Package: src:linux Version: 4.18.20-2 Severity: normal Dear Maintainer,
I tried Buster with 4.18.20-2 kernel on an Alix 2C2, with Geode LX800, BIOS 0.99m. After grub unpacking initramfs, the (serial) console outputs nothing (despite earlyprintk/boot_delay), then it reboots by itself. (Same with 4.18.10-1) Then I tried linux-image-4.18.0-0.bpo.1-686_4.18.6-1~bpo9+1_i386.deb, and that works mostly fine. With this kernel, printk starts at about the same time, as with the other kernel I would see the POST. (Stretch 4.9 kernel also works FWIW). For reference, I saw a Geode LX issue mentioned in this thread too: https://lists.debian.org/debian-kernel/2018/09/msg00295.html My issue is maybe different than that, because I get no output at all (no "not compatible with i586" message). And as the stretch-backports kernel does work, I thought it isn't due to (the mentioned in thread) upstream, but due to Debian's config. (Or was perhaps meant, upstream gcc?) >From the Debian kernel changelog I concluded, the problem from that thread >might have been fixed in 4.18.10-1. At least in there is a Geode fix. So, as mentioned, I also tried that kernel, but same problem. Note that the info below is while booted with the backports kernel (same commandline options etc). The info above (Subject/Version) I edited to match the nonbooting kernel. Thank you, Gert -- Package-specific info: ** Version: Linux version 4.18.0-0.bpo.1-686 ** Command line: BOOT_IMAGE=/boot/vmlinuz-4.18.0-0.bpo.1-686 root=UUID=423c6d29-ad6f-4de5-8612-b7dfcf8c9efd ro console=ttyS0,115200n8 earlyprintk=ttyS0,115200n8 apparmor=1 security=apparmor ipv6.disable=1 noisapnp slub_debug=P page_poison=1 slab_nomerge pti=on nomfgpt ** Not tainted ** Kernel log: Unable to read kernel log; any relevant messages should be attached ** Model information Alix 2C2 Geode LX800 BIOS 0.99m ** Loaded modules: evdev gpio_cs5535 scx200_acb cs5535_mfgpt ohci_pci ohci_hcd ehci_pci cbc ehci_hcd pcspkr sg geode_aes usbcore gpio_keys_polled via_rhine mii leds_gpio input_polldev cs5535_mfd usb_common geode_rng rng_core ip_tables x_tables autofs4 ext4 crc16 mbcache jbd2 crc32c_generic fscrypto ecb crypto_simd cryptd aes_i586 sd_mod ata_generic pata_cs5536 pata_amd libata scsi_mod ** Network interface configuration: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). source /etc/network/interfaces.d/* # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug enp0s9 iface enp0s9 inet dhcp ** Network status: *** IP interfaces and addresses: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever 2: enp0s9: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether 00:0d:b9:12:d0:f4 brd ff:ff:ff:ff:ff:ff inet 192.168.1.226/24 brd 192.168.1.255 scope global enp0s9 valid_lft forever preferred_lft forever 3: enp0s11: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether 00:0d:b9:12:d0:f5 brd ff:ff:ff:ff:ff:ff *** Device statistics: Inter-| Receive | Transmit face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed enp0s11: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 enp0s9: 59613 392 0 0 0 0 0 0 59482 343 0 0 0 0 0 0 lo: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ** PCI devices: 00:01.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] Host Bridge [1022:2080] (rev 31) Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] Host Bridge [1022:2080] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 248, Cache Line Size: 32 bytes Region 0: I/O ports at 0000 00:01.2 Entertainment encryption device [1010]: Advanced Micro Devices, Inc. [AMD] Geode LX AES Security Block [1022:2082] Subsystem: Advanced Micro Devices, Inc. [AMD] Geode LX AES Security Block [1022:2082] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 9 Region 0: Memory at efff4000 (32-bit, non-prefetchable) [size=16K] Kernel driver in use: Geode LX AES Kernel modules: geode_rng, geode_aes 00:09.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96) Subsystem: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:0106] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at 1000 [size=256] Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: via-rhine Kernel modules: via_rhine 00:0b.