Package: src:linux
Version: 3.2.41-2
Severity: critical
Tags: moreinfo
My home server which has an old VIA EPIA-PD motherboard and C3
'Nehemiah' CPU has been unstable since I rebooted into this kernel
version. It will hard lock (no kernel log messages, no response to
magic SysRq) during heavy disk activity - initially a backup, but
then fsck also triggered it. My suspicion is that this may be related
to the 'longhaul' cpufreq driver which is now autoloaded and
previously wasn't. I will try running without it tomorrow. For now,
I've switched back to the squeeze kernel (2.6.32-48squeeze1) and have
completed the fsck and incremental backup without errors.
Following the first hard lockup, the BIOS failed to initialise RAM
(indicated by repeated beeps and no video output at power-on). I
have replaced the DIMM with a spare. (I then tested swapping back
to the original DIMM, and again it failed in the same way.) The
hard lockups continued with the replacement DIMM until I rebooted to
the squeeze kernel. So I have good reason to suspect that there is a
software cause for both the lockup and the hardware damage.
Marking this moreinfo because I need to check whether longhaul is the
culprit.
Ben.
-- Package-specific info:
** Kernel log
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-4-486 (debian-ker...@lists.debian.org) (gcc
version 4.6.3 (Debian 4.6.3-15) ) #1 Debian 3.2.41-2
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001eff0000 (usable)
[ 0.000000] BIOS-e820: 000000001eff0000 - 000000001eff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001eff3000 - 000000001f000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[ 0.000000] SMBIOS 2.2 present.
[ 0.000000] DMI: VIA Technologies, Inc. VT8623-8235/EPIA-PD, BIOS 6.00 PG
03/11/2004
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable)
==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0x1eff0 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CDFFF write-protect
[ 0.000000] CE000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask FE0000000 write-back
[ 0.000000] 1 base 01F000000 mask FFF000000 uncachable
[ 0.000000] 2 base 0E0000000 mask FFC000000 write-combining
[ 0.000000] 3 base 0E4000000 mask FFF800000 write-combining
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 01800000
[ 0.000000] Base memory trampoline at [c009c000] 9c000 size 12288
[ 0.000000] init_memory_mapping: 0000000000000000-000000001eff0000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 001ec00000 page 2M
[ 0.000000] 001ec00000 - 001eff0000 page 4k
[ 0.000000] kernel direct mapping tables up to 1eff0000 @ 17fa000-1800000
[ 0.000000] RAMDISK: 1db66000 - 1e5d7000
[ 0.000000] ACPI: RSDP 000f6480 00014 (v00 VT9174)
[ 0.000000] ACPI: RSDT 1eff3000 00028 (v01 VT9174 AWRDACPI 42302E31 AWRD
00000000)
[ 0.000000] ACPI: FACP 1eff3040 00074 (v01 VT9174 AWRDACPI 42302E31 AWRD
00000000)
[ 0.000000] ACPI: DSDT 1eff30c0 03462 (v01 VT9174 AWRDACPI 00001000 MSFT
0100000E)
[ 0.000000] ACPI: FACS 1eff0000 00040
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 495MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 1eff0000
[ 0.000000] low ram: 0 - 1eff0000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x0001eff0
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x000000a0
[ 0.000000] 0: 0x00000100 -> 0x0001eff0
[ 0.000000] On node 0 totalpages: 126848
[ 0.000000] free_area_init_node: node 0, pgdat c13c5938, node_mem_map
dec0f200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3952 pages, LIFO batch:0
[ 0.000000] Normal zone: 960 pages used for memmap
[ 0.000000] Normal zone: 121904 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] No local APIC present or hardware disabled
[ 0.000000] APIC: disable apic facility
[ 0.000000] APIC: switched to apic NOOP
[ 0.000000] nr_irqs_gsi: 16
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 1f000000 (gap:
1f000000:e0ff0000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 125856
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-486
root=UUID=08a2300d-648b-49de-a21a-34775bd30658 ro
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
[ 0.000000] Memory: 487400k/507840k available (2590k kernel code, 19992k
reserved, 1299k data, 452k init, 0k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfffa1000 - 0xfffff000 ( 376 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xdf7f0000 - 0xff7fe000 ( 512 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdeff0000 ( 495 MB)
[ 0.000000] .init : 0xc13cd000 - 0xc143e000 ( 452 kB)
[ 0.000000] .data : 0xc12878ec - 0xc13cc580 (1299 kB)
[ 0.000000] .text : 0xc1000000 - 0xc12878ec (2590 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor
mode...Ok.
[ 0.000000] NR_IRQS:2304 nr_irqs:256 16
[ 0.000000] CPU 0 irqstacks, hard=dd406000 soft=dd408000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1002.282 MHz processor.
