--- Begin Message ---
Package: src:linux
Version: 4.5.1-1
Severity: normal
Dear Maintainer,
* What led up to the situation?
Upgrading to newer 4.x kernel versions
* What exactly did you do (or not do) that was effective (or
ineffective)?
""
* What was the outcome of this action?
Asus MyCinema U3100 Mini Plus V2 USB DVB-T Stick won't work any longer. It
is recognised by the kernel, but Me-TV won't recognise it.
* What outcome did you expect instead?
Working DVB-T stick
since newer kernel versions (actually using linux kernel v4.5) my Asus MyCinema
U3100 Mini Plus V2 USB DVB-T Stick won't work any longer.
Here is the output of syslog:
Apr 30 05:34:14 g6 kernel: [ 6036.453857] usb 2-2.3: USB disconnect, device
number 5
Apr 30 05:34:15 g6 kernel: [ 6037.615546] usb 2-2.3: new high-speed USB device
number 11 using xhci_hcd
Apr 30 05:34:15 g6 kernel: [ 6037.718847] usb 2-2.3: New USB device found,
idVendor=1b80, idProduct=d3a8
Apr 30 05:34:15 g6 kernel: [ 6037.718853] usb 2-2.3: New USB device strings:
Mfr=1, Product=2, SerialNumber=0
Apr 30 05:34:15 g6 kernel: [ 6037.718855] usb 2-2.3: Product: Rtl2832UDVB
Apr 30 05:34:15 g6 kernel: [ 6037.718857] usb 2-2.3: Manufacturer: Realtek
Apr 30 05:34:15 g6 mtp-probe: checking bus 2, device 11:
"/sys/devices/pci0000:00/0000:00:1c.0/0000:10:00.0/usb2/2-2/2-2.3"
Apr 30 05:34:15 g6 mtp-probe: bus: 2, device: 11 was not an MTP device
The USB DVB-T stick is recognised but Me-TV shows no tuner found. Worked fine
before on older kernel versions.
Thank you very much for your kind reply.
With many freetings,
Adrian Immanuel Kieß
http://www.immanuelK.net
-- Package-specific info:
** Version:
Linux version 4.5.0-1-amd64 ([email protected]) (gcc version 5.3.1
20160409 (Debian 5.3.1-14) ) #1 SMP Debian 4.5.1-1 (2016-04-14)
** Command line:
BOOT_IMAGE=/vmlinuz-4.5.0-1-amd64
root=UUID=96d5fdb9-5d4e-46f2-89e3-34fcfc7bfe14 ro splash vga=795 splash vga=775
resume=/dev/sdc2
** Tainted: E (8192)
* Unsigned module has been loaded (currently expected).
** Kernel log:
[ 16.174129] bluetooth hci0: Direct firmware load for
brcm/BCM20702A1-0a5c-21e8.hcd failed with error -2
[ 16.174131] Bluetooth: hci0: BCM: Patch brcm/BCM20702A1-0a5c-21e8.hcd not
found
[ 16.281385] usbcore: registered new interface driver snd-usb-audio
[ 16.325945] iTCO_vendor_support: vendor-support=0
[ 16.326633] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 16.326664] iTCO_wdt: Found a 3420 TCO device (Version=2, TCOBASE=0x1060)
[ 16.326686] watchdog: iTCO_wdt: cannot register miscdev on minor=130
(err=-16).
[ 16.326686] watchdog: iTCO_wdt: a legacy watchdog module is probably present.
