmc0: queuing unknown CIS tuple 0x80 (3 bytes) > [ 2.696771] mmc0: queuing unknown CIS tuple 0x80 (3 bytes) > [ 2.705404] mmc0: queuing unknown CIS tuple 0x80 (7 bytes) > [ 2.711126] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using > ADMA > [ 2.734972] mmc0: queuing unknown CIS tuple 0x80 (7 bytes) > [ 2.772217] mmc1: host does not support reading read-only switch, > assuming write-enable > [ 2.786480] mmc1: new high speed SDHC card at address 59b4 > [ 2.788623] ata1: SATA link down (SStatus 0 SControl 300) > [ 2.788668] ahci-imx 2200000.sata: no device found, disabling link. > [ 2.788674] ahci-imx 2200000.sata: pass .hotplug=1 to enable hotplug > [ 2.813851] mmcblk0: mmc1:59b4 USDU1 29.5 GiB > [ 2.819802] mmcblk0: p1 p2 > [ 2.843994] mmc0: new high speed SDIO card at address 0001 > [ 3.295906] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data > mode. Opts: (null) > [ 3.739803] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT > +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR) > [ 3.753463] systemd[1]: Detected architecture 'arm'. > [ 3.849841] systemd[1]: Inserted module 'autofs4' > [ 3.855935] systemd[1]: Set hostname to <home>. > [ 4.312773] systemd[1]: Cannot add dependency job for unit display- > manager.service, ignoring: Unit display-manager.service failed to load: No > such file o. > [ 4.327927] systemd[1]: Found ordering cycle on basic.target/start > [ 4.334183] systemd[1]: Found dependency on sysinit.target/start > [ 4.340252] systemd[1]: Found dependency on > systemd-journald.service/start [ 4.347187] systemd[1]: Found dependency > on systemd-journald-dev- log.socket/start > [ 4.354725] systemd[1]: Found dependency on rtcemu.service/start > [ 4.360833] systemd[1]: Found dependency on basic.target/start > [ 4.366745] systemd[1]: Breaking ordering cycle by deleting job systemd- > journald.service/start > [ 4.375432] systemd[1]: Job systemd-journald.service/start deleted to > break ordering cycle starting with basic.target/start > [ 4.387106] systemd[1]: Found ordering cycle on basic.target/start > [ 4.393367] systemd[1]: Found dependency on sockets.target/start > [ 4.399447] systemd[1]: Found dependency on systemd-journald-dev- > log.socket/start > [ 4.406994] systemd[1]: Found dependency on rtcemu.service/start > [ 4.413054] systemd[1]: Found dependency on basic.target/start > [ 4.418942] systemd[1]: Breaking ordering cycle by deleting job > sockets.target/start > [ 4.426748] systemd[1]: Job sockets.target/start deleted to break > ordering cycle starting with basic.target/start > [ 4.439930] systemd[1]: Starting Forward Password Requests to Wall > Directory Watch. > [ 4.448001] systemd[1]: Started Forward Password Requests to Wall > Directory Watch. > [ 4.455711] systemd[1]: Expecting device dev-ttymxc0.device... > [ 4.461828] systemd[1]: Starting Remote File Systems (Pre). > [ 4.467696] systemd[1]: Reached target Remote File Systems (Pre). > [ 4.473931] systemd[1]: Starting Encrypted Volumes. > [ 4.479094] systemd[1]: Reached target Encrypted Volumes. > [ 4.484684] systemd[1]: Starting Arbitrary Executable File Formats File > System Automount Point. > [ 4.494301] systemd[1]: Set up automount Arbitrary Executable File > Formats File System Automount Point. > [ 4.503867] systemd[1]: Starting Dispatch Password Requests to Console > Directory Watch. > [ 4.512159] systemd[1]: Started Dispatch Password Requests to Console > Directory Watch. > [ 4.520201] systemd[1]: Starting Paths. > [ 4.524302] systemd[1]: Reached target Paths. > [ 4.528780] systemd[1]: Expecting device dev-disk- > by\x2duuid-07b3f3c9\x2ddeef\x2d4b5c\x2d8dc8\x2d7ffcb7b81a11.device... > [ 4.539846] systemd[1]: Starting Root Slice. > [ 