[ 0.008006] Calibrating delay loop (skipped), value calculated using timer
frequency.. 2004.56 BogoMIPS (lpj=4009128)
[ 0.008115] pid_max: default: 32768 minimum: 301
[ 0.008280] Security Framework initialized
[ 0.008345] AppArmor: AppArmor disabled by boot time parameter
[ 0.008431] Mount-cache hash table entries: 512
[ 0.008765] Initializing cgroup subsys cpuacct
[ 0.008828] Initializing cgroup subsys memory
[ 0.008894] Initializing cgroup subsys devices
[ 0.008947] Initializing cgroup subsys freezer
[ 0.009000] Initializing cgroup subsys net_cls
[ 0.009053] Initializing cgroup subsys blkio
[ 0.009116] Initializing cgroup subsys perf_event
[ 0.009258] CPU: Centaur VIA Nehemiah stepping 08
[ 0.010316] ACPI: Core revision 20110623
[ 0.016528] ACPI: setting ELCR to 0200 (from 1e20)
[ 0.020173] Performance Events:
[ 0.020952] NMI watchdog disabled (cpu0): hardware events not enabled
[ 0.024446] devtmpfs: initialized
[ 0.024924] PM: Registering ACPI NVS region at 1eff0000 (12288 bytes)
[ 0.025529] print_constraints: dummy:
[ 0.025735] NET: Registered protocol family 16
[ 0.026098] EISA bus registered
[ 0.026262] ACPI: bus type pci registered
[ 0.032524] PCI: PCI BIOS revision 2.10 entry at 0xfad30, last bus=1
[ 0.032582] PCI: Using configuration type 1 for base access
[ 0.035242] bio: create slab <bio-0> at 0
[ 0.035527] ACPI: Added _OSI(Module Device)
[ 0.035582] ACPI: Added _OSI(Processor Device)
[ 0.035636] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.035689] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.037398] ACPI: EC: Look up EC in DSDT
[ 0.045850] ACPI: Interpreter enabled
[ 0.045937] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.046205] ACPI: Using PIC for interrupt routing
[ 0.055446] ACPI: No dock devices found.
[ 0.055515] HEST: Table not found.
[ 0.055574] PCI: Ignoring host bridge windows from ACPI; if necessary, use
"pci=use_crs" and report a bug
[ 0.055847] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.056388] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7]
(ignored)
[ 0.056403] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff]
(ignored)
[ 0.056416] pci_root PNP0A03:00: host bridge window [mem
0x000a0000-0x000bffff] (ignored)
[ 0.056429] pci_root PNP0A03:00: host bridge window [mem
0x000c0000-0x000dffff] (ignored)
[ 0.056443] pci_root PNP0A03:00: host bridge window [mem
0x1f000000-0xffefffff] (ignored)
[ 0.056489] pci 0000:00:00.0: [1106:3123] type 0 class 0x000600
[ 0.056514] pci 0000:00:00.0: reg 10: [mem 0xe0000000-0xe3ffffff pref]
[ 0.056633] pci 0000:00:01.0: [1106:b091] type 1 class 0x000604
[ 0.056700] pci 0000:00:01.0: supports D1
[ 0.056755] pci 0000:00:0f.0: [1106:3106] type 0 class 0x000200
[ 0.056784] pci 0000:00:0f.0: reg 10: [io 0xd000-0xd0ff]
[ 0.056805] pci 0000:00:0f.0: reg 14: [mem 0xeb040000-0xeb0400ff]
[ 0.056888] pci 0000:00:0f.0: supports D1 D2
[ 0.056899] pci 0000:00:0f.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.056942] pci 0000:00:10.0: [1106:3038] type 0 class 0x000c03
[ 0.057004] pci 0000:00:10.0: reg 20: [io 0xd400-0xd41f]
[ 0.057059] pci 0000:00:10.0: supports D1 D2
[ 0.057069] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.057111] pci 0000:00:10.1: [1106:3038] type 0 class 0x000c03
[ 0.057172] pci 0000:00:10.1: reg 20: [io 0xd800-0xd81f]
[ 0.057227] pci 0000:00:10.1: supports D1 D2
[ 0.057237] pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.057280] pci 0000:00:10.2: [1106:3038] type 0 class 0x000c03
[ 0.057341] pci 0000:00:10.2: reg 20: [io 0xdc00-0xdc1f]
[ 0.057396] pci 0000:00:10.2: supports D1 D2
[ 0.057406] pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.057447] pci 0000:00:10.3: [1106:3104] type 0 class 0x000c03
[ 0.057476] pci 0000:00:10.3: reg 10: [mem 0xeb041000-0xeb0410ff]
[ 0.057564] pci 0000:00:10.3: supports D1 D2
[ 0.057574] pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.057623] pci 0000:00:11.0: [1106:3177] type 0 class 0x000601
[ 0.057702] HPET not enabled in BIOS. You might try hpet=force boot option
[ 0.057775] pci 0000:00:11.0: quirk: [io 0x0400-0x047f] claimed by vt8235 PM