[ 16.326734] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 16.788687] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
user_xattr
[ 16.940535] Adding 34814972k swap on /dev/sdd2. Priority:100 extents:1
across:34814972k FS
[ 16.983627] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts:
user_xattr
[ 34.930411] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts:
user_xattr
[ 38.474404] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts:
user_xattr,usrquota
[ 39.014054] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 39.534567] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 39.542180] Bluetooth: BNEP filters: protocol multicast
[ 39.549881] Bluetooth: BNEP socket layer initialized
[ 40.550931] tg3 0000:1e:00.0 eth0: Link is up at 100 Mbps, full duplex
[ 40.558823] tg3 0000:1e:00.0 eth0: Flow control is on for TX and on for RX
[ 40.558842] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 40.610426] traps: atop[1476] trap divide error ip:4073c2 sp:7fff5b974970
error:0 in atop[400000+26000]
[ 44.727068] usblp1: removed
[ 44.728722] usblp 1-1.5:1.0: usblp1: USB Bidirectional printer dev 4 if 0
alt 0 proto 2 vid 0x04E8 pid 0x3268
[ 49.383902] RPC: Registered named UNIX socket transport module.
[ 49.383906] RPC: Registered udp transport module.
[ 49.383908] RPC: Registered tcp transport module.
[ 49.383909] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 49.398337] Installing knfsd (copyright (C) 1996 [email protected]).
[ 49.412465] audit: netlink_unicast sending to audit_pid=0 returned error:
-111
[ 49.412471] audit: type=1302 audit(1461981267.051:64661): item=0
name="/usr/lib/pymodules/python2.7/apport_python_hook.pyc" nametype=UNKNOWN
[ 49.412473] audit: type=1327 audit(1461981267.051:64661):
proctitle=2F62696E2F7368002F6574632F696E69742E642F73616D62612D61642D6463007374617274
[ 49.412475] audit: type=1300 audit(1461981267.051:64662): arch=c000003e
syscall=2 success=no exit=-2 a0=205f770 a1=0 a2=1b6 a3=0 items=1 ppid=2172
pid=2177 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0
fsgid=0 tty=(none) ses=4294967295 comm="samba-tool" exe="/usr/bin/python2.7"
key=(null)
[ 49.412476] audit: type=1307 audit(1461981267.051:64662): cwd="/"
[ 49.412478] audit: type=1302 audit(1461981267.051:64662): item=0
name="/usr/lib/python2.7/dist-packages/wx-3.0-gtk2/apport_python_hook.x86_64-linux-gnu.so"
nametype=UNKNOWN
[ 49.412479] audit: type=1327 audit(1461981267.051:64662):
proctitle=2F62696E2F7368002F6574632F696E69742E642F73616D62612D61642D6463007374617274
[ 49.412481] audit: type=1300 audit(1461981267.051:64663): arch=c000003e
syscall=2 success=no exit=-2 a0=205f770 a1=0 a2=1b6 a3=0 items=1 ppid=2172
pid=2177 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0
fsgid=0 tty=(none) ses=4294967295 comm="samba-tool" exe="/usr/bin/python2.7"
key=(null)
[ 49.412483] audit: type=1307 audit(1461981267.051:64663): cwd="/"
[ 49.412484] audit: type=1302 audit(1461981267.051:64663): item=0
name="/usr/lib/python2.7/dist-packages/wx-3.0-gtk2/apport_python_hook.so"
nametype=UNKNOWN
[ 49.412486] audit: type=1327 audit(1461981267.051:64663):
proctitle=2F62696E2F7368002F6574632F696E69742E642F73616D62612D61642D6463007374617274
[ 49.449284] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
directory
[ 49.450206] NFSD: starting 90-second grace period (net ffffffff81ad8140)
[ 50.053168] usb 2-2.1: USB disconnect, device number 4
[ 50.053173] usb 2-2.1.1: USB disconnect, device number 6
[ 50.128390] usb 2-2.1.2: USB disconnect, device number 7
[ 50.130117] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 50.150396] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 50.185605] Ebtables v2.0 registered
[ 50.433576] bridge: automatic filtering via arp/ip/ip6tables has been
deprecated. Update your scripts to load br_netfilter if you need this.