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96) Subsystem: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:0106] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 15 Region 0: I/O ports at 1400 [size=256] Region 1: Memory at e0040000 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: via-rhine Kernel modules: via_rhine 00:0f.0 ISA bridge [0601]: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] ISA [1022:2090] (rev 03) Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] ISA [1022:2090] Control: I/O+ Mem- BusMaster- SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Region 0: I/O ports at 6000 [size=8] Region 1: I/O ports at 6100 [size=256] Region 2: I/O ports at 6200 [size=64] Region 3: I/O ports at 0000 Region 4: I/O ports at 9d00 [size=128] Region 5: I/O ports at 9c00 [size=64] Kernel driver in use: cs5535-mfd Kernel modules: cs5535_mfd 00:0f.2 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] IDE [1022:209a] (rev 01) (prog-if 80 [ISA Compatibility mode-only controller, supports bus mastering]) Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] IDE [1022:209a] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 248, Cache Line Size: 32 bytes Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) Region 4: I/O ports at ff00 [size=16] Kernel driver in use: pata_amd Kernel modules: pata_amd, pata_cs5536, ata_generic 00:0f.4 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] OHC [1022:2094] (rev 02) (prog-if 10 [OHCI]) Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] OHC [1022:2094] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin D routed to IRQ 12 Region 0: Memory at efffe000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: ohci-pci Kernel modules: ohci_pci 00:0f.5 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] EHC [1022:2095] (rev 02) (prog-if 20 [EHCI]) Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] EHC [1022:2095] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin D routed to IRQ 12 Region 0: Memory at efffd000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: ehci-pci Kernel modules: ehci_pci ** USB devices: not available -- System Information: Debian Release: buster/sid APT prefers testing APT policy: (500, 'testing') Architecture: i386 (i586) Kernel: Linux 4.18.0-0.bpo.1-686 (SMP w/1 CPU core) Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968), LANGUAGE=C (charmap=ANSI_X3.4-1968) Shell: /bin/sh linked to /bin/dash Init: systemd (via /run/systemd/system) LSM: AppArmor: enabled Versions of packages linux-image-4.18.0-0.bpo.1-686 depends on: ii initramfs-tools [linux-initramfs-tool] 0.132 ii kmod 25-2 ii linux-base 4.5 Versions of packages linux-image-4.18.0-0.bpo.1-686 recommends: ii apparmor 2.13.1-3+b1 pn firmware-linux-free <none> pn irqbalance <none> Versions of packages linux-image-4.18.0-0.bpo.1-686 suggests: pn debian-kernel-handbook <none> ii grub-pc 2.02+dfsg1-8 pn linux-doc-4.18 <none> Versions of packages linux-image-4.18.0-0.bpo.1-686 is related to: pn firmware-amd-graphics <none> pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-cavium <none> pn firmware-intel-sound <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> pn firmware-linux-nonfree <none> pn firmware-misc-nonfree <none> pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-realtek <none> pn firmware-samsung <none> pn firmware-siano <none> pn firmware-ti-connectivity <none> pn xen-hypervisor <none> -- no debconf information *** /tmp/dmesg-4.18.0-0.bpo.1-686 [ 0.000000] Linux version 4.18.0-0.bpo.1-686 (debian-ker...