Hello, On Wed, 2 Apr 2008 16:44:37 +0200 Frans Pop wrote: > > Yes. Auto-detecting the cdrom drive works this way. > > OK. That at least identifies the problem, though reverting that change would > not solve all problems as initramfs-tools would still need to be made to > load the driver. > > What we basically need to do here is find a way to identify this type of > system so we can automate the loading of ide-generic. > > BTW, doesn't the installer offer to load additional drivers when it fails to > detect the CD? If it does, what are the dialogs that are displayed?
1. No common CD-ROM drive was detected. You may need to load additional CD-ROM drivers from a driver floppy... Load CD-ROM drivers from a driver floppy? Yes No [Answered with No.] 2. No common CD-ROM drive was detected. Your CD-ROM drive may be an old Mitsumi or another non-IDE, non-SCSI CD-ROM drive. ... Manually select a CD-ROM module and device? Yes No [Answered with No.] 3. An installation step failed. You can try to run the failing item again from the menu, or skip it and choose something else... Continue > Could you also do the following: > - boot the installer > - proceed until the CD fails to be recognized > - switch to VT2 > - what is the output of the following commands at that point: > - ls /proc/bus/* > - ls /sys/bus > - cat /proc/interrupts > - cat /proc/iomem > - cat /proc/ioports > - enter the following commands: > - logger -t DEBUG "Before loading ide-generic" > - modprobe ide-generic > - send the /var/log/syslog at this point > - is there any change in the output of the commands above after that? Output of: ls /proc/bus/* /proc/bus/input: devices handlers /proc/bus/pccard: drivers /proc/bus/pci: 00 devices /proc/bus/usb: Output of: ls /sys/bus MCA acpi eisa ide isa pci pci_express pcmcia platform pnp scsi serio spi usb Output of: cat /proc/interrupts CPU0 0: 25005 XT-PIC-XT timer 1: 476 XT-PIC-XT i8042 2: 0 XT-PIC-XT cascade 6: 3 XT-PIC-XT floppy 7: 3 XT-PIC-XT parport0 11: 0 XT-PIC-XT yenta, yenta, ohci_hcd:usb1 12: 4 XT-PIC-XT i8042 13: 26 XT-PIC-XT acpi NMI: 0 LOC: 0 ERR: 0 MIS: 0 Output of: cat /proc/iomem 00000000-0009fbff : System RAM 00000000-00000000 : Crash kernel 0009fc00-0009ffff : reserved 000a0000-000bffff : Video RAM area 000c0000-000c97ff : Video ROM 000f0000-000fffff : System ROM 00100000-0200ffff : System RAM 00100000-0029e27a : Kernel code 0029e27b-00340cc3 : Kernel data 02010000-0201ffff : ACPI Tables 02020000-0203ffff : reserved 10000000-13ffffff : PCI CardBus #01 14000000-17ffffff : PCI CardBus #01 18000000-1bffffff : PCI CardBus #05 1c000000-1fffffff : PCI CardBus #05 20000000-2003ffff : 0000:00:04.0 20040000-20040fff : 0000:00:13.0 20040000-20040fff : yenta_socket 20041000-20041fff : 0000:00:13.1 20041000-20041fff : yenta_socket fcfff000-fcffffff : 0000:00:0b.0 fcfff000-fcffffff : ohci_hcd fd000000-fdffffff : 0000:00:04.0 fef80000-feffffff : reserved fffe0000-fffe6dff : reserved fffe6e00-fffe6fff : ACPI Non-volatile Storage fffe7000-ffffffff : reserved Output of: cat /proc/ioports 0000-001f : dma1 0020-0021 : pic1 0040-0043 : timer0 0050-0053 : timer1 0060-006f : keyboard 0080-008f : dma page reg 00a0-00a1 : pic2 00c0-00df : dma2 00f0-00ff : fpu 0378-037a : parport0 