[ 50.442222] tun: Universal TUN/TAP device driver, 1.6
[ 50.442225] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 50.504476] device virbr0-nic entered promiscuous mode
[ 50.651602] nf_conntrack version 0.5.0 (65536 buckets, 262144 max)
[ 50.687078] virbr0: port 1(virbr0-nic) entered listening state
[ 50.687092] virbr0: port 1(virbr0-nic) entered listening state
[ 50.729291] virbr0: port 1(virbr0-nic) entered disabled state
[ 50.732137] device virbr0-nic left promiscuous mode
[ 50.732154] virbr0: port 1(virbr0-nic) entered disabled state
[ 50.804467] usb 2-2.1: new high-speed USB device number 8 using xhci_hcd
[ 50.893519] usb 2-2.1: New USB device found, idVendor=03f0, idProduct=2824
[ 50.893524] usb 2-2.1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 50.894961] hub 2-2.1:1.0: USB hub found
[ 50.895291] hub 2-2.1:1.0: 2 ports detected
[ 51.172398] usb 2-2.1.1: new low-speed USB device number 9 using xhci_hcd
[ 51.286731] usb 2-2.1.1: New USB device found, idVendor=03f0, idProduct=1198
[ 51.286738] usb 2-2.1.1: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 51.286742] usb 2-2.1.1: Product: HP USB 1000dpi Laser Mouse
[ 51.286745] usb 2-2.1.1: Manufacturer: HP
[ 51.293437] input: HP HP USB 1000dpi Laser Mouse as
/devices/pci0000:00/0000:00:1c.0/0000:10:00.0/usb2/2-2/2-2.1/2-2.1.1/2-2.1.1:1.0/0003:03F0:1198.0008/input/input9
[ 51.348713] hid-generic 0003:03F0:1198.0008: input,hidraw3: USB HID v2.00
Mouse [HP HP USB 1000dpi Laser Mouse] on usb-0000:10:00.0-2.1.1/input0
[ 51.352602] hid-generic 0003:03F0:1198.0009: hiddev0,hidraw4: USB HID v2.00
Device [HP HP USB 1000dpi Laser Mouse] on usb-0000:10:00.0-2.1.1/input1
[ 51.424377] usb 2-2.1.2: new full-speed USB device number 10 using xhci_hcd
[ 51.541558] usb 2-2.1.2: New USB device found, idVendor=03f0, idProduct=164a
[ 51.541564] usb 2-2.1.2: New USB device strings: Mfr=1, Product=2,
SerialNumber=7
[ 51.541566] usb 2-2.1.2: Product: HP SC Keyboard - Apollo (Liteon)
[ 51.541568] usb 2-2.1.2: Manufacturer: Liteon
[ 51.541570] usb 2-2.1.2: SerialNumber: 05071300005626
[ 51.548668] input: Liteon HP SC Keyboard - Apollo (Liteon) as
/devices/pci0000:00/0000:00:1c.0/0000:10:00.0/usb2/2-2/2-2.1/2-2.1.2/2-2.1.2:1.0/0003:03F0:164A.000A/input/input10
[ 51.604897] hid-generic 0003:03F0:164A.000A: input,hidraw5: USB HID v1.10
Keyboard [Liteon HP SC Keyboard - Apollo (Liteon)] on
usb-0000:10:00.0-2.1.2/input0
[ 51.611494] input: Liteon HP SC Keyboard - Apollo (Liteon) as
/devices/pci0000:00/0000:00:1c.0/0000:10:00.0/usb2/2-2/2-2.1/2-2.1.2/2-2.1.2:1.2/0003:03F0:164A.000B/input/input11
[ 51.664876] hid-generic 0003:03F0:164A.000B: input,hidraw6: USB HID v1.10
Device [Liteon HP SC Keyboard - Apollo (Liteon)] on
usb-0000:10:00.0-2.1.2/input2
[ 66.192467] Bluetooth: RFCOMM TTY layer initialized
[ 66.192475] Bluetooth: RFCOMM socket layer initialized
[ 66.192479] Bluetooth: RFCOMM ver 1.11
[ 84.190980] input: 00:22:37:0B:3B:AF as /devices/virtual/input/input12
[ 275.087283] ata1.00: configured for UDMA/133
[ 275.087288] ata1: EH complete
[ 275.091331] ata2.00: configured for UDMA/133
[ 275.091346] ata2: EH complete
[ 275.095390] ata3.00: configured for UDMA/100
[ 275.095395] ata3: EH complete
[ 714.840411] perf interrupt took too long (2501 > 2500), lowering
kernel.perf_event_max_sample_rate to 50000
[ 3774.574528] show_signal_msg: 156 callbacks suppressed
[ 3774.574534] polari[821]: segfault at 0 ip 00007f86599eced2 sp
00007ffe091557e0 error 4 in libgjs.so.0.0.0[7f86599ba000+88000]
[ 6036.453857] usb 2-2.3: USB disconnect, device number 5
[ 6037.615546] usb 2-2.3: new high-speed USB device number 11 using xhci_hcd
[ 6037.718847] usb 2-2.3: New USB device found, idVendor=1b80, idProduct=d3a8