[ 0.057838] pci 0000:00:11.0: quirk: [io 0x0500-0x050f] claimed by vt8235
SMB
[ 0.057961] pci 0000:00:11.1: [1106:0571] type 0 class 0x000101
[ 0.058025] pci 0000:00:11.1: reg 20: [io 0xe000-0xe00f]
[ 0.058118] pci 0000:00:11.5: [1106:3059] type 0 class 0x000401
[ 0.058147] pci 0000:00:11.5: reg 10: [io 0xe400-0xe4ff]
[ 0.058238] pci 0000:00:11.5: supports D1 D2
[ 0.058279] pci 0000:00:12.0: [1106:3065] type 0 class 0x000200
[ 0.058308] pci 0000:00:12.0: reg 10: [io 0xe800-0xe8ff]
[ 0.058328] pci 0000:00:12.0: reg 14: [mem 0xeb042000-0xeb0420ff]
[ 0.058410] pci 0000:00:12.0: supports D1 D2
[ 0.058420] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.058467] pci 0000:00:14.0: [8086:107c] type 0 class 0x000200
[ 0.058499] pci 0000:00:14.0: reg 10: [mem 0xeb020000-0xeb03ffff]
[ 0.058520] pci 0000:00:14.0: reg 14: [mem 0xeb000000-0xeb01ffff]
[ 0.058540] pci 0000:00:14.0: reg 18: [io 0xec00-0xec3f]
[ 0.058586] pci 0000:00:14.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.058637] pci 0000:00:14.0: PME# supported from D0 D3hot D3cold
[ 0.058726] pci 0000:01:00.0: [1106:3122] type 0 class 0x000300
[ 0.058754] pci 0000:01:00.0: reg 10: [mem 0xe4000000-0xe7ffffff pref]
[ 0.058773] pci 0000:01:00.0: reg 14: [mem 0xe8000000-0xe8ffffff]
[ 0.058818] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
[ 0.058858] pci 0000:01:00.0: supports D1 D2
[ 0.058908] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.058970] pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe9ffffff]
[ 0.058986] pci 0000:00:01.0: bridge window [mem 0xe4000000-0xe7ffffff
pref]
[ 0.059004] pci_bus 0000:00: on NUMA node 0
[ 0.059020] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.059440] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
[ 0.059679] pci0000:00: Unable to request _OSC control (_OSC support mask:
0x1e)
[ 0.094431] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14
15)
[ 0.095165] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14
15)
[ 0.095895] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 10 11 12 14
15)
[ 0.096649] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 *12 14
15)
[ 0.097449] vgaarb: device added:
PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.097522] vgaarb: loaded
[ 0.097569] vgaarb: bridge control possible 0000:01:00.0
[ 0.097800] PCI: Using ACPI for IRQ routing
[ 0.097857] PCI: pci_cache_line_size set to 32 bytes
[ 0.097972] reserve RAM buffer: 000000001eff0000 - 000000001fffffff
[ 0.098382] Switching to clocksource pit
[ 0.101088] pnp: PnP ACPI init
[ 0.101216] ACPI: bus type pnp registered
[ 0.101890] pnp 00:00: [mem 0x000d1000-0x000d3fff]
[ 0.101903] pnp 00:00: [mem 0x000f0000-0x000f7fff]
[ 0.101914] pnp 00:00: [mem 0x000f8000-0x000fbfff]
[ 0.101925] pnp 00:00: [mem 0x000fc000-0x000fffff]
[ 0.101936] pnp 00:00: [mem 0x1eff0000-0x1effffff]
[ 0.101948] pnp 00:00: [mem 0xffff0000-0xffffffff]
[ 0.101958] pnp 00:00: [mem 0x00000000-0x0009ffff]
[ 0.101970] pnp 00:00: [mem 0x00100000-0x1efeffff]
[ 0.101981] pnp 00:00: [mem 0xfee00000-0xfee00fff]
[ 0.101992] pnp 00:00: [mem 0xfff80000-0xfffeffff]
[ 0.102219] system 00:00: [mem 0x000d1000-0x000d3fff] has been reserved
[ 0.102288] system 00:00: [mem 0x000f0000-0x000f7fff] could not be reserved
[ 0.102351] system 00:00: [mem 0x000f8000-0x000fbfff] could not be reserved
[ 0.102414] system 00:00: [mem 0x000fc000-0x000fffff] could not be reserved
[ 0.102477] system 00:00: [mem 0x1eff0000-0x1effffff] could not be reserved
[ 0.102541] system 00:00: [mem 0xffff0000-0xffffffff] has been reserved
[ 0.102603] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.102666] system 00:00: [mem 0x00100000-0x1efeffff] could not be reserved
[ 0.102729] system 00:00: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.102792] system 00:00: [mem 0xfff80000-0xfffeffff] has been reserved
[ 0.102856] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.103058] pnp 00:01: [bus 00-ff]
[ 0.103075] pnp 00:01: [io 0x0cf8-0x0cff]
[ 0.103086] pnp 00:01: [io 0x0000-0x0cf7 window]
[ 0.103097] pnp 00:01: [io 0x0d00-0xffff window]
[ 0.103108] pnp 00:01: [mem 0x000a0000-0x000bffff window]
[ 0.103120] pnp 00:01: [mem 0x000c0000-0x000dffff window]