4.544488] systemd[1]: Created slice Root Slice. > [ 4.549306] systemd[1]: Starting User and Session Slice. > [ 4.555055] systemd[1]: Created slice User and Session Slice. > [ 4.560926] systemd[1]: Starting Delayed Shutdown Socket. > [ 4.566699] systemd[1]: Listening on Delayed Shutdown Socket. > [ 4.572569] systemd[1]: Starting /dev/initctl Compatibility Named Pipe. > [ 4.579600] systemd[1]: Listening on /dev/initctl Compatibility Named > Pipe. [ 4.586706] systemd[1]: Starting udev Control Socket. > [ 4.592118] systemd[1]: Listening on udev Control Socket. > [ 4.597657] systemd[1]: Starting udev Kernel Socket. > [ 4.602953] systemd[1]: Listening on udev Kernel Socket. > [ 4.608405] systemd[1]: Starting Journal Socket. > [ 4.613493] systemd[1]: Listening on Journal Socket. > [ 4.618628] systemd[1]: Starting System Slice. > [ 4.623513] systemd[1]: Created slice System Slice. > [ 4.628592] systemd[1]: Started File System Check on Root Device. > [ 4.634798] systemd[1]: Starting system-getty.slice. > [ 4.640261] systemd[1]: Created slice system-getty.slice. > [ 4.645784] systemd[1]: Starting system-serial\x2dgetty.slice. > [ 4.652098] systemd[1]: Created slice system-serial\x2dgetty.slice. > [ 4.658557] systemd[1]: Starting Increase datagram queue length... > [ 4.677267] systemd[1]: Mounted Huge Pages File System. > [ 4.704076] systemd[1]: Started Set Up Additional Binary Formats. > [ 4.714341] systemd[1]: Starting Load Kernel Modules... > [ 4.733297] systemd[1]: Starting udev Coldplug all Devices... > [ 4.750503] systemd[1]: Starting Create list of required static device > nodes for the current kernel... > [ 4.765346] systemd[1]: Mounting POSIX Message Queue File System... > [ 4.777646] systemd[1]: Mounting Debug File System... > [ 4.781081] fuse init (API version 7.24) > [ 4.791114] systemd[1]: Starting Slices. > [ 4.796095] systemd[1]: Reached target Slices. > [ 4.804353] systemd[1]: Started Increase datagram queue length. > [ 4.813002] systemd[1]: Found ordering cycle on systemd- > journald.service/start > [ 4.822336] systemd[1]: Found dependency on systemd-journald-dev- > log.socket/start > [ 4.830583] systemd[1]: Found dependency on rtcemu.service/start > [ 4.840550] systemd[1]: Found dependency on basic.target/start > [ 4.851822] systemd[1]: Found dependency on sysinit.target/start > [ 4.861203] systemd[1]: Found dependency on > systemd-journald.service/start [ 4.868351] systemd[1]: Breaking ordering > cycle by deleting job systemd- journald-dev-log.socket/start > [ 4.877718] systemd[1]: Job systemd-journald-dev-log.socket/start deleted > to break ordering cycle starting with systemd-journald.service/start [ > 4.891092] systemd[1]: Found ordering cycle on systemd- > journald.service/start > [ 4.898445] systemd[1]: Found dependency on systemd-journald-dev- > log.socket/start > [ 4.906035] systemd[1]: Found dependency on rtcemu.service/start > [ 4.912134] systemd[1]: Found dependency on basic.target/start > [ 4.918058] systemd[1]: Found dependency on sysinit.target/start > [ 4.924130] systemd[1]: Found dependency on > systemd-journald.service/start [ 4.931063] systemd[1]: Unable to break > cycle > [ 4.935491] systemd[1]: Requested transaction contains an unfixable > cyclic ordering dependency: Transaction order is cyclic. See system logs > for details. [ 4.949309] systemd[1]: systemd-journald.socket failed to > queue service startup job (Maybe the service file is missing or not a > non-template unit?): Tran. > [ 4.967892] systemd[1]: Unit systemd-journald.socket entered failed > state. [ 4.975984] systemd[1]: Mounted Debug File System. > [ 4.981197] systemd[1]: Mounted POSIX Message Queue File System. > [ 4.988631] systemd[1]: Started Load