[ 6037.718853] usb 2-2.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 6037.718855] usb 2-2.3: Product: Rtl2832UDVB
[ 6037.718857] usb 2-2.3: Manufacturer: Realtek
** Model information
sys_vendor: HP
product_name: ProLiant ML110 G6
product_version:
chassis_vendor: HP
chassis_version: N/A
bios_vendor: HP
bios_version: O27
board_vendor: Wistron Corporation
board_name: ProLiant ML110 G6
board_version:
** Loaded modules:
uinput(E)
rfcomm(E)
xt_CHECKSUM(E)
iptable_mangle(E)
ipt_MASQUERADE(E)
nf_nat_masquerade_ipv4(E)
iptable_nat(E)
nf_nat_ipv4(E)
nf_nat(E)
nf_conntrack_ipv4(E)
nf_defrag_ipv4(E)
xt_conntrack(E)
nf_conntrack(E)
ipt_REJECT(E)
nf_reject_ipv4(E)
xt_tcpudp(E)
tun(E)
bridge(E)
stp(E)
llc(E)
ebtable_filter(E)
ebtables(E)
ip6table_filter(E)
ip6_tables(E)
iptable_filter(E)
ip_tables(E)
x_tables(E)
nfsd(E)
auth_rpcgss(E)
nfs_acl(E)
lockd(E)
grace(E)
sunrpc(E)
cpufreq_conservative(E)
cpufreq_userspace(E)
cpufreq_powersave(E)
cpufreq_stats(E)
bnep(E)
binfmt_misc(E)
quota_v2(E)
quota_tree(E)
iTCO_wdt(E)
iTCO_vendor_support(E)
joydev(E)
snd_usb_audio(E)
snd_usbmidi_lib(E)
snd_hwdep(E)
snd_rawmidi(E)
snd_seq_device(E)
snd_pcm(E)
usblp(E)
snd_timer(E)
snd(E)
soundcore(E)
btusb(E)
btrtl(E)
btbcm(E)
btintel(E)
bluetooth(E)
rfkill(E)
evdev(E)
kvm_intel(E)
kvm(E)
irqbypass(E)
pcspkr(E)
sg(E)
i2c_i801(E)
lpc_ich(E)
mfd_core(E)
8250_fintek(E)
shpchp(E)
button(E)
acpi_cpufreq(E)
tpm_tis(E)
tpm(E)
processor(E)
dm_mod(E)
cuse(E)
fuse(E)
coretemp(E)
loop(E)
ipmi_watchdog(E)
ipmi_si(E)
ipmi_poweroff(E)
ipmi_devintf(E)
ipmi_msghandler(E)
parport_pc(E)
ppdev(E)
lp(E)
parport(E)
autofs4(E)
ext4(E)
crc16(E)
mbcache(E)
jbd2(E)
btrfs(E)
crc32c_generic(E)
xor(E)
raid6_pq(E)
uhci_hcd(E)
sr_mod(E)
cdrom(E)
sd_mod(E)
hid_generic(E)
usbhid(E)
hid(E)
uas(E)
usb_storage(E)
radeon(E)
ahci(E)
i2c_algo_bit(E)
libahci(E)
xhci_pci(E)
drm_kms_helper(E)
tg3(E)
ehci_pci(E)
libata(E)
xhci_hcd(E)
ptp(E)
ehci_hcd(E)
pps_core(E)
ttm(E)
scsi_mod(E)
libphy(E)
crc32c_intel(E)
usbcore(E)
usb_common(E)
drm(E)
fjes(E)
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Core Processor DMI [8086:d130]
(rev 11)
Subsystem: Hewlett-Packard Company Core Processor DMI [103c:3318]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:03.0 PCI bridge [0604]: Intel Corporation Core Processor PCI Express Root
Port 1 [8086:d138] (rev 11) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: d1900000-d19fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:08.0 System peripheral [0880]: Intel Corporation Core Processor System
Management Registers [8086:d155] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:08.1 System peripheral [0880]: Intel Corporation Core Processor Semaphore
and Scratchpad Registers [8086:d156] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:08.2 System peripheral [0880]: Intel Corporation Core Processor System
Control and Status Registers [8086:d157] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:08.3 System peripheral [0880]: Intel Corporation Core Processor
Miscellaneous Registers [8086:d158] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:10.0 System peripheral [0880]: Intel Corporation Core Processor QPI Link
[8086:d150] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:10.1 System peripheral [0880]: Intel Corporation Core Processor QPI Routing
and Protocol Registers [8086:d151] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:1a.0 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset
USB2 Enhanced Host Controller [8086:3b3c] (rev 05) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company 5 Series/3400 Series Chipset USB2
Enhanced Host Controller [103c:3118]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d1e02000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1c.0 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI
Express Root Port 1 [8086:3b42] (rev 05) (prog-if 00 [Normal decode])
Physical Slot: 1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Bus: primary=00, secondary=10, subordinate=10, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: d1b00000-d1bfffff
Prefetchable memory behind bridge: 00000000d1c00000-00000000d1dfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.1 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI
Express Root Port 2 [8086:3b44] (rev 05) (prog-if 00 [Normal decode])
Physical Slot: 1
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 16
Bus: primary=00, secondary=1a, subordinate=1a, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: d1f00000-d20fffff
Prefetchable memory behind bridge: 00000000d2100000-00000000d22fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.2 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI
Express Root Port 3 [8086:3b46] (rev 05) (prog-if 00 [Normal decode])
Physical Slot: 1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 18
Bus: primary=00, secondary=1c, subordinate=1c, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: d1000000-d18fffff
Prefetchable memory behind bridge: 00000000d0000000-00000000d0ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.3 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI
Express Root Port 4 [8086:3b48] (rev 05) (prog-if 00 [Normal decode])
Physical Slot: 1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 19
Bus: primary=00, secondary=1e, subordinate=1e, sec-latency=0
I/O behind bridge: 00006000-00006fff
Memory behind bridge: d1a00000-d1afffff
Prefetchable memory behind bridge: 00000000d2300000-00000000d24fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.4 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI
Express Root Port 5 [8086:3b4a] (rev 05) (prog-if 00 [Normal decode])
Physical Slot: 1
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 17
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
I/O behind bridge: 00007000-00007fff
Memory behind bridge: d2500000-d26fffff
Prefetchable memory behind bridge: 00000000d2700000-00000000d28fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1d.0 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset
USB2 Enhanced Host Controller [8086:3b34] (rev 05) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company 5 Series/3400 Series Chipset USB2
Enhanced Host Controller [103c:3118]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d1e03000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
a5) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=30, subordinate=30, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 3400 Series Chipset LPC Interface
Controller [8086:3b14] (rev 05)
Subsystem: Hewlett-Packard Company 3420 Chipset LPC Interface
Controller [103c:3118]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
Kernel modules: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 5 Series/3400 Series Chipset
6 port SATA AHCI Controller [8086:3b22] (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: Hewlett-Packard Company 5 Series/3400 Series Chipset 6 port
SATA AHCI Controller [103c:3118]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 33
Region 0: I/O ports at 1830 [size=8]
Region 1: I/O ports at 1824 [size=4]
Region 2: I/O ports at 1828 [size=8]
Region 3: I/O ports at 1820 [size=4]
Region 4: I/O ports at 1800 [size=32]
Region 5: Memory at d1e04000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 5 Series/3400 Series Chipset SMBus
Controller [8086:3b30] (rev 05)
Subsystem: Hewlett-Packard Company 5 Series/3400 Series Chipset SMBus
Controller [103c:3318]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at d1e05000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc.