@lists.debian.org) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 SMP Debian 4.18.6-1~bpo9+1 (2018-09-13) [ 0.000000] x86/fpu: x87 FPU will use FSAVE [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000000fffffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved [ 0.000000] bootconsole [earlyser0] enabled [ 0.000000] Notice: NX (Execute Disable) protection missing in CPU! [ 0.000000] DMI not present or invalid. [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000000] last_pfn = 0x10000 max_arch_pfn = 0x100000 [ 0.000000] Disabled [ 0.000000] x86/PAT: MTRRs disabled, skipping PAT initialization too. [ 0.000000] x86/PAT: Configuration [0-7]: WB WT UC- UC WB WT UC- UC [ 0.000000] initial memory mapped: [mem 0x00000000-0x09ffffff] [ 0.000000] Base memory trampoline at [(ptrval)] 9b000 size 16384 [ 0.000000] RAMDISK: [mem 0x0f571000-0x0fa0afff] [ 0.000000] ACPI: Early table checksum verification disabled [ 0.000000] ACPI BIOS Error (bug): A valid RSDP was not found (20180531/tbxfroot-210) [ 0.000000] 0MB HIGHMEM available. [ 0.000000] 256MB LOWMEM available. [ 0.000000] mapped low ram: 0 - 10000000 [ 0.000000] low ram: 0 - 10000000 [ 0.000000] tsc: Fast TSC calibration using PIT [ 0.000000] BRK [0x09a59000, 0x09a59fff] PGTABLE [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.000000] Normal [mem 0x0000000001000000-0x000000000fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009ffff] [ 0.000000] node 0: [mem 0x0000000000100000-0x000000000fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000000fffffff] [ 0.000000] On node 0 totalpages: 65439 [ 0.000000] DMA zone: 40 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 3999 pages, LIFO batch:0 [ 0.000000] Normal zone: 600 pages used for memmap [ 0.000000] Normal zone: 61440 pages, LIFO batch:15 [ 0.000000] Using APIC driver default [ 0.000000] SFI: Simple Firmware Interface v0.81 http://simplefirmware.org [ 0.000000] No local APIC present or hardware disabled [ 0.000000] APIC: disable apic facility [ 0.000000] APIC: switched to apic NOOP [ 0.000000] smpboot: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff] [ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff] [ 0.000000] [mem 0x10000000-0xffefffff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns [ 0.000000] random: get_random_bytes called from start_kernel+0x81/0x47e with crng_init=0 [ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1 [ 0.000000] percpu: Embedded 29 pages/cpu @(ptrval) s86924 r0 d31860 u118784 [ 0.000000] pcpu-alloc: s86924 r0 d31860 u118784 alloc=29*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64799 [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.18.0-0.bpo.1-686 root=UUID=423c6d29-ad6f-4de5-8612-b7dfcf8c9efd ro console=ttyS0,115200n8 earlyprintk=ttyS0,115200n8 apparmor=1 security=apparmor ipv6.disable=1 noisapnp slub_debug=P page_poison=1 slab_nomerge pti=on nomfgpt [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] BRK [0x09a5a000, 0x09a5afff] PGTABLE [ 0.000000] Initializing CPU#0 [ 0.000000] Initializing HighMem for node 0 (00000000:00000000) [ 0.000000] Memory: 243468K/261756K available (6429K kernel code, 634K rwdata, 2032K rodata, 828K init, 424K bss, 18288K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] virtual kernel memory layout: fixmap : 0xffd35000 - 0xfffff000 (2856 kB) cpu_entry : 0xff400000 - 0xff8e1000 (4996 kB) pkmap : 0xff000000 - 0xff400000 (4096 kB) vmalloc : 0xd0800000 - 0xfeffe000 ( 743 MB) lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) .init : 0xc98f3000 - 0xc99c2000 ( 828 kB) .data : 0xc96474e4 - 0xc98e3900 (2673 kB) .text : 0xc9000000 - 0xc96474e4 (6429 kB) [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] ftrace: allocating 28661 entries in 56 pages [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=32 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 2304, nr_irqs: 32, preallocated irqs: 16 [ 0.000000] CPU 0 irqstacks, hard=(ptrval) soft=(ptrval) [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [ttyS0] enabled [ 0.000000] bootconsole [earlyser0] disabled [ 0.004000] APIC: Keep in PIC mode(8259) [ 0.008000] tsc: Fast TSC calibration using PIT [ 0.012000] tsc: Detected 498.057 MHz processor [ 0.016000] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0xe5bc0194ba, max_idle_ns: 881590443460 ns [ 0.020023] Calibrating delay loop (skipped), value calculated using timer frequency.. 