Your message dated Sun, 15 Mar 2009 08:07:23 GMT
with message-id <[email protected]>
and subject line madwifi has been removed from Debian, closing #474617
has caused the Debian Bug report #474617,
regarding network down and ksoftirqd takes 100% of CPU
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact [email protected]
immediately.)
--
474617: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=474617
Debian Bug Tracking System
Contact [email protected] with problems
--- Begin Message ---
Subject: madwifi-source: network down and ksoftirqd take 100% of CPU
Package: madwifi-source
Version: 1:0.9.4~rc2-1
Severity: normal
*** Please type your report below this line ***
Hi,
Network down often and ksoftirqd0/1 take 100% of CPU.
I'm using a netgear wpn311 wireless PCI adapter.
lspci -v
02:01.0 Ethernet controller: Atheros Communications, Inc. AR5212/AR5213
Multiprotocol MAC/baseband processor (rev 01)
Subsystem: Netgear Unknown device 5e00
Flags: bus master, medium devsel, latency 168, IRQ 16
Memory at fdee0000 (32-bit, non-prefetchable)
[size=64K]
Capabilities: <access denied>
Kernel driver in use: ath_pci
Kernel modules: ath_pci,ath5k
dmesg
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413,
RF5413)
wlan: 0.9.4
ath_pci: 0.9.4
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 16 (level, low) -> IRQ 16
ath_rate_sample: 1.2 (0.9.4)
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps
24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 7.9 phy 4.5 radio 5.6
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Atheros 5212: mem=0xfdee0000, irq=16
when the problem occurs, dmesg return this message:
wifi0: rx FIFO overrun; resetting
wifi0: ath_reset: unable to reset hardware: 'Hardware didn't respond as
expected' (HAL status 3)
I do "/etc/init.d/network restart" to resolve the problem, network restart
and ksoftirq returns to sleeping mode.
This problem happens 5 to 6 times during the day.
This is the same problem that this ticket: http://madwifi.org/ticket/1835
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.24-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages madwifi-source depends on:
ii bzip2 1.0.5-0.1 high-quality block-sorting
file co
ii debhelper 6.0.5 helper programs for
debian/rules
ii module-assistant 0.10.11.0 tool to make module package
creati
madwifi-source recommends no packages.
-- no debconf information
--- End Message ---
--- Begin Message ---
Version: 1:0.9.4+r3772.20080716-1+rm
The madwifi package has been removed from Debian so we are closing
the bugs that were still opened against it.
For more information about this package's removal, read
http://bugs.debian.org/519446 . That bug might give the reasons why
this package was removed, and suggestions of possible replacements.
Don't hesitate to reply to this mail if you have any question.
Thank you for your contribution to Debian.
Kind regards,
--
Marco Rodrigues
--- End Message ---