[AMD/ATI] RV516 GL [FireMV 2250] [1002:719b] (prog-if 00 [VGA controller])
Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] RV516 GL [FireMV
2250] [1002:0602]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at d1900000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at 2000 [size=256]
[virtual] Expansion ROM at d1920000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeon
Kernel modules: radeon
01:00.1 Display controller [0380]: Advanced Micro Devices, Inc. [AMD/ATI] RV516
GL [FireMV 2250] (Secondary) [1002:71bb]
Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] RV516 GL [FireMV
2250] (Secondary) [1002:0603]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Region 0: Memory at d1910000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
10:00.0 USB controller [0c03]: Renesas Technology Corp. uPD720202 USB 3.0 Host
Controller [1912:0015] (rev 02) (prog-if 30 [XHCI])
Subsystem: Renesas Technology Corp. uPD720202 USB 3.0 Host Controller
[1912:0015]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d1b00000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
1e:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5723
Gigabit Ethernet PCIe [14e4:165b] (rev 10)
Subsystem: Hewlett-Packard Company NC107i Integrated PCI Express
Gigabit Server Adapter [103c:705d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 34
Region 0: Memory at d1a00000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: tg3
Kernel modules: tg3
** USB devices:
Bus 004 Device 004: ID 0a5c:21e8 Broadcom Corp. BCM20702A0 Bluetooth 4.0
Bus 004 Device 003: ID 0000:0000
Bus 004 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 05e3:0612 Genesys Logic, Inc.
Bus 003 Device 004: ID 0bc2:3312 Seagate RSS LLC SRD00F2 Expansion Desktop
Drive (STBV)
Bus 003 Device 002: ID 05e3:0612 Genesys Logic, Inc.
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 011: ID 1b80:d3a8 Afatech
Bus 002 Device 010: ID 03f0:164a Hewlett-Packard
Bus 002 Device 009: ID 03f0:1198 Hewlett-Packard HID-compliant mouse
Bus 002 Device 008: ID 03f0:2824 Hewlett-Packard
Bus 002 Device 003: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
Bus 002 Device 002: ID 05e3:0612 Genesys Logic, Inc.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 005: ID 0b05:1743 ASUSTek Computer, Inc. Xonar U1 Audio Station
Bus 001 Device 004: ID 04e8:3268 Samsung Electronics Co., Ltd ML-1610 Mono
Laser Printer
Bus 001 Device 003: ID 04a9:1909 Canon, Inc. CanoScan LiDE 110
Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: stretch/sid
APT prefers testing
APT policy: (900, 'testing'), (300, 'unstable')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 4.5.0-1-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-4.5.0-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.59
ii initramfs-tools [linux-initramfs-tool] 0.125
ii kmod 22-1.1
ii linux-base 4.0
Versions of packages linux-image-4.5.0-1-amd64 recommends:
ii firmware-linux-free 3.4
ii irqbalance 1.1.0-2
Versions of packages linux-image-4.5.0-1-amd64 suggests:
ii debian-kernel-handbook 1.0.17
ii extlinux 3:6.03+dfsg-11
ii grub-pc 2.02~beta2-36
pn linux-doc-4.5 <none>
Versions of packages linux-image-4.5.0-1-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux 20160110-1
ii firmware-linux-nonfree 20160110-1
ii firmware-misc-nonfree [firmware-ralink] 20160110-1
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
ii firmware-realtek 20160110-1
pn xen-hypervisor <none>
-- debconf information:
linux-image-4.5.0-1-amd64/prerm/removing-running-kernel-4.5.0-1-amd64: true
--- End Message ---
