Your message dated Mon, 30 Jun 2008 11:21:00 +0200
with message-id <[EMAIL PROTECTED]>
and subject line Re: linux-image-2.6.22-3-686: Random reading errors when
reading from usb disk with ehci
has caused the Debian Bug report #472696,
regarding linux-image-2.6.22-3-686: Random reading errors when reading from usb
disk with ehci
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact [EMAIL PROTECTED]
immediately.)
--
472696: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=472696
Debian Bug Tracking System
Contact [EMAIL PROTECTED] with problems
--- Begin Message ---
Package: linux-image-2.6.22-3-686
Version: 2.6.22-6.lenny1
Severity: important
There seems to be random reading errors when reading from my Seagate FreeAgent
500GB external USB hard drive. It becomes clear by an example:
# md5sum -c test02.avi.md5 ; md5sum -c test02.avi.md5 ; md5sum -c
test02.avi.md5 ; md5sum -c test02.avi.md5 ; md5sum -c test02.avi.md5 ; md5sum
-c test02.avi.md5 ; md5sum -c test02.avi.md5 ; md5sum -c test02.avi.md5
test02.avi: OK
test02.avi: FAILED
md5sum: WARNING: 1 of 1 computed checksum did NOT match
test02.avi: OK
test02.avi: OK
test02.avi: OK
test02.avi: OK
test02.avi: OK
test02.avi: FAILED
md5sum: WARNING: 1 of 1 computed checksum did NOT match
test02.avi is a file on device sda3 from the kernel log. When issuing a rmmod
ehci_hcd, the same command returns OK every time.
Please let me know if I can be of any help. I would really like to see this
issue resolved.
-- Package-specific info:
** Version:
Linux version 2.6.22-3-686 (Debian 2.6.22-6.lenny1) ([EMAIL PROTECTED]) (gcc
version 4.1.3 20071209 (prerelease) (Debian 4.1.2-18)) #1 SMP Sun Feb 10
20:20:49 UTC 2008
** Not tainted
** Kernel log:
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
r8169: eth0: link up
eth0: no IPv6 routers present
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ehci_hcd 0000:02:06.2: remove, state 1
usb usb7: USB disconnect, address 1
usb 7-3: USB disconnect, address 2
ehci_hcd 0000:02:06.2: USB bus 7 deregistered
ACPI: PCI interrupt for device 0000:02:06.2 disabled
usb 6-1: new full speed USB device using uhci_hcd and address 3
usb 6-1: configuration #1 chosen from 1 choice
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 4:0:0:0: Direct-Access Seagate FreeAgentDesktop 100F PQ: 0 ANSI: 4
sd 4:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Mode Sense: 1c 00 00 00
sd 4:0:0:0: [sda] Assuming drive cache: write through
sd 4:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Mode Sense: 1c 00 00 00
sd 4:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2 sda3
sd 4:0:0:0: [sda] Attached SCSI disk
** Loaded modules:
Module Size Used by
ehci_hcd 30796 0
binfmt_misc 11112 1
rfcomm 36280 2
l2cap 22432 9 rfcomm
bluetooth 49348 4 rfcomm,l2cap
ppdev 8676 0
lp 10980 0
ipv6 236964 16
firewire_sbp2 12100 0
loop 16932 0
sd_mod 27136 2
snd_intel8x0 32124 1
snd_ac97_codec 92836 1 snd_intel8x0
usblp 13280 0
parport_pc 33828 1
ac97_bus 2272 1 snd_ac97_codec
snd_pcm_oss 39200 0
snd_mixer_oss 15424 1 snd_pcm_oss
parport 33928 3 ppdev,lp,parport_pc
snd_pcm 72324 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 21028 1 snd_pcm
snd 48324 8
snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 7520 1 snd
snd_page_alloc 10056 2 snd_intel8x0,snd_pcm
rtc 12856 0
i2c_i801 8656 0
i2c_core 23552 1 i2c_i801
iTCO_wdt 9924 0
intel_agp 23188 1
agpgart 31880 1 intel_agp
shpchp 31060 0
pci_hotplug 29184 1 shpchp
tsdev 7968 0
evdev 9312 1
ext3 121288 3
jbd 55336 1 ext3
mbcache 8260 1 ext3
ide_cd 36416 0
cdrom 32832 1 ide_cd
ide_disk 16512 5
ata_generic 7556 0
ata_piix 13348 0
libata 115984 2 ata_generic,ata_piix
usb_storage 76576 1
scsi_mod 136620 4 firewire_sbp2,sd_mod,libata,usb_storage
usbhid 25792 0
hid 25248 1 usbhid
floppy 54884 0
generic 4836 0 [permanent]
piix 8868 0 [permanent]
ide_core 113764 5 ide_cd,ide_disk,usb_storage,generic,piix
firewire_ohci 16512 0
firewire_core 39008 2 firewire_sbp2,firewire_ohci
crc_itu_t 2144 1 firewire_core
r8169 28872 0
uhci_hcd 22960 0
usbcore 125384 6 ehci_hcd,usblp,usb_storage,usbhid,uhci_hcd
thermal 13416 0
processor 31176 1 thermal
fan 4836 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82865G/PE/P DRAM
Controller/Host-Hub Interface [8086:2570] (rev 02)
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:01.0 PCI bridge [0604]: Intel Corporation 82865G/PE/P PCI to AGP Controller
[8086:2571] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: f0000000-f7ffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #1 [8086:24d2] (rev 02) (prog-if 00 [UHCI])
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at bc00 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #2 [8086:24d4] (rev 02) (prog-if 00 [UHCI])
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at b000 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #3 [8086:24d7] (rev 02) (prog-if 00 [UHCI])
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at b400 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #4 [8086:24de] (rev 02) (prog-if 00 [UHCI])
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at b800 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
c2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 30000000-300fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:1f.0 ISA bridge [0601]: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC
Interface Bridge [8086:24d0] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 0
Kernel modules: intel-rng, iTCO_wdt
00:1f.1 IDE interface [0101]: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE
Controller [8086:24db] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at f000 [size=16]
Region 5: Memory at 30100000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: PIIX_IDE
Kernel modules: piix
00:1f.2 IDE interface [0101]: Intel Corporation 82801EB (ICH5) SATA Controller
[8086:24d1] (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at c000 [size=8]
Region 1: I/O ports at c400 [size=4]
Region 2: I/O ports at c800 [size=8]
Region 3: I/O ports at cc00 [size=4]
Region 4: I/O ports at d000 [size=16]
Kernel driver in use: ata_piix
Kernel modules: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus
Controller [8086:24d3] (rev 02)
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 22
Region 4: I/O ports at 0500 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801EB/ER
(ICH5/ICH5R) AC'97 Audio Controller [8086:24d5] (rev 02)
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 22
Region 0: I/O ports at d800 [size=256]
Region 1: I/O ports at dc00 [size=64]
Region 2: Memory at fc000000 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at fc001000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV34 [GeForce FX
5200] [10de:0322] (rev a1) (prog-if 00 [VGA controller])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M]
[virtual] Expansion ROM at f9000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: nvidiafb
02:02.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8169
Gigabit Ethernet [10ec:8169] (rev 10)
Subsystem: ABIT Computer Corp. Unknown device [147b:102f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 16000ns max), Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at a000 [size=256]
Region 1: Memory at fb000000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 30000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
02:06.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller [1106:3038] (rev 61) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
[1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at a400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
02:06.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller [1106:3038] (rev 61) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
[1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at a800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
02:06.2 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev
63) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0 [1106:3104]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 128 bytes
Interrupt: pin C routed to IRQ 21
Region 0: Memory at fb001000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
02:06.3 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. IEEE 1394 Host
Controller [1106:3044] (rev 46) (prog-if 10 [OHCI])
Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller [1106:3044]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fb002000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at ac00 [size=128]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.22-3-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.22-3-686 depends on:
ii initramfs-tools [linux-initr 0.91e tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.22-3-686 recommends:
ii libc6-i686 2.7-6 GNU C Library: Shared libraries [i
-- debconf information:
linux-image-2.6.22-3-686/postinst/bootloader-test-error-2.6.22-3-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.22-3-686/preinst/lilo-initrd-2.6.22-3-686: true
linux-image-2.6.22-3-686/prerm/would-invalidate-boot-loader-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/overwriting-modules-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/elilo-initrd-2.6.22-3-686: true
linux-image-2.6.22-3-686/postinst/kimage-is-a-directory:
linux-image-2.6.22-3-686/preinst/lilo-has-ramdisk:
linux-image-2.6.22-3-686/postinst/old-initrd-link-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/initrd-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/old-system-map-link-2.6.22-3-686: true
* linux-image-2.6.22-3-686/preinst/already-running-this-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/depmod-error-2.6.22-3-686: false
linux-image-2.6.22-3-686/postinst/bootloader-error-2.6.22-3-686:
linux-image-2.6.22-3-686/preinst/failed-to-move-modules-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/old-dir-initrd-link-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/abort-install-2.6.22-3-686:
linux-image-2.6.22-3-686/preinst/abort-overwrite-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/depmod-error-initrd-2.6.22-3-686: false
linux-image-2.6.22-3-686/preinst/bootloader-initrd-2.6.22-3-686: true
linux-image-2.6.22-3-686/prerm/removing-running-kernel-2.6.22-3-686: true
linux-image-2.6.22-3-686/postinst/create-kimage-link-2.6.22-3-686: true
--- End Message ---
--- Begin Message ---
On Mon, 30 Jun 2008, Tarje Killingberg wrote:
> I am sorry, but I do not know as I replaced both my OS and my hardware some
> time in April. All I know is that with my new hardware, and Ubuntu 8.04, it
> works perfectly.
>
> --
> Tarje
ok thanks for quick feedback. assuming fixed.
enjoy your Linux boxes.
best regards
--
maks
--- End Message ---