03c0-03df : vga+ 03f2-03f5 : floppy 03f7-03f7 : floppy DIR 03f8-03ff : serial 0778-077a : parport0 0cf8-0cff : PCI conf1 1000-10ff : PCI CardBus #01 1400-14ff : PCI CardBus #01 1800-18ff : PCI CardBus #05 18a0-18a3 : ACPI PM1a_EVT_BLK 18a4-18a5 : ACPI PM1a_CNT_BLK 18a6-18a6 : ACPI PM2_CNT_BLK 18a8-18ab : ACPI PM_TMR 18ac-18af : ACPI GPE0_BLK 18b0-18b5 : ACPI CPU throttle 1c00-1cff : PCI CardBus #05 ffe0-ffff : 0000:00:11.0 [Executed "logger -t DEBUG "Before loading ide-generic" and "modprobe ide-generic" ] After that: Output of: /var/log/syslog [see attached file "syslog" ] Output of: ls /proc/bus/* [the same as above] Output of: ls /sys/bus [the same as above] Output of: cat /proc/interrupts CPU0 0: 31540 XT-PIC-XT timer 1: 1095 XT-PIC-XT i8042 2: 0 XT-PIC-XT cascade 6: 3 XT-PIC-XT floppy 7: 3 XT-PIC-XT parport0 11: 0 XT-PIC-XT yenta, yenta, ohci_hcd:usb1 12: 4 XT-PIC-XT i8042 13: 36 XT-PIC-XT acpi 14: 491 XT-PIC-XT ide0 15: 27 XT-PIC-XT ide1 NMI: 0 LOC: 0 ERR: 0 MIS: 0 Output of: cat /proc/iomem [the same as above] Output of: cat /proc/ioports 0000-001f : dma1 0020-0021 : pic1 0040-0043 : timer0 0050-0053 : timer1 0060-006f : keyboard 0080-008f : dma page reg 00a0-00a1 : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 0376-0376 : ide1 0378-037a : parport0 03c0-03df : vga+ 03f2-03f5 : floppy 03f6-03f6 : ide0 03f7-03f7 : floppy DIR 03f8-03ff : serial 0778-077a : parport0 0cf8-0cff : PCI conf1 1000-10ff : PCI CardBus #01 1400-14ff : PCI CardBus #01 1800-18ff : PCI CardBus #05 18a0-18a3 : ACPI PM1a_EVT_BLK 18a4-18a5 : ACPI PM1a_CNT_BLK 18a6-18a6 : ACPI PM2_CNT_BLK 18a8-18ab : ACPI PM_TMR 18ac-18af : ACPI GPE0_BLK 18b0-18b5 : ACPI CPU throttle 1c00-1cff : PCI CardBus #05 ffe0-ffff : 0000:00:11.0 -- Kind regards Holger ============================================================== Created with Sylpheed 2.3.0 under THE NEW DEBIAN GNU/LINUX 4.0 »Etch« http://counter.li.org/, Registered LinuxUser #311290 Try out OpenGL 3D-Desktop Beryl! www.beryl-project.org =============================================================
Jun 13 11:30:57 syslogd started: BusyBox v1.1.3 Jun 13 11:30:57 kernel: klogd started: BusyBox v1.1.3 (Debian 1:1.1.3-5) Jun 13 11:30:57 kernel: Linux version 2.6.22-3-486 (Debian 2.6.22-6) ([EMAIL PROTECTED]) (gcc version 4.1.3 20071019 (prerelease) (Debian 4.1.2-17)) #1 Mon Nov 12 07:53:08 UTC 2007 Jun 13 11:30:57 kernel: BIOS-provided physical RAM map: Jun 13 11:30:57 kernel: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) Jun 13 11:30:57 kernel: BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) Jun 13 11:30:57 kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) Jun 13 11:30:57 kernel: BIOS-e820: 0000000000100000 - 0000000002010000 (usable) Jun 13 11:30:57 kernel: BIOS-e820: 0000000002010000 - 0000000002020000 (ACPI data) Jun 13 11:30:57 kernel: BIOS-e820: 0000000002020000 - 0000000002040000 (reserved) Jun 13 11:30:57 kernel: BIOS-e820: 00000000fef80000 - 00000000ff000000 (reserved) Jun 13 11:30:57 kernel: BIOS-e820: 00000000fffe0000 - 00000000fffe6e00 (reserved) Jun 13 11:30:57 kernel: BIOS-e820: 00000000fffe6e00 - 00000000fffe7000 (ACPI NVS) Jun 13 11:30:57 kernel: BIOS-e820: 00000000fffe7000 - 0000000100000000 (reserved) Jun 13 