996.11 BogoMIPS (lpj=1992228) [ 0.024018] pid_max: default: 32768 minimum: 301 [ 0.028672] Security Framework initialized [ 0.032041] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.036626] AppArmor: AppArmor initialized [ 0.040222] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.044025] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.054233] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0 [ 0.056025] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0 [ 0.060032] Spectre V2 : Spectre mitigation: LFENCE not serializing, switching to generic retpoline [ 0.064015] Spectre V2 : Mitigation: Full generic retpoline [ 0.068014] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.072015] Speculative Store Bypass: Vulnerable [ 0.100164] Freeing SMP alternatives memory: 20K [ 0.111497] smpboot: weird, boot CPU (#0) not listed by the BIOS [ 0.112021] smpboot: SMP disabled [ 0.117232] Performance Events: no PMU driver, software events only. [ 0.120524] Hierarchical SRCU implementation. [ 0.129870] NMI watchdog: Perf event create on CPU 0 failed with -2 [ 0.132018] NMI watchdog: Perf NMI watchdog permanently disabled [ 0.136605] smp: Bringing up secondary CPUs ... [ 0.140028] smp: Brought up 1 node, 1 CPU [ 0.144019] smpboot: Max logical packages: 1 [ 0.148023] smpboot: Total of 1 processors activated (996.11 BogoMIPS) [ 0.156213] devtmpfs: initialized [ 0.163962] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.164040] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.172519] pinctrl core: initialized pinctrl subsystem [ 0.180835] NET: Registered protocol family 16 [ 0.188096] audit: initializing netlink subsys (disabled) [ 0.196046] audit: type=2000 audit(946684836.192:1): state=initialized audit_enabled=0 res=1 [ 0.200354] cpuidle: using governor ladder [ 0.204040] cpuidle: using governor menu [ 0.208698] clocksource: pit: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1601818034827 ns [ 0.219921] PCI: PCI BIOS revision 2.10 entry at 0xfcf35, last bus=0 [ 0.220018] PCI: Using configuration type 1 for base access [ 0.250234] HugeTLB registered 4.00 MiB page size, pre-allocated 0 pages [ 0.256484] ACPI: Interpreter disabled. [ 0.260758] vgaarb: loaded [ 0.264696] EDAC MC: Ver: 3.0.0 [ 0.269256] PCI: Probing PCI hardware [ 0.272053] PCI: root bus 00: using default resources [ 0.272072] PCI: Probing PCI hardware (bus 00) [ 0.272537] PCI host bridge to bus 0000:00 [ 0.276082] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.280054] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff] [ 0.284027] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.288098] pci 0000:00:01.0: [1022:2080] type 00 class 0x060000 [ 0.288157] pci 0000:00:01.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size) [ 0.292688] pci 0000:00:01.2: [1022:2082] type 00 class 0x101000 [ 0.292759] pci 0000:00:01.2: reg 0x10: [mem 0xefff4000-0xefff7fff] [ 0.293492] pci 0000:00:09.0: [1106:3053] type 00 class 0x020000 [ 0.293537] pci 0000:00:09.0: reg 0x10: [io 0x1000-0x10ff] [ 0.293565] pci 0000:00:09.0: reg 0x14: [mem 0xe0000000-0xe00000ff] [ 0.296052] pci 0000:00:09.0: supports D1 D2 [ 0.296069] pci 0000:00:09.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.296701] pci 0000:00:0b.0: [1106:3053] type 00 class 0x020000 [ 0.296747] pci 0000:00:0b.0: reg 0x10: [io 0x1400-0x14ff] [ 0.296774] pci 0000:00:0b.0: reg 0x14: [mem 0xe0040000-0xe00400ff] [ 0.296880] pci 0000:00:0b.0: supports D1 D2 [ 0.296896] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.297507] pci 0000:00:0f.0: [1022:2090] type 00 class 0x060100 [ 0.297667] pci 0000:00:0f.0: reg 0x10: [io 0x6000-0x6007] [ 0.297768] pci 0000:00:0f.0: reg 0x14: [io 0x6100-0x61ff] [ 0.297869] pci 0000:00:0f.0: reg 0x18: [io 0x6200-0x623f] [ 0.298023] pci 0000:00:0f.0: reg 0x20: [io 0x9d00-0x9d7f] [ 0.298124] pci 0000:00:0f.0: reg 0x24: [io 0x9c00-0x9c3f] [ 0.298703] pci 0000:00:0f.2: [1022:209a] type 00 class 0x010180 [ 0.298961] pci 0000:00:0f.2: reg 0x20: [io 0xff00-0xff0f] [ 0.299066] pci 0000:00:0f.2: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 0.300031] pci 0000:00:0f.2: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 0.304028] pci 0000:00:0f.2: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 0.312023] pci 0000:00:0f.2: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 0.316616] pci 0000:00:0f.4: [1022:2094] type 00 class 0x0c0310 [ 0.316723] pci 0000:00:0f.4: reg 0x10: [mem 0xefffe000-0xefffefff] [ 0.317027] pci 0000:00:0f.4: PME# supported