Package: installation-reports Debian-installer-version: 20050112 from http://cdimage.debian.org/pub/cdimage-testing/daily/i386/
uname -a: Linux powerstation 2.4.27-1-386 #1 Wed Dec 1 19:43:08 JST 2004 i686 GNU/Linux Date: 13.01.2005 12:30 Method: network installation from ftp.de.debian.org, booted from sarge-i386-netinst.iso, no proxy used, installation mode default (linux) Machine: selfmade machine Processor: AMD Athlon 700 Mhz Memory: 386716 kB Root Device: IDE Maxtor 4K080H4, 80GB Root Size/partition table: hda1 ext3 mount on / hda2 swap Output of lspci and lspci -n: 0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03) 0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] 0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40) 0000:00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) 0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 16) 0000:00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40) 0000:00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 50) 0000:00:0a.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 74) 0000:00:0c.0 Ethernet controller: VIA Technologies, Inc. VT6105 [Rhine-III] (rev 86) 0000:00:0d.0 VGA compatible controller: S3 Inc. 86c764/765 [Trio32/64/64V+] (rev 44) 0000:00:00.0 0600: 1106:0305 (rev 03) 0000:00:01.0 0604: 1106:8305 0000:00:07.0 0601: 1106:0686 (rev 40) 0000:00:07.1 0101: 1106:0571 (rev 06) 0000:00:07.2 0c03: 1106:3038 (rev 16) 0000:00:07.4 0680: 1106:3057 (rev 40) 0000:00:07.5 0401: 1106:3058 (rev 50) 0000:00:0a.0 0200: 10b7:9200 (rev 74) 0000:00:0c.0 0200: 1106:3106 (rev 86) 0000:00:0d.0 0300: 5333:8811 (rev 44) Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot worked: [ O] Configure network HW: [ O] Config network: [O ] Detect CD: [ O] Load installer modules: [ O] (no errors seen during installation proccess) Detect hard drives: [O ] Partition hard drives: [O ] Create file systems: [O ] Mount partitions: [ O] Install base system: [O ] Install boot loader: [O ] Reboot: [ E] Comments/Problems: In the default installation mode (linux), the system installs grub as default bootloader. no problems and no error messages during the installation proccess. After reboot comes this message: Grub loading, please wait Error2 Could it be that some of the required modules for this machine wasn`t load/installed at boot time? The same installation (default linux...just press Enter at the boot prompt) on a Toshiba Tecra 8100 completes with no errors. Greetings Jens Voskuhl