[ 0.103132] pnp 00:01: [mem 0x1f000000-0xffefffff window]
[ 0.103284] pnp 00:01: Plug and Play ACPI device, IDs PNP0a03 (active)
[ 0.103358] pnp 00:02: [io 0x0400-0x047f]
[ 0.103369] pnp 00:02: [io 0x0500-0x050f]
[ 0.103511] system 00:02: [io 0x0400-0x047f] has been reserved
[ 0.103575] system 00:02: [io 0x0500-0x050f] has been reserved
[ 0.103635] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.104034] pnp 00:03: [io 0x0010-0x001f]
[ 0.104045] pnp 00:03: [io 0x0022-0x003f]
[ 0.104055] pnp 00:03: [io 0x0044-0x005f]
[ 0.104065] pnp 00:03: [io 0x0062-0x0063]
[ 0.104075] pnp 00:03: [io 0x0065-0x006f]
[ 0.104085] pnp 00:03: [io 0x0074-0x007f]
[ 0.104095] pnp 00:03: [io 0x0091-0x0093]
[ 0.104105] pnp 00:03: [io 0x00a2-0x00bf]
[ 0.104115] pnp 00:03: [io 0x00e0-0x00ef]
[ 0.104125] pnp 00:03: [io 0x04d0-0x04d1]
[ 0.104298] system 00:03: [io 0x04d0-0x04d1] has been reserved
[ 0.104360] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.104406] pnp 00:04: [dma 4]
[ 0.104416] pnp 00:04: [io 0x0000-0x000f]
[ 0.104426] pnp 00:04: [io 0x0080-0x0090]
[ 0.104436] pnp 00:04: [io 0x0094-0x009f]
[ 0.104446] pnp 00:04: [io 0x00c0-0x00df]
[ 0.104556] pnp 00:04: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.104601] pnp 00:05: [io 0x0070-0x0073]
[ 0.104614] pnp 00:05: [irq 8]
[ 0.104731] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.104765] pnp 00:06: [io 0x0061]
[ 0.104876] pnp 00:06: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.104911] pnp 00:07: [io 0x00f0-0x00ff]
[ 0.104922] pnp 00:07: [irq 13]
[ 0.105041] pnp 00:07: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.105490] pnp 00:08: [io 0x03f8-0x03ff]
[ 0.105502] pnp 00:08: [irq 4]
[ 0.105845] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.106514] pnp 00:09: [io 0x0378-0x037f]
[ 0.106525] pnp 00:09: [irq 7]
[ 0.106732] pnp 00:09: Plug and Play ACPI device, IDs PNP0400 (active)
[ 0.107073] pnp 00:0a: [io 0x0060]
[ 0.107083] pnp 00:0a: [io 0x0064]
[ 0.107258] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.107744] pnp: PnP ACPI: found 11 devices
[ 0.107803] ACPI: ACPI bus type pnp unregistered
[ 0.107861] PnPBIOS: Disabled by ACPI PNP
[ 0.149744] Switching to clocksource acpi_pm
[ 0.149859] PCI: max bus depth: 1 pci_try_num: 2
[ 0.149937] pci 0000:00:14.0: BAR 6: assigned [mem 0x20000000-0x2001ffff
pref]
[ 0.150013] pci 0000:01:00.0: BAR 6: assigned [mem 0xe9000000-0xe900ffff
pref]
[ 0.150083] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.150147] pci 0000:00:01.0: bridge window [mem 0xe8000000-0xe9ffffff]
[ 0.150210] pci 0000:00:01.0: bridge window [mem 0xe4000000-0xe7ffffff
pref]
[ 0.150301] pci 0000:00:01.0: setting latency timer to 64
[ 0.150315] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.150327] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[ 0.150341] pci_bus 0000:01: resource 1 [mem 0xe8000000-0xe9ffffff]
[ 0.150354] pci_bus 0000:01: resource 2 [mem 0xe4000000-0xe7ffffff pref]
[ 0.150534] NET: Registered protocol family 2
[ 0.150786] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.151526] TCP established hash table entries: 16384 (order: 5, 131072
bytes)
[ 0.152068] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.152416] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.152474] TCP reno registered
[ 0.152528] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.152603] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.152952] NET: Registered protocol family 1
[ 0.153050] pci 0000:00:01.0: disabling DAC on VIA PCI bridge
[ 0.154132] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
[ 0.154193] PCI: setting IRQ 10 as level-triggered
[ 0.154963] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[ 0.155020] PCI: setting IRQ 11 as level-triggered
[ 0.155626] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
[ 0.155682] PCI: setting IRQ 5 as level-triggered
[ 0.156529] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 12
[ 0.156587] PCI: setting IRQ 12 as level-triggered
[ 0.156682] pci 0000:01:00.0: Boot video device
[ 0.156694] PCI: CLS 32 bytes, default 32
[ 0.156900] Unpacking initramfs...