Kernel Modules. > [ 5.010875] systemd[1]: Started Create list of required static device > nodes for the current kernel. > [ 5.061136] systemd[1]: Started udev Coldplug all Devices. > [ 5.128324] systemd[1]: Starting Create Static Device Nodes in /dev... > [ 5.149584] systemd[1]: Mounted Configuration File System. > [ 5.155371] systemd[1]: Starting Apply Kernel Variables... > [ 5.164636] systemd[1]: Mounting FUSE Control File System... > [ 5.174431] systemd[1]: Starting Syslog Socket. > [ 5.179691] systemd[1]: Listening on Syslog Socket. > [ 5.197817] systemd[1]: Mounted FUSE Control File System. > [ 5.205097] systemd[1]: Started Apply Kernel Variables. > [ 5.278240] systemd[1]: Started Create Static Device Nodes in /dev. > [ 5.291699] systemd[1]: Starting udev Kernel Device Manager... > [ 5.324905] systemd-udevd[156]: starting version 215 > [ 5.330269] systemd[1]: Started udev Kernel Device Manager. > [ 5.336294] systemd[1]: Starting Copy rules generated while the root was > ro... > [ 5.357328] systemd[1]: Starting LSB: Set preliminary keymap... > [ 5.375775] systemd[1]: Started Copy rules generated while the root was > ro. [ 5.387172] systemd[1]: Started LSB: Set preliminary keymap. > [ 5.400993] systemd[1]: Starting Remount Root and Kernel File Systems... > [ 5.603164] EXT4-fs (mmcblk0p2): re-mounted. Opts: > discard,data=ordered,errors=remount-ro > [ 5.614370] systemd[1]: Started Remount Root and Kernel File Systems. > [ 5.629386] systemd[1]: Started Various fixups to make systemd work > better on Debian. > [ 5.637681] systemd[1]: Starting Load/Save Random Seed... > [ 5.661386] systemd[1]: Starting Local File Systems (Pre). > [ 5.667304] systemd[1]: Reached target Local File Systems (Pre). > [ 5.673554] systemd[1]: Mounting /tmp... > [ 5.716974] systemd[1]: Started Load/Save Random Seed. > [ 5.734394] systemd[1]: Mounted /tmp. > [ 5.835999] systemd[1]: Starting Local File Systems. > [ 5.842767] systemd[1]: Reached target Local File Systems. > [ 5.849879] systemd[1]: Starting Create Volatile Files and Directories... > [ 5.885415] systemd[1]: Starting Remote File Systems. > [ 5.893126] systemd[1]: Reached target Remote File Systems. > [ 5.898985] systemd[1]: Starting LSB: Set console font and keymap... > [ 5.934816] systemd[1]: Starting LSB: Raise network interfaces.... > [ 5.997960] Registered IR keymap rc-empty > [ 6.004722] input: gpio_ir_recv as > /devices/soc0/ir-receiver/rc/rc0/input1 [ 6.018326] systemd[1]: Started > Create Volatile Files and Directories. [ 6.035455] rc rc0: gpio_ir_recv > as /devices/soc0/ir-receiver/rc/rc0 [ 6.054005] systemd[1]: Started LSB: > Set console font and keymap. [ 6.103240] imx2-wdt 20bc000.wdog: timeout > 60 sec (nowayout=0) > [ 6.103447] [drm] Initialized drm 1.1.0 20060810 > [ 6.135012] etnaviv gpu-subsystem: bound 134000.gpu (ops gpu_ops > [etnaviv]) [ 6.139290] lirc_dev: IR Remote Control driver registered, > major 244 [ 6.151225] rc rc0: lirc_dev: driver ir-lirc-codec > (gpio-rc-recv) registered at minor = 0 > [ 6.159554] IR LIRC bridge handler initialized > [ 6.225980] etnaviv gpu-subsystem: bound 130000.gpu (ops gpu_ops > [etnaviv]) [ 6.233422] systemd[1]: Found device /dev/ttymxc0. > [ 6.273175] etnaviv gpu-subsystem: bound 2204000.gpu (ops gpu_ops > [etnaviv]) > [ 6.300511] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 > [ 6.313150] i2c i2c-1: IMX I2C adapter registered > [ 6.324883] i2c i2c-1: can't use DMA, using PIO instead. > [ 6.329618] usbcore: registered new interface driver usbfs > [ 6.329688] usbcore: registered new interface driver hub > [ 6.334666] systemd[1]: Starting Update UTMP about System > Boot/Shutdown... [ 6.334822] usbcore: registered new device driver usb > [ 