11:30:57 kernel: 32MB LOWMEM available. Jun 13 11:30:57 kernel: Entering add_active_range(0, 0, 8208) 0 entries of 256 used Jun 13 11:30:57 kernel: Zone PFN ranges: Jun 13 11:30:57 kernel: DMA 0 -> 4096 Jun 13 11:30:57 kernel: Normal 4096 -> 8208 Jun 13 11:30:57 kernel: early_node_map[1] active PFN ranges Jun 13 11:30:57 kernel: 0: 0 -> 8208 Jun 13 11:30:57 kernel: On node 0 totalpages: 8208 Jun 13 11:30:57 kernel: DMA zone: 32 pages used for memmap Jun 13 11:30:57 kernel: DMA zone: 0 pages reserved Jun 13 11:30:57 kernel: DMA zone: 4064 pages, LIFO batch:0 Jun 13 11:30:57 kernel: Normal zone: 32 pages used for memmap Jun 13 11:30:57 kernel: Normal zone: 4080 pages, LIFO batch:0 Jun 13 11:30:57 kernel: DMI not present or invalid. Jun 13 11:30:57 kernel: ACPI: RSDP 000F4850, 0014 (r0 TOSHIB) Jun 13 11:30:57 kernel: ACPI: RSDT 02010000, 0028 (r1 TOSHIB 750 19980225 TASM 4010000) Jun 13 11:30:57 kernel: ACPI: FACP 02010054, 0074 (r1 TOSHIB 750 19980225 TASM 4010000) Jun 13 11:30:57 kernel: ACPI: DSDT 020100C8, 489F (r1 TOSHIB 300 19990601 MSFT 100000B) Jun 13 11:30:57 kernel: ACPI: FACS FFFE6E00, 0040 Jun 13 11:30:57 kernel: ACPI: PM-Timer IO Port: 0x18a8 Jun 13 11:30:57 kernel: Allocating PCI resources starting at 10000000 (gap: 02040000:fcf40000) Jun 13 11:30:57 kernel: Built 1 zonelists. Total pages: 8144 Jun 13 11:30:57 kernel: Kernel command line: vga=normal initrd=/install.386/initrd.gz rescue/enable=true -- quiet BOOT_IMAGE=/install.386/vmlinuz Jun 13 11:30:57 kernel: No local APIC present or hardware disabled Jun 13 11:30:57 kernel: mapped APIC to ffffd000 (01049000) Jun 13 11:30:57 kernel: Initializing CPU#0 Jun 13 11:30:57 kernel: PID hash table entries: 128 (order: 7, 512 bytes) Jun 13 11:30:57 kernel: Detected 233.291 MHz processor. Jun 13 11:30:57 kernel: Console: colour VGA+ 80x25 Jun 13 11:30:57 kernel: Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Jun 13 11:30:57 kernel: Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Jun 13 11:30:57 kernel: Memory: 25068k/32832k available (1656k kernel code, 7376k reserved, 650k data, 316k init, 0k highmem) Jun 13 11:30:57 kernel: virtual kernel memory layout: Jun 13 11:30:57 kernel: fixmap : 0xfffb5000 - 0xfffff000 ( 296 kB) Jun 13 11:30:57 kernel: vmalloc : 0xc3000000 - 0xfffb3000 ( 975 MB) Jun 13 11:30:57 kernel: lowmem : 0xc0000000 - 0xc2010000 ( 32 MB) Jun 13 11:30:57 kernel: .init : 0xc0344000 - 0xc0393000 ( 316 kB) Jun 13 11:30:57 kernel: .data : 0xc029e27b - 0xc0340cc4 ( 650 kB) Jun 13 11:30:57 kernel: .text : 0xc0100000 - 0xc029e27b (1656 kB) Jun 13 11:30:57 kernel: Checking if this processor honours the WP bit even in supervisor mode... Ok. Jun 13 11:30:57 kernel: Calibrating delay using timer specific routine.. 467.44 BogoMIPS (lpj=934880) Jun 13 11:30:57 kernel: Security Framework v1.0.0 initialized Jun 13 11:30:57 kernel: SELinux: Disabled at boot. Jun 13 11:30:57 kernel: Capability LSM initialized Jun 13 11:30:57 kernel: Mount-cache hash table entries: 512 Jun 13 11:30:57 kernel: CPU: After generic identify, caps: 008001bf 00000000 00000000 00000000 00000000 00000000 00000000 Jun 13 11:30:57 kernel: Intel Pentium with F0 0F bug - workaround enabled. Jun 13 11:30:57 kernel: Jun 13 11:30:57 kernel: CPU: After all inits, caps: 008001bf 00000000 00000000 00000000 00000000 00000000 00000000 Jun 13 11:30:57 kernel: Compat vDSO mapped to ffffe000. Jun 13 11:30:57 kernel: CPU: Intel Mobile Pentium MMX stepping 01 Jun 13 11:30:57 kernel: Checking 'hlt' instruction... OK. Jun 13 11:30:57 kernel: ACPI: Core revision 20070126 Jun 13 11:30:57 kernel: ACPI: setting ELCR to 2000 (from 0804) Jun 13 11:30:57 kernel: Booting paravirtualized kernel on bare hardware Jun 13 11:30:57 kernel: NET: Registered protocol family 16 Jun 13 11:30:57 kernel: EISA bus registered Jun 13 11:30:57 kernel: ACPI: bus type pci registered Jun 13 11:30:57 kernel: PCI: PCI BIOS revision 2.10 entry at 0xfd4ce, last bus=21 Jun 13 11:30:57 kernel: PCI: Using configuration type 1 Jun 13 11:30:57 kernel: Setting up standard PCI resources Jun 13 11:30:57 kernel: ACPI: Interpreter enabled Jun 13 11:30:57 kernel: ACPI: (supports S0 S1 S3 S4 S5) Jun 13 11:30:57 kernel: ACPI: Using PIC for interrupt routing Jun 13 11:30:57 kernel: ACPI: PCI Root Bridge [PCI0] (0000:00) Jun 13 11:30:57 kernel: PCI: Probing PCI hardware (bus 00) Jun 13 11:30:57 kernel: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] Jun 13 11:30:57 kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) Jun 13 11:30:57 kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) Jun 13 11:30:57 kernel: >ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) Jun 13 11:30:57 kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) Jun 13 11:30:57 kernel: ACPI: Power Resource [PFAN] (off) Jun 13 11:30:57 kernel: ACPI: Power Resource [SFAN] (off) Jun 13 11:30:57 kernel: ACPI: Power Resource [PWH1] (on) Jun 13 11:30:57 kernel: ACPI: Power Resource [PWH2] (on) Jun 13 11:30:57 kernel: Linux Plug and Play Support v0.97 (c) Adam Belay Jun 13 11:30:57 kernel: pnp: PnP ACPI init Jun 13 11:30:57 kernel: ACPI: bus type pnp registered Jun 13 11:30:57 kernel: PCI: setting IRQ 13 as level-triggered Jun 13 11:30:57 kernel: pnp: PnP ACPI: found 15 devices Jun 13 11:30:57 kernel: ACPI: ACPI bus type pnp unregistered Jun 13 11:30:57 kernel: PnPBIOS: Disabled by ACPI PNP Jun 13 11:30:57 kernel: PCI: Using ACPI for IRQ routing Jun 13 11:30:57 kernel: PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report Jun 13 11:30:57 kernel: NET: Registered protocol family 8 Jun 13 11:30:57 kernel: NET: Registered protocol family 20 Jun 13 11:30:57 kernel: ACPI: RTC can wake from S4 Jun 13 11:30:57 kernel: pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved Jun 13 11:30:57 kernel: pnp: 00:00: iomem range 0xf0000-0xfffff could not be reserved Jun 13 11:30:57 kernel: pnp: 00:00: iomem range 0x100000-0x200ffff could not be reserved Jun 13 11:30:57 kernel: pnp: 00:00: iomem range 0x2010000-0x203ffff could not be reserved Jun 13 11:30:57 kernel: Time: tsc clocksource has been installed. Jun 13 11:30:57 kernel: PCI: Bus 1, cardbus bridge: 0000:00:13.0 Jun 13 11:30:57 kernel: IO window: 00001000-000010ff Jun 13 11:30:57 kernel: IO window: 00001400-000014ff Jun 13 11:30:57 kernel: PREFETCH window: 10000000-13ffffff Jun 13 11:30:57 kernel: MEM window: 14000000-17ffffff Jun 13 11:30:57 kernel: PCI: Bus 5, cardbus bridge: 0000:00:13.1 Jun 13 11:30:57 kernel: IO window: 