[ 1.481804] Freeing initrd memory: 10692k freed
[ 1.540951] audit: initializing netlink socket (disabled)
[ 1.541043] type=2000 audit(1367895988.537:1): initialized
[ 1.601016] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.601440] VFS: Disk quotas dquot_6.5.2
[ 1.601563] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.601793] msgmni has been set to 972
[ 1.602365] alg: No test for stdrng (krng)
[ 1.602516] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
253)
[ 1.602586] io scheduler noop registered
[ 1.602637] io scheduler deadline registered
[ 1.602707] io scheduler cfq registered (default)
[ 1.603135] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.603267] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.603325] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 1.604544] ERST: Table is not found!
[ 1.604599] GHES: HEST is not enabled!
[ 1.604692] isapnp: Scanning for PnP cards...
[ 1.958553] isapnp: No Plug & Play device found
[ 1.958842] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.979309] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.000655] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.001427] Linux agpgart interface v0.103
[ 2.001930] agpgart: Detected VIA CLE266 chipset
[ 2.009594] agpgart-via 0000:00:00.0: AGP aperture is 64M @ 0xe0000000
[ 2.010037] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 2.260142] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.260574] mousedev: PS/2 mouse device common for all mice
[ 2.260774] rtc_cmos 00:05: RTC can wake from S4
[ 2.261098] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 2.261188] rtc0: alarms up to one year, y3k, 242 bytes nvram
[ 2.261440] EISA: Probing bus 0 at eisa.0
[ 2.261555] EISA: Detected 0 cards.
[ 2.261607] cpuidle: using governor ladder
[ 2.261659] cpuidle: using governor menu
[ 2.262595] TCP cubic registered
[ 2.262713] NET: Registered protocol family 10
[ 2.264611] Mobile IPv6
[ 2.264668] NET: Registered protocol family 17
[ 2.264728] Registering the dns_resolver key type
[ 2.264821] Using IPI Shortcut mode
[ 2.265282] PM: Hibernation image not present or could not be loaded.
[ 2.265316] registered taskstats version 1
[ 2.265996] rtc_cmos 00:05: setting system clock to 2013-05-07 03:06:29 UTC
(1367895989)
[ 2.266198] Initializing network drop monitor service
[ 2.266639] Freeing unused kernel memory: 452k freed
[ 2.269023] Write protecting the kernel text: 2592k
[ 2.269170] Write protecting the kernel read-only data: 1040k
[ 2.312609] udevd[42]: starting version 175
[ 2.442798] via_rhine: v1.10-LK1.5.0 2010-10-09 Written by Donald Becker
[ 2.442877] via_rhine: Broken BIOS detected, avoid_D3 enabled
[ 2.591368] via-rhine 0000:00:0f.0: eth0: VIA Rhine III at 0x1d000,
00:40:63:dd:e1:20, IRQ 12
[ 2.592214] via-rhine 0000:00:0f.0: eth0: MII PHY found at address 1, status
0x7869 advertising 05e1 Link 41e1
[ 2.596214] Refined TSC clocksource calibration: 1002.272 MHz.
[ 2.596293] Switching to clocksource tsc
[ 2.691083] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[ 2.691156] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 2.724163] via-rhine 0000:00:12.0: eth1: VIA Rhine II at 0x1e800,
00:40:63:dd:e1:70, IRQ 10
[ 2.724958] via-rhine 0000:00:12.0: eth1: MII PHY found at address 1, status
0x7869 advertising 05e1 Link 45e1
[ 2.729100] usbcore: registered new interface driver usbfs
[ 2.729251] usbcore: registered new interface driver hub
[ 2.743091] usbcore: registered new device driver usb
[ 2.754306] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.767531] uhci_hcd: USB Universal Host Controller Interface driver
[ 3.038021] SCSI subsystem initialized
[ 3.180760] libata version 3.00 loaded.