6.377232] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 > [ 6.390688] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > [ 6.416070] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 > [ 6.422242] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 > [ 6.428557] etnaviv-gpu 2204000.gpu: hw init failed: -6 > [ 6.474874] rtc-pcf8523 2-0068: rtc core: registered rtc-pcf8523 as rtc1 > [ 6.497711] i2c i2c-2: IMX I2C adapter registered > [ 6.514315] i2c i2c-2: can't use DMA, using PIO instead. > [ 6.522770] systemd[1]: Started Update UTMP about System Boot/Shutdown. > [ 6.569734] ci_hdrc ci_hdrc.0: EHCI Host Controller > [ 6.581655] imx-ipuv3 2400000.ipu: IPUv3H probed > [ 6.583826] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus > number 1 > [ 6.593412] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 > [ 6.593719] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 > [ 6.593727] usb usb1: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 6.593733] usb usb1: Product: EHCI Host Controller > [ 6.593738] usb usb1: Manufacturer: Linux 4.5.0-0.bpo.1-armmp ehci_hcd > [ 6.593743] usb usb1: SerialNumber: ci_hdrc.0 > [ 6.594520] hub 1-0:1.0: USB hub found > [ 6.594561] hub 1-0:1.0: 1 port detected > [ 6.610929] ci_hdrc ci_hdrc.1: EHCI Host Controller > [ 6.610965] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus > number 2 > [ 6.620532] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 > [ 6.620832] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 > [ 6.620840] usb usb2: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 6.620846] usb usb2: Product: EHCI Host Controller > [ 6.620851] usb usb2: Manufacturer: Linux 4.5.0-0.bpo.1-armmp ehci_hcd > [ 6.620856] usb usb2: SerialNumber: ci_hdrc.1 > [ 6.621632] hub 2-0:1.0: USB hub found > [ 6.621681] hub 2-0:1.0: 1 port detected > [ 6.678802] imx-spdif sound-spdif: snd-soc-dummy-dai <-> 2004000.spdif > mapping ok > [ 6.706152] imx-ipuv3 2800000.ipu: IPUv3H probed > [ 6.715981] systemd[1]: Found device /dev/disk/by-uuid/07b3f3c9- > deef-4b5c-8dc8-7ffcb7b81a11. > [ 6.780926] usbcore: registered new interface driver brcmfmac > [ 6.794436] systemd[1]: Activating swap /dev/disk/by-uuid/07b3f3c9- > deef-4b5c-8dc8-7ffcb7b81a11... > [ 6.847179] brcmfmac_sdio mmc0:0001:1: firmware: direct-loading firmware > brcm/brcmfmac4330-sdio.bin > [ 6.876525] brcmfmac_sdio mmc0:0001:1: firmware: failed to load > brcm/brcmfmac4330-sdio.txt (-2) > [ 6.885371] brcmfmac_sdio mmc0:0001:1: Direct firmware load for > brcm/brcmfmac4330-sdio.txt failed with error -2 > [ 6.911276] systemd[1]: Starting Sound Card. > [ 6.916876] systemd[1]: Reached target Sound Card. > [ 6.920538] usb 1-1: new full-speed USB device number 2 using ci_hdrc > [ 6.929236] systemd[1]: Starting system-ifup.slice. > [ 6.935161] Adding 4194300k swap on /dev/mmcblk0p1. Priority:-1 > extents:1 across:4194300k SSFS > [ 6.944342] systemd[1]: Created slice system-ifup.slice. > [ 6.956622] systemd[1]: Activated swap /dev/disk/by-uuid/07b3f3c9- > deef-4b5c-8dc8-7ffcb7b81a11. > [ 6.979633] systemd[1]: Starting Swap. > [ 6.983851] systemd[1]: Reached target Swap. > [ 7.056093] usb 1-1: New USB device found, idVendor=04fa, idProduct=2490 > [ 7.062873] usb 1-1: New USB device strings: Mfr=0, Product=0, > SerialNumber=0 > [ 7.477478] Atheros 8035 ethernet 2188000.ethernet:00: attached PHY > driver [Atheros 8035 ethernet] (mii_bus:phy_addr=2188000.ethernet:00, > irq=-1) [ 7.490823] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready > [ 7.511530] systemd[1]: Started LSB: Raise network interfaces.. > [ 7.518570] systemd[1]: Starting ifup for eth0... > [ 7.537642] systemd[1]: Started ifup for eth0. > [ 7.543951] systemd[1]: Starting