On 12/05/14 18:52, Andrew Shadura wrote: > Could you please post the output of ifup -a -v? That'd help a lot.
Sure thing. I did an "ip address flush eth0" before each of these so it was starting from 'reasonably clean'. Firstly, with the IPv4 stanza appearing before the IPv6 stanza: run-parts --exit-on-error --verbose /etc/network/if-pre-up.d run-parts: executing /etc/network/if-pre-up.d/bridge run-parts: executing /etc/network/if-pre-up.d/ethtool run-parts: executing /etc/network/if-pre-up.d/wpasupplicant Configuring interface eth0=eth0 (inet) run-parts --exit-on-error --verbose /etc/network/if-pre-up.d run-parts: executing /etc/network/if-pre-up.d/bridge run-parts: executing /etc/network/if-pre-up.d/ethtool run-parts: executing /etc/network/if-pre-up.d/wpasupplicant ip addr add 192.168.1.1/255.255.255.0 broadcast 192.168.1.255 dev eth0 label eth0 ip link set dev eth0 up ip route add default via 192.168.1.254 dev eth0 run-parts --exit-on-error --verbose /etc/network/if-up.d run-parts: executing /etc/network/if-up.d/avahi-daemon run-parts: /etc/network/if-up.d/avahi-daemon exited with return code 1 run-parts --exit-on-error --verbose /etc/network/if-up.d Failed to bring up eth0. run-parts: executing /etc/network/if-up.d/avahi-daemon run-parts: executing /etc/network/if-up.d/bind9 run-parts: executing /etc/network/if-up.d/ethtool run-parts: executing /etc/network/if-up.d/iptables run-parts: executing /etc/network/if-up.d/mountnfs run-parts: executing /etc/network/if-up.d/ntpdate run-parts: executing /etc/network/if-up.d/openssh-server run-parts: executing /etc/network/if-up.d/openvpn run-parts: executing /etc/network/if-up.d/upstart run-parts: executing /etc/network/if-up.d/wpasupplicant And secondly with the IPv6 stanza appearing before the IPv4 stanza: run-parts --exit-on-error --verbose /etc/network/if-pre-up.d run-parts: executing /etc/network/if-pre-up.d/bridge run-parts: executing /etc/network/if-pre-up.d/ethtool run-parts: executing /etc/network/if-pre-up.d/wpasupplicant Configuring interface eth0=eth0 (inet6) run-parts --exit-on-error --verbose /etc/network/if-pre-up.d run-parts: executing /etc/network/if-pre-up.d/bridge run-parts: executing /etc/network/if-pre-up.d/ethtool run-parts: executing /etc/network/if-pre-up.d/wpasupplicant modprobe -q net-pf-10 > /dev/null 2>&1 || true # ignore failure. sysctl -q -e -w net.ipv6.conf.eth0.autoconf=0 ip link set dev eth0 up ip -6 addr add 2001:8b0:9d7:6b00::1/64 dev eth0 ip -6 route add default via 2001:8b0:9d7:6b00:9e97:26ff:fe77:4cfa dev eth0 run-parts --exit-on-error --verbose /etc/network/if-up.d Failed to bring up eth0. run-parts: executing /etc/network/if-up.d/avahi-daemon run-parts: executing /etc/network/if-up.d/bind9 run-parts: executing /etc/network/if-up.d/ethtool run-parts: executing /etc/network/if-up.d/iptables run-parts: executing /etc/network/if-up.d/mountnfs run-parts: executing /etc/network/if-up.d/ntpdate run-parts: executing /etc/network/if-up.d/openssh-server run-parts: executing /etc/network/if-up.d/openvpn run-parts: executing /etc/network/if-up.d/upstart run-parts: executing /etc/network/if-up.d/wpasupplicant In each case only one address family is configured, whereas up until last week both address families were configured (with the IPv4 stanza appearing before the IPv6 stanza). I notice that there's a "Failed to bring up eth0" message in both cases - I don't know whether this is because the interface already existed at the time of running the scripts, or whether this is indicative of the problem. -- Andrew Benham Southgate, London N14, United Kingdom The gates in my computer are AND OR and NOT, not "Bill" -- To UNSUBSCRIBE, email to [email protected] with a subject of "unsubscribe". Trouble? Contact [email protected]