00001800-000018ff Jun 13 11:30:57 kernel: IO window: 00001c00-00001cff Jun 13 11:30:57 kernel: PREFETCH window: 18000000-1bffffff Jun 13 11:30:57 kernel: MEM window: 1c000000-1fffffff Jun 13 11:30:57 kernel: PCI: Enabling device 0000:00:13.0 (0000 -> 0003) Jun 13 11:30:57 kernel: ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 Jun 13 11:30:57 kernel: PCI: setting IRQ 11 as level-triggered Jun 13 11:30:57 kernel: ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 Jun 13 11:30:57 kernel: PCI: Setting latency timer of device 0000:00:13.0 to 64 Jun 13 11:30:57 kernel: PCI: Enabling device 0000:00:13.1 (0000 -> 0003) Jun 13 11:30:57 kernel: ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 Jun 13 11:30:57 kernel: ACPI: PCI Interrupt 0000:00:13.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 Jun 13 11:30:57 kernel: PCI: Setting latency timer of device 0000:00:13.1 to 64 Jun 13 11:30:57 kernel: NET: Registered protocol family 2 Jun 13 11:30:57 kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes) Jun 13 11:30:57 kernel: TCP established hash table entries: 1024 (order: 1, 8192 bytes) Jun 13 11:30:57 kernel: TCP bind hash table entries: 1024 (order: 0, 4096 bytes) Jun 13 11:30:57 kernel: TCP: Hash tables configured (established 1024 bind 1024) Jun 13 11:30:57 kernel: TCP reno registered Jun 13 11:30:57 kernel: checking if image is initramfs...<6>Switched to high resolution mode on CPU 0 Jun 13 11:30:57 kernel: it is Jun 13 11:30:57 kernel: Freeing initrd memory: 4153k freed Jun 13 11:30:57 kernel: audit: initializing netlink socket (disabled) Jun 13 11:30:57 kernel: audit(1181734252.324:1): initialized Jun 13 11:30:57 kernel: VFS: Disk quotas dquot_6.5.1 Jun 13 11:30:57 kernel: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Jun 13 11:30:57 kernel: io scheduler noop registered Jun 13 11:30:57 kernel: io scheduler anticipatory registered Jun 13 11:30:57 kernel: io scheduler deadline registered Jun 13 11:30:57 kernel: io scheduler cfq registered (default) Jun 13 11:30:57 kernel: Boot video device is 0000:00:04.0 Jun 13 11:30:57 kernel: isapnp: Scanning for PnP cards... Jun 13 11:30:57 kernel: isapnp: No Plug & Play device found Jun 13 11:30:57 kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled Jun 13 11:30:57 kernel: serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Jun 13 11:30:57 kernel: 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Jun 13 11:30:57 kernel: RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize Jun 13 11:30:57 kernel: PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 Jun 13 11:30:57 kernel: serio: i8042 KBD port at 0x60,0x64 irq 1 Jun 13 11:30:57 kernel: serio: i8042 AUX port at 0x60,0x64 irq 12 Jun 13 11:30:57 kernel: mice: PS/2 mouse device common for all mice Jun 13 11:30:57 kernel: EISA: Probing bus 0 at eisa.0 Jun 13 11:30:57 kernel: Cannot allocate resource for EISA slot 1 Jun 13 11:30:57 kernel: EISA: Detected 0 cards. Jun 13 11:30:57 kernel: TCP bic registered Jun 13 11:30:57 kernel: NET: Registered protocol family 1 Jun 13 11:30:57 kernel: NET: Registered protocol family 17 Jun 13 11:30:57 kernel: Using IPI Shortcut mode Jun 13 11:30:57 kernel: Freeing unused kernel memory: 316k freed Jun 13 11:30:57 