Network. > [ 7.548528] systemd[1]: Reached target Network. > [ 7.553411] systemd[1]: Starting Network is Online. > [ 7.558770] systemd[1]: Reached target Network is Online. > [ 7.564377] systemd[1]: Starting LSB: RPC portmapper replacement... > [ 7.825287] systemd[1]: Started LSB: RPC portmapper replacement. > [ 7.832370] systemd[1]: Starting RPC Port Mapper. > [ 7.837437] systemd[1]: Reached target RPC Port Mapper. > [ 7.842782] systemd[1]: Starting LSB: NFS support files common to client > and server... > [ 7.928592] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): > clkctl 0x50 > [ 8.140870] RPC: Registered named UNIX socket transport module. > [ 8.146870] RPC: Registered udp transport module. > [ 8.151628] RPC: Registered tcp transport module. > [ 8.156364] RPC: Registered tcp NFSv4.1 backchannel transport module. > [ 8.192869] FS-Cache: Loaded > [ 8.243229] FS-Cache: Netfs 'nfs' registered for caching > [ 8.308238] Installing knfsd (copyright (C) 1996 [email protected]). > [ 8.401693] systemd[1]: Started LSB: NFS support files common to client > and server. > [ 8.410250] systemd[1]: Starting System Initialization. > [ 8.415793] systemd[1]: Reached target System Initialization. > [ 8.421676] systemd[1]: Starting D-Bus System Message Bus Socket. > [ 8.428202] systemd[1]: Listening on D-Bus System Message Bus Socket. > [ 8.434783] systemd[1]: Starting Daily Cleanup of Temporary Directories. > [ 8.441658] systemd[1]: Started Daily Cleanup of Temporary Directories. > [ 8.448425] systemd[1]: Starting Timers. > [ 8.452650] systemd[1]: Reached target Timers. > [ 8.457230] systemd[1]: Starting Basic System. > [ 8.461954] systemd[1]: Reached target Basic System. > [ 8.475609] systemd[1]: Starting OpenBSD Secure Shell server... > [ 8.497672] systemd[1]: Started OpenBSD Secure Shell server. > [ 8.504095] systemd[1]: Starting Regular background program processing > daemon... > [ 8.517751] systemd[1]: Started Regular background program processing > daemon. > [ 8.525805] systemd[1]: Starting Initialize hardware monitoring > sensors... [ 8.537287] systemd[1]: Starting Deferred execution > scheduler... [ 8.548834] systemd[1]: Started Deferred execution > scheduler. > [ 8.555486] systemd[1]: Starting Restore /etc/resolv.conf if the system > crashed before the ppp link was shut down.... > [ 8.570847] systemd[1]: Starting Run anacron jobs... > [ 8.581435] systemd[1]: Started Run anacron jobs. > [ 8.586951] systemd[1]: Starting /etc/rc.local Compatibility... > [ 8.597017] systemd[1]: Starting Login Service... > [ 8.606655] systemd[1]: Started getty on tty2-tty6 if dbus and logind are > not available. > [ 8.615289] systemd[1]: Starting LSB: start Samba daemons for the AD > DC... [ 8.635518] systemd[1]: Starting LSB: X display manager for KDE... > [ 8.646505] systemd[1]: Starting LSB: apt-cacher package caching proxy > daemon... > [ 8.667786] systemd[1]: Starting LSB: start Samba NetBIOS nameserver > (nmbd)... > [ 8.685413] systemd[1]: Starting LSB: keep memory of all UPnP devices > that announced themselves... > [ 8.710832] systemd[1]: Starting LSB: Increased Performance In Linux With > zRam (Virtual Swap Compressed in RAM)... > [ 8.725724] systemd[1]: Starting LSB: emulates the RTC by setting the > clock to the /var/log/syslog write time as early as possible... > [ 8.746931] systemd[1]: Starting D-Bus System Message Bus... > [ 8.778534] systemd[1]: Started D-Bus System Message Bus. > [ 8.936675] zram: Added device: zram0 > [ 8.942715] zram: Added device: zram1 > [ 8.956573] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): > clkctl 0x50 > [ 8.987975] zram0: detected capacity change from 0 to 525889536 > [ 8.995671] zram1: detected capacity