[ 3.384406] e1000 0000:00:14.0: eth2: (PCI:33MHz:32-bit) 00:1b:21:1e:e3:68
[ 3.384483] e1000 0000:00:14.0: eth2: Intel(R) PRO/1000 Network Connection
[ 3.384675] ehci_hcd 0000:00:10.3: EHCI Host Controller
[ 3.384789] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus
number 1
[ 3.384952] ehci_hcd 0000:00:10.3: irq 12, io mem 0xeb041000
[ 3.396087] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00
[ 3.396237] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.396299] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.396367] usb usb1: Product: EHCI Host Controller
[ 3.396421] usb usb1: Manufacturer: Linux 3.2.0-4-486 ehci_hcd
[ 3.396477] usb usb1: SerialNumber: 0000:00:10.3
[ 3.397053] hub 1-0:1.0: USB hub found
[ 3.397116] hub 1-0:1.0: 6 ports detected
[ 3.397467] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 3.397563] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus
number 2
[ 3.397681] uhci_hcd 0000:00:10.0: irq 10, io base 0x0000d400
[ 3.397906] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.397967] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.398034] usb usb2: Product: UHCI Host Controller
[ 3.398088] usb usb2: Manufacturer: Linux 3.2.0-4-486 uhci_hcd
[ 3.398144] usb usb2: SerialNumber: 0000:00:10.0
[ 3.399114] hub 2-0:1.0: USB hub found
[ 3.399188] hub 2-0:1.0: 2 ports detected
[ 3.399500] pata_via 0000:00:11.1: version 0.3.4
[ 3.399540] pata_via 0000:00:11.1: VIA VLink IRQ fixup, from 255 to 10
[ 3.408138] scsi0 : pata_via
[ 3.408946] scsi1 : pata_via
[ 3.418220] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xe000 irq 14
[ 3.418295] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xe008 irq 15
[ 3.418572] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 3.418673] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus
number 3
[ 3.418789] uhci_hcd 0000:00:10.1: irq 11, io base 0x0000d800
[ 3.419032] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.419094] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.419161] usb usb3: Product: UHCI Host Controller
[ 3.419215] usb usb3: Manufacturer: Linux 3.2.0-4-486 uhci_hcd
[ 3.419271] usb usb3: SerialNumber: 0000:00:10.1
[ 3.421849] hub 3-0:1.0: USB hub found
[ 3.421936] hub 3-0:1.0: 2 ports detected
[ 3.422272] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 3.422356] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus
number 4
[ 3.422471] uhci_hcd 0000:00:10.2: irq 5, io base 0x0000dc00
[ 3.422696] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.422758] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.422825] usb usb4: Product: UHCI Host Controller
[ 3.422880] usb usb4: Manufacturer: Linux 3.2.0-4-486 uhci_hcd
[ 3.422936] usb usb4: SerialNumber: 0000:00:10.2
[ 3.429267] hub 4-0:1.0: USB hub found
[ 3.429355] hub 4-0:1.0: 2 ports detected
[ 3.609742] ata1.00: ATA-6: WDC WD1600JB-00GVA0, 08.02D08, max UDMA/100
[ 3.609816] ata1.00: 312581808 sectors, multi 16: LBA48
[ 3.611248] ata1.01: ATA-6: WDC WD1600JB-00GVA0, 08.02D08, max UDMA/100
[ 3.611310] ata1.01: 312581808 sectors, multi 16: LBA48
[ 3.625574] ata1.00: configured for UDMA/100
[ 3.641594] ata1.01: configured for UDMA/100
[ 3.642027] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JB-00G 08.0
PQ: 0 ANSI: 5
[ 3.643470] scsi 0:0:1:0: Direct-Access ATA WDC WD1600JB-00G 08.0
PQ: 0 ANSI: 5
[ 3.816419] ata2.00: ATAPI: MATSHITADVD-ROM SR-8587, 5X37, max UDMA/33
[ 3.816505] ata2.01: ATAPI: SAMSUNG CD-R/RW SW-216B Q001 20010913, Q001,
max MWDMA2
[ 3.824283] ata2.00: configured for UDMA/33
[ 3.840271] ata2.01: configured for MWDMA2
[ 3.841737] scsi 1:0:0:0: CD-ROM MATSHITA DVD-ROM SR-8587 5X37
PQ: 0 ANSI: 5
[ 3.844873] scsi 1:0:1:0: CD-ROM SAMSUNG CD-R/RW SW-216B Q001
PQ: 0 ANSI: 5
[ 3.912913] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149
GiB)
[ 3.913145] sd 0:0:0:0: [sda] Write Protect is off
[ 3.913205] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.913277] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 3.915253] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 3.915330] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 3.917519] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 3.920222] sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
[ 3.922000] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 3.934136] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.934477] sd 0:0:1:0: Attached scsi generic sg1 type 0
[ 3.940524] sr 1:0:0:0: Attached scsi generic sg2 type 5
[ 3.940919] sr 1:0:1:0: Attached scsi generic sg3 type 5
[ 3.941781] sd 0:0:1:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149
GiB)
[ 3.947751] sda: sda1 sda2 < sda5 sda6 >
[ 3.948009] sd 0:0:1:0: [sdb] Write Protect is off
[ 3.948117] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 3.948363] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 3.967243] sdb: sdb1
[ 3.967644] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.968482] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 4.531318] device-mapper: uevent: version 1.0.3
[ 4.533149] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised:
dm-de...@redhat.com
[ 4.552985] PM: Starting manual resume from disk
[ 4.553067] PM: Hibernation image partition 8:5 present
[ 4.553076] PM: Looking for hibernation image.