kernel: input: AT Translated Set 2 keyboard as /class/input/input0 Jun 13 11:30:57 kernel: Yenta: CardBus bridge found at 0000:00:13.0 [1179:0001] Jun 13 11:30:57 kernel: Yenta: ISA IRQ mask 0x06b8, PCI irq 11 Jun 13 11:30:57 kernel: Socket status: 30000007 Jun 13 11:30:57 kernel: Yenta: CardBus bridge found at 0000:00:13.1 [1179:0001] Jun 13 11:30:57 kernel: Yenta: ISA IRQ mask 0x06b8, PCI irq 11 Jun 13 11:30:57 kernel: Socket status: 30000007 Jun 13 11:30:57 kernel: usbcore: registered new interface driver usbfs Jun 13 11:30:57 kernel: usbcore: registered new interface driver hub Jun 13 11:30:57 kernel: usbcore: registered new device driver usb Jun 13 11:30:57 kernel: st 04 USB 1.1 'Open' Host Controller (OHCI) Driver Jun 13 11:30:57 kernel: ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 Jun 13 11:30:57 kernel: ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 Jun 13 11:30:57 kernel: ohci_hcd 0000:00:0b.0: OHCI Host Controller Jun 13 11:30:57 kernel: ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1 Jun 13 11:30:57 kernel: ohci_hcd 0000:00:0b.0: irq 11, io mem 0xfcfff000 Jun 13 11:30:57 kernel: Floppy drive(s): fd0 is 1.44M Jun 13 11:30:57 kernel: usb usb1: configuration #1 chosen from 1 choice Jun 13 11:30:57 kernel: hub 1-0:1.0: USB hub found Jun 13 11:30:57 kernel: hub 1-0:1.0: 2 ports detected Jun 13 11:30:57 kernel: parport_pc 00:0d: reported by Plug and Play ACPI Jun 13 11:30:57 kernel: parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA] Jun 13 11:30:57 kernel: FDC 0 is an 8272A Jun 13 11:30:57 kernel: cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x1f0-0x1f7 0x220-0x22f 0x330-0x337 0x370-0x37f 0x388-0x38f Jun 13 11:30:57 kernel: cs: IO port probe 0x3e0-0x4ff: excluding 0x480-0x48f 0x4d0-0x4d7 Jun 13 11:30:57 kernel: cs: IO port probe 0x820-0x8ff: clean. Jun 13 11:30:57 kernel: cs: IO port probe 0xc00-0xcf7: clean. Jun 13 11:30:57 kernel: cs: IO port probe 0xa00-0xaff: clean. Jun 13 11:30:57 kernel: cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x1f0-0x1f7 0x220-0x22f 0x330-0x337 0x370-0x37f 0x388-0x38f Jun 13 11:30:57 kernel: cs: IO port probe 0x3e0-0x4ff: excluding 0x480-0x48f 0x4d0-0x4d7 Jun 13 11:30:57 kernel: cs: IO port probe 0x820-0x8ff: clean. Jun 13 11:30:57 kernel: cs: IO port probe 0xc00-0xcf7: clean. Jun 13 11:30:57 kernel: cs: IO port probe 0xa00-0xaff: clean. Jun 13 11:30:57 kernel: ACPI: Transitioning device [FAN] to D3 Jun 13 11:30:57 kernel: ACPI: Transitioning device [FAN] to D3 Jun 13 11:30:57 kernel: ACPI: Fan [FAN] (off) Jun 13 11:30:57 kernel: ACPI: Transitioning device [FNS] to D3 Jun 13 11:30:57 kernel: ACPI: Transitioning device [FNS] to D3 Jun 13 11:30:57 kernel: ACPI: Fan [FNS] (off) Jun 13 11:30:57 kernel: ACPI: Processor [CPU0] (supports 16 throttling states) Jun 13 11:30:57 kernel: ACPI: Thermal Zone [THRM] (27 C) Jun 13 11:30:58 lowmem: Entering low memory mode Jun 13 11:31:00 anna-install: Queueing udeb lowmem for later installation Jun 13 11:31:00 frontend: Obsolete command TITLE Low memory called Jun 13 11:31:11 anna-install: Queueing udeb rescue-mode for later installation Jun 13 11:31:11 init: Starting pid 860, console /dev/tty1: '/sbin/debian-installer' Jun 13 11:31:11 init: Starting pid 