from D0 D3hot D3cold [ 0.320265] pci 0000:00:0f.5: [1022:2095] type 00 class 0x0c0320 [ 0.320375] pci 0000:00:0f.5: reg 0x10: [mem 0xefffd000-0xefffdfff] [ 0.320690] pci 0000:00:0f.5: PME# supported from D0 D3hot D3cold [ 0.321327] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.321624] PCI: pci_cache_line_size set to 32 bytes [ 0.324625] clocksource: Switched to clocksource tsc-early [ 0.534503] VFS: Disk quotas dquot_6.6.0 [ 0.538651] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.547529] AppArmor: AppArmor Filesystem Enabled [ 0.552440] pnp: PnP ACPI: disabled [ 0.555967] PnPBIOS: Scanning system for PnP BIOS support... [ 0.561877] PnPBIOS: PnP BIOS support was not detected. [ 0.598366] pci_bus 0000:00: resource 4 [io 0x0000-0xffff] [ 0.598387] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff] [ 0.598858] NET: Registered protocol family 2 [ 0.605771] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.613688] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.620777] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 0.627322] TCP: Hash tables configured (established 2048 bind 2048) [ 0.633944] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.639846] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.646753] NET: Registered protocol family 1 [ 0.651545] PCI: CLS 32 bytes, default 32 [ 0.652330] Unpacking initramfs... [ 1.043439] random: fast init done [ 1.694552] Freeing initrd memory: 4712K [ 1.699579] platform rtc_cmos: registered platform RTC device (no PNP device found) [ 1.710439] alix: system is recognized as "PC Engines ALIX.2 v0.99m" [ 1.724505] Initialise system trusted keyrings [ 1.729411] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 1.775661] zbud: loaded [ 1.782933] pstore: using deflate compression [ 2.716238] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0xe5bc0194ba, max_idle_ns: 881590443460 ns [ 2.735717] clocksource: Switched to clocksource tsc [ 22.052697] Key type asymmetric registered [ 22.056949] Asymmetric key parser 'x509' registered [ 22.062570] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 22.070324] io scheduler noop registered [ 22.074347] io scheduler deadline registered [ 22.079558] io scheduler cfq registered (default) [ 22.084334] io scheduler mq-deadline registered [ 22.092745] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 22.099749] unchecked MSR access error: RDMSR from 0x179 at rIP: 0xc90450d7 (native_read_msr+0x7/0x40) [ 22.109094] Call Trace: [ 22.111574] ? ghes_init+0x12f/0x12f [ 22.115207] extlog_init+0x21/0x318 [ 22.118752] ? driver_register+0x83/0xf0 [ 22.122730] do_one_initcall+0x42/0x1ae [ 22.126620] ? do_early_param+0x7a/0x7a [ 22.130514] kernel_init_freeable+0x159/0x1de [ 22.134926] ? rest_init+0xa0/0xa0 [ 22.138382] kernel_init+0xd/0x100 [ 22.141847] ret_from_fork+0x2e/0x38 [ 22.145687] isapnp: ISA Plug & Play support disabled [ 22.151740] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 22.158688] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 921600) is a NS16550A [ 22.167892] serial8250: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 921600) is a NS16550A [ 22.180786] Linux agpgart interface v0.103 [ 22.188207] i8042: PNP: No PS/2 controller found. [ 22.192991] i8042: Probing ports directly. [ 23.229335] i8042: No controller found [ 23.234030] mousedev: PS/2 mouse device common for all mice [ 23.240817] rtc_cmos rtc_cmos: registered as rtc0 [ 23.245885] rtc_cmos rtc_cmos: alarms up to one day, 114 bytes nvram [ 23.252606] ledtrig-cpu: registered to indicate activity on CPUs [ 23.260443] IPv6: Loaded, but administratively disabled, reboot required to enable [ 23.268058] mip6: Mobile IPv6 [ 23.271037] mip6: mip6_init: can't add xfrm type(destopt) [ 23.276482] NET: Registered protocol family 17 [ 23.281040] mpls_gso: MPLS GSO support [ 23.284847] mce: Unable to init MCE device (rc: -5) [ 23.290380] Using IPI No-Shortcut mode [ 23.294213] sched_clock: Marking stable (23294146933, 0)->(23375162589, -81015656) [ 23.303679] registered taskstats version 1 [ 23.307845] Loading compiled-in X.509 certificates [ 25.725011] Loaded X.509 cert 'secure-boot-test-key-lfaraone: 