[ 4.553556] PM: Image not found (code -22)
[ 4.553566] PM: Hibernation image not present or could not be loaded.
[ 4.606906] kjournald starting. Commit interval 5 seconds
[ 4.607006] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 6.546791] udevd[309]: starting version 175
[ 6.970390] Marking TSC unstable due to TSC halts in idle
[ 6.970495] ACPI: acpi_idle registered with cpuidle
[ 6.972179] input: Power Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 6.972279] ACPI: Power Button [PWRB]
[ 6.973895] Switching to clocksource acpi_pm
[ 6.984697] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 6.984789] ACPI: Power Button [PWRF]
[ 7.052636] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 7.125982] parport_pc 00:09: reported by Plug and Play ACPI
[ 7.126081] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
[ 7.234717] udevd[333]: renamed network interface eth0 to ext0
[ 7.313680] udevd[347]: renamed network interface eth1 to wl1
[ 7.350805] udevd[335]: renamed network interface eth2 to int0
[ 7.392123] NET: Registered protocol family 23
[ 7.554996] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 7.585156] longhaul: VIA C3 'Nehemiah C' [C5P] CPU detected. Powersaver
supported.
[ 7.585293] longhaul: ACPI I/O at 0x400
[ 7.585367] longhaul: Using northbridge support.
[ 7.585418] longhaul: Using ACPI support.
[ 7.698447] padlock_aes: Using VIA PadLock ACE for AES algorithm.
[ 7.889236] Error: Driver 'pcspkr' is already registered, aborting...
[ 8.142748] snd_via82xx 0000:00:11.5: setting latency timer to 64
[ 10.167000] Adding 3903756k swap on /dev/sda5. Priority:-1 extents:1
across:3903756k
[ 10.405752] EXT3-fs (sda1): using internal journal
[ 10.743695] vt1211: Found VT1211 chip at 0x6000, revision 2
[ 17.141128] kjournald starting. Commit interval 5 seconds
[ 17.141908] EXT3-fs (dm-3): warning: checktime reached, running e2fsck is
recommended
[ 17.142922] EXT3-fs (dm-3): using internal journal
[ 17.143003] EXT3-fs (dm-3): mounted filesystem with ordered data mode
[ 17.199883] kjournald starting. Commit interval 5 seconds
[ 17.200082] EXT3-fs (dm-0): warning: maximal mount count reached, running
e2fsck is recommended
[ 17.200752] EXT3-fs (dm-0): using internal journal
[ 17.200836] EXT3-fs (dm-0): mounted filesystem with ordered data mode
[ 17.274693] kjournald starting. Commit interval 5 seconds
[ 17.274832] EXT3-fs (dm-2): warning: maximal mount count reached, running
e2fsck is recommended
[ 17.275880] EXT3-fs (dm-2): using internal journal
[ 17.275965] EXT3-fs (dm-2): mounted filesystem with ordered data mode
[ 17.354808] kjournald starting. Commit interval 5 seconds
[ 17.355737] EXT3-fs (dm-1): using internal journal
[ 17.355822] EXT3-fs (dm-1): mounted filesystem with ordered data mode
[ 21.059583] ADDRCONF(NETDEV_UP): int0: link is not ready
[ 21.081821] e1000: int0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control:
RX/TX
[ 21.083997] ADDRCONF(NETDEV_CHANGE): int0: link becomes ready
[ 31.360064] int0: no IPv6 routers present
[ 32.052112] via-rhine 0000:00:12.0: wl1: link up, 100Mbps, full-duplex, lpa
0x45E1
[ 42.352107] wl1: no IPv6 routers present
[ 53.149728] via-rhine 0000:00:0f.0: ext0: link up, 100Mbps, full-duplex, lpa
0x41E1
[ 63.592055] ext0: no IPv6 routers present
[ 63.893001] PPP generic driver version 2.4.2
[ 64.046249] device ext0 entered promiscuous mode
[ 65.528688] PPP BSD Compression module registered
[ 65.543867] PPP Deflate Compression module registered
[ 74.611368] IPv6 over IPv4 tunneling driver
[ 86.583639] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 86.718812] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 86.878711] RPC: Registered named UNIX socket transport module.