863, console /dev/tty4: '/usr/bin/tail' Jun 13 11:31:11 debconf: Setting debconf/language to en Jun 13 11:31:11 main-menu[899]: DEBUG: resolver (libc6): package doesn't exist (ignored) Jun 13 11:31:12 main-menu[899]: INFO: Menu item 'localechooser' selected Jun 13 11:31:12 debconf: Setting debconf/language to en Jun 13 11:31:12 localechooser: info: Locale has been preseeded to C Jun 13 11:31:12 localechooser: info: Set languagechooser/language-name-latin = 'C' Jun 13 11:31:12 localechooser: info: LANGNAME=C Jun 13 11:31:12 localechooser: info: line=C;0;en;;C; Jun 13 11:31:12 localechooser: info: Set debian-installer/language = 'en' Jun 13 11:31:12 localechooser: info: Set debian-installer/locale = 'C' Jun 13 11:31:12 localechooser: info: Set debian-installer/fallbacklocale = 'C' Jun 13 11:31:12 localechooser: info: No default country; preserving current value '' Jun 13 11:31:12 localechooser: info: Set debian-installer/consoledisplay = '' Jun 13 11:31:12 debconf: Setting debconf/language to en Jun 13 11:31:12 localechooser: info: Set debconf/language = 'en' Jun 13 11:31:24 localechooser: info: Set debian-installer/country = 'DE' Jun 13 11:31:24 localechooser: info: Set debian-installer/locale = 'C' Jun 13 11:31:24 main-menu[899]: DEBUG: resolver (libc6): package doesn't exist (ignored) Jun 13 11:31:24 main-menu[899]: INFO: Menu item 'kbd-chooser' selected Jun 13 11:31:24 main-menu[899]: INFO: Falling back to the package description for console-keymaps-at Jun 13 11:31:24 main-menu[899]: INFO: Falling back to the package description for console-keymaps-at Jun 13 11:31:24 kbd-chooser[1102]: DEBUG: Mounting usbdevfs to look for kbd Jun 13 11:31:24 kbd-chooser[1102]: DEBUG: Parsing /proc/bus/usb/devices Jun 13 11:31:24 kbd-chooser[1102]: DEBUG: Adding generic entry for AT keymaps Jun 13 11:31:24 kbd-chooser[1102]: INFO: keyboard type at: present: true: Jun 13 11:31:24 kbd-chooser[1102]: INFO: keyboard type at: present: unknown Jun 13 11:31:24 kbd-chooser[1102]: INFO: Setting debian-installer/serial-console to false Jun 13 11:31:24 kbd-chooser[1102]: INFO: Setting debian-installer/uml-console to false Jun 13 11:31:24 kbd-chooser[1102]: INFO: kbd-chooser: arch at selected Jun 13 11:31:26 kbd-chooser[1102]: INFO: choose_keymap: keymap = de-latin1-nodeadkeys Jun 13 11:31:26 kbd-chooser[1102]: INFO: kbd_chooser: setting keymap de-latin1-nodeadkeys Jun 13 11:31:26 main-menu[899]: DEBUG: resolver (libc6): package doesn't exist (ignored) Jun 13 11:31:26 main-menu[899]: INFO: Menu item 'cdrom-detect' selected Jun 13 11:31:27 net/hw-detect.hotplug: Detected hotpluggable network interface lo Jun 13 11:31:29 hw-detect: Detected module 'usb-storage' for 'USB storage' Jun 13 11:31:30 kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 Jun 13 11:31:30 kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Jun 13 11:31:30 kernel: ide0: generic PnP IDE interface Jun 13 11:31:30 kernel: ide1: generic PnP IDE interface Jun 13 11:31:30 hw-detect: insmod /lib/modules/2.6.22-3-486/kernel/drivers/ide/ide-core.ko Jun 13 11:31:30 kernel: SCSI subsystem initialized Jun 13 11:31:30 kernel: Initializing USB Mass Storage driver... Jun 13 11:31:30 kernel: usbcore: registered new interface driver