97c1b25cddf9873ca78a58f3d73bf727d2cf78ff' [ 25.735121] zswap: loaded using pool lzo/zbud [ 25.739966] AppArmor: AppArmor sha1 policy hashing enabled [ 25.750216] rtc_cmos rtc_cmos: setting system clock to 2000-01-01 00:01:01 UTC (946684861) [ 25.798664] Freeing unused kernel image memory: 828K [ 25.808625] Write protecting the kernel text: 6432k [ 25.814017] Write protecting the kernel read-only data: 2036k [ 26.791524] SCSI subsystem initialized [ 26.898999] libata version 3.00 loaded. [ 26.903159] pata_amd 0000:00:0f.2: version 0.4.1 [ 26.948234] scsi host0: pata_amd [ 26.979421] scsi host1: pata_amd [ 26.989329] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14 [ 26.996375] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15 [ 27.160815] ata1.00: CFA: SanDisk SDCFX3-2048, HDX 4.21, max MWDMA2 [ 27.167175] ata1.00: 4001760 sectors, multi 0: LBA [ 27.211101] scsi 0:0:0:0: Direct-Access ATA SanDisk SDCFX3-2 4.21 PQ: 0 ANSI: 5 [ 27.244582] ata2: port disabled--ignoring [ 27.321949] sd 0:0:0:0: [sda] 4001760 512-byte logical blocks: (2.05 GB/1.91 GiB) [ 27.332911] sd 0:0:0:0: [sda] Write Protect is off [ 27.337822] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 27.337972] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 27.352646] sda: sda1 [ 27.359512] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 27.796286] cryptd: max_cpu_qlen set to 1000 [ 28.237122] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 29.339285] systemd[1]: System time before build time, advancing clock. [ 29.597094] systemd[1]: systemd 239 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 29.618809] systemd[1]: No virtualization found in DMI [ 29.618846] systemd[1]: No virtualization found in CPUID [ 29.618940] systemd[1]: Virtualization XEN not found, /proc/xen does not exist [ 29.619041] systemd[1]: This platform does not support /proc/device-tree [ 29.619418] systemd[1]: UML virtualization not found in /proc/cpuinfo. [ 29.619458] systemd[1]: This platform does not support /proc/sysinfo [ 29.619497] systemd[1]: Found VM virtualization none [ 29.619576] systemd[1]: Detected architecture x86. [ 29.625710] systemd[1]: Mounting cgroup to /sys/fs/cgroup/devices of type cgroup with options devices. [ 31.065637] random: systemd: uninitialized urandom read (16 bytes read) [ 31.089383] random: systemd: uninitialized urandom read (16 bytes read) [ 31.116354] random: systemd: uninitialized urandom read (16 bytes read) [ 31.473767] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 31.811410] systemd[170]: Operating on architecture: x86 [ 31.811546] systemd[170]: Operating on architecture: x86 [ 31.818122] systemd[170]: Operating on architecture: x86 [ 31.818808] systemd[170]: Restricting namespace to: . [ 31.818948] systemd[170]: Operating on architecture: x86 [ 31.819095] systemd[170]: Blocking cgroup. [ 31.819238] systemd[170]: Blocking ipc. [ 31.819382] systemd[170]: Blocking net. [ 31.819529] systemd[170]: Blocking mnt. [ 31.819714] systemd[170]: Blocking pid. [ 31.819961] systemd[170]: Blocking user. [ 31.824391] systemd[170]: Blocking uts. [ 31.825705] systemd[170]: Operating on architecture: x86 [ 31.826983] systemd[170]: Failed to add rule for system call set_tls() / -10183, ignoring: Numerical argument out of domain [ 31.827824] systemd[170]: Failed to add rule for system call epoll_wait_old() / -10006, ignoring: Numerical argument out of domain [ 31.838810] systemd[170]: Failed to add rule for system call newfstatat() / -10031, ignoring: Numerical argument out of domain [ 31.839946] systemd[170]: Failed to add rule for system call epoll_ctl_old() / -10005, ignoring: Numerical argument out of domain [ 32.973366] systemd[176]: Operating on architecture: x86 [ 32.973516] systemd[176]: Operating on architecture: x86 [ 32.981229] systemd[176]: Operating on architecture: x86 [ 33.746699] systemd-journald[170]: Received request to flush runtime journal from PID 1 [ 34.455116] AMD Geode RNG detected [ 34.503323] cs5535-mfd 0000:00:0f.0: 5 devices registered. [ 34.546183] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517 [ 34.562235] via_rhine: v1.10-LK1.5.1 2010-10-09 Written