change from 0 to 525889536 > [ 9.080556] Adding 513560k swap on /dev/zram0. Priority:100 extents:1 > across:513560k SSFS > [ 9.102474] Adding 513560k swap on /dev/zram1. Priority:100 extents:1 > across:513560k SSFS > [ 9.194254] systemd[1]: Starting System Logging Service... > [ 9.221463] systemd[1]: Starting Permit User Sessions... > [ 9.256608] systemd[1]: Started Restore /etc/resolv.conf if the system > crashed before the ppp link was shut down.. > [ 9.283589] systemd[1]: Started LSB: start Samba daemons for the AD DC. > [ 9.292391] systemd[1]: Started LSB: X display manager for KDE. > [ 9.300175] systemd[1]: Started LSB: start Samba NetBIOS nameserver > (nmbd). [ 9.309145] systemd[1]: Started LSB: keep memory of all UPnP > devices that announced themselves. > [ 9.319960] systemd[1]: Started LSB: Increased Performance In Linux With > zRam (Virtual Swap Compressed in RAM). > [ 9.332645] systemd[1]: Started LSB: emulates the RTC by setting the > clock to the /var/log/syslog write time as early as possible. > [ 9.346478] systemd[1]: Started Permit User Sessions. > [ 9.353255] systemd[1]: Started Initialize hardware monitoring sensors. > [ 9.363316] systemd[1]: Started System Logging Service. > [ 9.369193] systemd[1]: Time has been changed > [ 9.523728] systemd[1]: Starting Journal Socket (/dev/log). > [ 9.530496] systemd-logind[310]: New seat seat0. > [ 9.535523] systemd[1]: Listening on Journal Socket (/dev/log). > [ 9.547881] systemd[1]: Starting LSB: Apache2 web server... > [ 9.573220] systemd[1]: Starting LSB: Starts The Onion Router daemon > processes... > [ 9.584632] systemd[1]: Starting LSB: Start NTP daemon... > [ 9.599503] systemd[1]: Starting LSB: network connection manager... > [ 9.619870] systemd[1]: Starting LSB: Start the GNUstep distributed > object mapper... > [ 9.640153] systemd[1]: Starting LSB: Start and stop the mysql database > server daemon... > [ 9.679313] systemd[1]: Starting LSB: daemon to balance interrupts for > SMP systems... > [ 9.704125] systemd[1]: Starting LSB: 1-wire TCP server... > [ 9.757257] systemd[1]: Starting LSB: start Samba SMB/CIFS daemon > (smbd)... [ 9.875598] systemd[1]: Started LSB: network connection > manager. [ 9.898121] systemd[1]: Started LSB: Start the GNUstep > distributed object mapper. > [ 9.930256] systemd[1]: Started LSB: start Samba SMB/CIFS daemon (smbd). > [ 9.961973] systemd[1]: Started LSB: Start NTP daemon. > [ 9.984443] systemd[1]: Started LSB: daemon to balance interrupts for SMP > systems. > [ 10.020608] systemd[1]: Started Login Service. > [ 10.106476] systemd[1]: Starting Journal Socket. > [ 10.112358] systemd[1]: Listening on Journal Socket. > [ 10.118659] systemd[1]: Starting Journal Service... > [ 10.138453] systemd[1]: Started Journal Service. > [ 11.476933] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow > control rx/tx > [ 11.484699] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > [ 11.992107] random: nonblocking pool is initialized > [ 14.336848] systemd-logind[310]: New session c1 of user rd. > [ 15.837136] usb 1-1: usbfs: process 827 (owfs) did not claim interface 0 > before use > [ 15.846193] usb 1-1: usbfs: process 827 (owfs) did not claim interface 0 > before use > [ 15.866108] usb 1-1: usbfs: process 827 (owfs) did not claim interface 0 > before use > [ 15.882719] usb 1-1: usbfs: process 827 (owfs) did not claim interface 0 > before use > > Debian GNU/Linux 8 home ttymxc0 > > home login: > > > > Looking at the differences, the new kernels seem to fail to mount the EXT4 > root filesystem: > > [ 3.295906] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data > mode. Opts: (null) > > Kind regards > Rainer -- Rainer Dorsch http://bokomoko.de/