usb-storage Jun 13 11:31:30 kernel: USB Mass Storage support registered. Jun 13 11:31:30 hw-detect: insmod /lib/modules/2.6.22-3-486/kernel/drivers/scsi/scsi_mod.ko Jun 13 11:31:30 hw-detect: insmod /lib/modules/2.6.22-3-486/kernel/drivers/usb/storage/usb-storage.ko Jun 13 11:31:30 hw-detect: PCMCIA bridge driver already present in kernel Jun 13 11:31:30 hw-detect: Detected PCMCIA, installing pcmciautils. Jun 13 11:31:30 apt-install: Queueing package pcmciautils for later installation Jun 13 11:31:30 apt-install: Queueing package udev for later installation Jun 13 11:31:30 apt-install: Queueing package usbutils for later installation Jun 13 11:31:30 apt-install: Queueing package acpi for later installation Jun 13 11:31:30 apt-install: Queueing package acpid for later installation Jun 13 11:31:30 apt-install: Queueing package acpi-support-base for later installation Jun 13 11:31:33 net/hw-detect.hotplug: Detected hotpluggable network interface lo Jun 13 11:31:35 cdrom-detect: Searching for Debian installation media... Jun 13 11:34:49 cdrom-detect: CDROM-detect failed; unmounting CD just to be sure Jun 13 11:34:49 main-menu[899]: WARNING **: Configuring 'cdrom-detect' failed with error code 1 Jun 13 11:34:49 main-menu[899]: WARNING **: Menu item 'cdrom-detect' failed. Jun 13 11:34:51 main-menu[899]: INFO: Modifying debconf priority limit from 'high' to 'medium' Jun 13 11:34:51 debconf: Setting debconf/priority to medium Jun 13 11:34:51 main-menu[899]: DEBUG: resolver (libc6): package doesn't exist (ignored) Jun 13 11:35:05 main-menu[899]: INFO: Menu item 'cdrom-detect' selected Jun 13 11:35:06 net/hw-detect.hotplug: Detected hotpluggable network interface lo Jun 13 11:35:08 hw-detect: PCMCIA bridge driver already present in kernel Jun 13 11:35:11 net/hw-detect.hotplug: Detected hotpluggable network interface lo Jun 13 11:35:13 cdrom-detect: Searching for Debian installation media... Jun 13 11:35:26 cdrom-detect: CDROM-detect failed; unmounting CD just to be sure Jun 13 11:35:26 main-menu[899]: WARNING **: Configuring 'cdrom-detect' failed with error code 1 Jun 13 11:35:26 main-menu[899]: WARNING **: Menu item 'cdrom-detect' failed. Jun 13 11:36:02 main-menu[899]: INFO: Modifying debconf priority limit from 'medium' to 'low' Jun 13 11:36:02 debconf: Setting debconf/priority to low Jun 13 11:36:02 main-menu[899]: DEBUG: resolver (libc6): package doesn't exist (ignored) Jun 13 11:36:36 init: Starting pid 864, console /dev/tty2: '/bin/sh' Jun 13 11:39:12 DEBUG: Before loading ide-generic Jun 13 11:39:18 kernel: Probing IDE interface ide0... Jun 13 11:39:18 kernel: hda: TOSHIBA MK4006MAV, ATA DISK drive Jun 13 11:39:19 kernel: Probing IDE interface ide1... Jun 13 11:39:19 kernel: hdc: CD-220EA, ATAPI CD/DVD-ROM drive Jun 13 11:39:20 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Jun 13 11:39:20 kernel: ide1 at 0x170-0x177,0x376 on irq 15 Jun 13 11:39:20 kernel: hda: max request size: 128KiB Jun 13 11:39:20 kernel: hda: 8007552 sectors (4099 MB), CHS=7944/16/63 Jun 13 11:39:20 kernel: hda: cache flushes not supported Jun 13 11:39:20 kernel: hda6 > Jun 13 11:39:20 kernel: hdc: ATAPI 20X CD-ROM drive, 128kB Cache Jun 13 11:39:20 kernel: Uniform CD-ROM driver Revision: 3.20