by Donald Becker [ 34.672582] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517 [ 34.708442] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 34.756995] via-rhine 0000:00:09.0 eth0: VIA Rhine III (Management Adapter) at (ptrval), 00:0d:b9:12:d0:f4, IRQ 10 [ 34.768247] via-rhine 0000:00:09.0 eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link cde1 [ 34.782628] input: PC Speaker as /devices/platform/pcspkr/input/input2 [ 34.791908] usbcore: registered new interface driver usbfs [ 34.864504] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517 [ 34.885241] usbcore: registered new interface driver hub [ 34.968585] usbcore: registered new device driver usb [ 35.064658] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517 [ 35.089725] Error allocating fallback algo cbc(aes) [ 35.094741] alg: skcipher: Failed to load transform for cbc-aes-geode: -2 [ 35.119031] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 35.170020] via-rhine 0000:00:0b.0 eth1: VIA Rhine III (Management Adapter) at (ptrval), 00:0d:b9:12:d0:f5, IRQ 15 [ 35.181245] via-rhine 0000:00:0b.0 eth1: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000 [ 35.249217] ehci-pci: EHCI PCI platform driver [ 35.259368] Geode LX AES 0000:00:01.2: GEODE AES engine enabled. [ 35.296637] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517 [ 35.308610] ehci-pci 0000:00:0f.5: EHCI Host Controller [ 35.320661] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 35.393184] ehci-pci 0000:00:0f.5: new USB bus registered, assigned bus number 1 [ 35.488485] ehci-pci 0000:00:0f.5: irq 12, io mem 0xefffd000 [ 35.494789] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517 [ 35.608262] ehci-pci 0000:00:0f.5: USB 2.0 started, EHCI 1.00 [ 35.673869] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18 [ 35.682362] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 35.689647] usb usb1: Product: EHCI Host Controller [ 35.694578] usb usb1: Manufacturer: Linux 4.18.0-0.bpo.1-686 ehci_hcd [ 35.701069] usb usb1: SerialNumber: 0000:00:0f.5 [ 36.082504] hub 1-0:1.0: USB hub found [ 36.128459] hub 1-0:1.0: 4 ports detected [ 36.144222] audit: type=1400 audit(1544179683.772:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=210 comm="apparmor_parser" [ 36.195033] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517 [ 36.236314] ohci-pci: OHCI PCI platform driver [ 36.256599] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517 [ 36.279035] ohci-pci 0000:00:0f.4: OHCI PCI host controller [ 36.308506] audit: type=1400 audit(1544179683.772:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=210 comm="apparmor_parser" [ 36.333127] cs5535-mfgpt cs5535-mfgpt: reserved resource region [io 0x6200-0x623f] [ 36.341001] cs5535-mfgpt cs5535-mfgpt: 8 MFGPT timers available [ 36.362988] cs5535-gpio cs5535-gpio: reserved resource region [io 0x6100-0x61ff] [ 36.377915] cs5535-smb cs5535-smb: SCx200 device 'CS5535 ACB0' registered [ 36.395736] ohci-pci 0000:00:0f.4: new USB bus registered, assigned bus number 2 [ 36.460739] gpio-keys-polled gpio-keys-polled.1: unable to claim gpio 24, err=-517 [ 36.481585] ohci-pci 0000:00:0f.4: irq 12, io mem 0xefffe000 [ 36.523387] audit: type=1400 audit(1544179683.776:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=210 comm="apparmor_parser" [ 36.546669] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.1/input/input10 [ 36.644731] via-rhine 0000:00:09.0 enp0s9: renamed from eth0 [ 36.711021] audit: type=1400 audit(1544179684.120:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/chronyd" pid=211 comm="apparmor_parser" [ 36.750652] via-rhine 0000:00:0b.0 enp0s11: renamed from eth1 [ 36.891240] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.18 [ 36.899652] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 36.906930] usb usb2: Product: OHCI PCI host controller [ 36.912210] usb usb2: Manufacturer: Linux 4.18.0-0.bpo.1-686 ohci_hcd [ 36.918699] usb usb2: SerialNumber: 0000:00:0f.4 [ 37.142985] hub 2-0:1.0: USB hub found [ 37.164235] hub 2-0:1.0: 4 ports detected [ 39.068982] random: crng init done [ 39.072611] random: 7 urandom warning(s) missed due to ratelimiting