[ 86.878736] RPC: Registered udp transport module.
[ 86.878751] RPC: Registered tcp transport module.
[ 86.878767] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 86.968534] FS-Cache: Loaded
[ 87.148151] FS-Cache: Netfs 'nfs' registered for caching
[ 87.224875] Installing knfsd (copyright (C) 1996 o...@monad.swb.de).
[ 87.317102] nf_conntrack version 0.5.0 (7789 buckets, 31156 max)
[ 89.071188] fuse init (API version 7.17)
** Model information
bios_date:03/11/2004
bios_vendor:Award Software International, Inc.
bios_version:6.00 PG
board_name:EPIA-PD
board_vendor:
board_version:
product_name:VT8623-8235
product_version:
sys_vendor:VIA Technologies, Inc.
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT8623 [Apollo CLE266]
[1106:3123]
Subsystem: VIA Technologies, Inc. Device [1106:aa01]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 8
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: <access denied>
Kernel driver in use: agpgart-via
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP]
[1106:b091] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+ INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: e8000000-e9ffffff
Prefetchable memory behind bridge: e4000000-e7ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:0f.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105/VT6106S
[Rhine-III] [1106:3106] (rev 8b)
Subsystem: VIA Technologies, Inc. Device [1106:0106]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at eb040000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: via-rhine
00:10.0 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller [1106:3038] (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. Device [1106:aa01]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at d400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:10.1 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller [1106:3038] (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. Device [1106:aa01]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at d800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:10.2 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller [1106:3038] (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. Device [1106:aa01]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 5
Region 4: I/O ports at dc00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:10.3 USB controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev
82) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0 [1106:3104]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 12
Region 0: Memory at eb041000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8235 ISA Bridge [1106:3177]
Subsystem: VIA Technologies, Inc. Device [1106:aa01]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:11.1 IDE interface [0101]: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06)
(prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Device [1106:aa01]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 10
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at e000 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_via
00:11.5 Multimedia audio controller [0401]: VIA Technologies, Inc.
VT8233/A/8235/8237 AC97 Audio Controller [1106:3059] (rev 50)
Subsystem: VIA Technologies, Inc. Device [1106:aa01]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at e400 [size=256]
Capabilities: <access denied>
Kernel driver in use: VIA 82xx Audio
00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II]
[1106:3065] (rev 74)
Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet
Controller on VT8235 [1106:0102]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e800 [size=256]
Region 1: Memory at eb042000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: via-rhine
00:14.0 Ethernet controller [0200]: Intel Corporation 82541PI Gigabit Ethernet
Controller [8086:107c] (rev 05)
Subsystem: Intel Corporation PRO/1000 GT Desktop Adapter [8086:1376]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (63750ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at eb020000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at eb000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at ec00 [size=64]
[virtual] Expansion ROM at 20000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: e1000
01:00.0 VGA compatible controller [0300]: VIA Technologies, Inc. VT8623 [Apollo
CLE266] integrated CastleRock graphics [1106:3122] (rev 03) (prog-if 00 [VGA
controller])
Subsystem: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated
CastleRock graphics [1106:3122]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at e8000000 (32-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at e9000000 [disabled] [size=64K]
Capabilities: <access denied>
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 006: ID 07ff:00ff Unknown Portable Hard Drive
-- System Information:
Debian Release: 7.0
APT prefers stable
APT policy: (990, 'stable'), (500, 'stable-updates'), (500, 'oldstable'),
(100, 'proposed-updates'), (100, 'unstable')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-5-486
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-3.2.0-4-486 depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.109.1
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.2.0-4-486 recommends:
ii firmware-linux-free 3.2
Versions of packages linux-image-3.2.0-4-486 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u1
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-486 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-486/postinst/missing-firmware-3.2.0-4-486:
linux-image-3.2.0-4-486/postinst/ignoring-ramdisk:
linux-image-3.2.0-4-486/prerm/removing-running-kernel-3.2.0-4-486: true
linux-image-3.2.0-4-486/postinst/depmod-error-initrd-3.2.0-4-486: false
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
