Hi Steve,
On Sun, 5 Sep 2021 17:01:18 +0100 Steve McIntyre <st...@einval.com> wrote:
> On Sat, Sep 04, 2021 at 06:50:16PM +0100, Steve McIntyre wrote:> >
> >I have a synquacer here still and I'll take a look. I noticed on
> >bullseye release day that USB stuff didn't seem to work in the
> >installer on the synquacer either. Maybe there's been a regression in
> >config. :-/
> >
> >I'll take a look...
>
> Hmmm, booting 5.10.0-0.bpo.8-arm64 here does not work at all. I'm
> seeing a lot of errors around DMA setup, e.g.:
>
> [ 0.142797] OF: translation of DMA address(0) to CPU address failed node()
> [ 0.142824] sram 45200000.sram: Invalid size 0x1 for dma-range(s)
> [ 0.142991] OF: translation of DMA address(0) to CPU address failed node()
> [ 0.143008] uart-pl011 2a400000.uart: Invalid size 0x1 for dma-range(s)
> ...
> [ 3.843964] OF: translation of DMA address(0) to CPU address failed node()
> [ 3.850875] armv8-pmu pmu: Invalid size 0x1 for dma-range(s)
> [ 3.857518] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
> ...
> [ 3.954986] OF: translation of DMA address(0) to CPU address failed node()
> ...
> [ 4.391564] OF: translation of DMA address(0) to CPU address failed node()
> [ 4.398449] pcieport 0000:00:00.0: Invalid size 0x1 for dma-range(s)
> [ 4.405253] OF: translation of DMA address(0) to CPU address failed node()
> [ 4.412161] pcieport 0000:01:01.0: Invalid size 0x1 for dma-range(s)
> [ 4.418885] OF: translation of DMA address(0) to CPU address failed node()
> [ 4.425778] pcieport 0000:01:03.0: Invalid size 0x1 for dma-range(s)
> [ 4.432487] OF: translation of DMA address(0) to CPU address failed node()
> [ 4.439385] pcieport 0000:01:05.0: Invalid size 0x1 for dma-range(s)
> [ 4.446095] OF: translation of DMA address(0) to CPU address failed node()
> [ 4.452988] pcieport 0000:01:07.0: Invalid size 0x1 for dma-range(s)
> [ 4.459693] pci 0000:04:00.0: enabling device (0000 -> 0002)
> [ 4.465488] OF: translation of DMA address(0) to CPU address failed node()
> ...
> [ 4.472385] pci-host-generic 70000000.pcie: Invalid size 0x1 for dma-range(s)
>
I'm seeing the same errors as you about pcieport and others:
[ 1.834588] OF: translation of DMA address(0) to CPU address
failed node()
[ 1.834617] uart-pl011 2a400000.uart: Invalid size 0x1 for
dma-range(s)
[ 5.708968] OF: translation of DMA address(0) to CPU address
failed node()
[ 5.715885] armv8-pmu pmu: Invalid size 0x1 for dma-range(s)
[ 5.820268] OF: translation of DMA address(0) to CPU address
failed node()
[ 5.827159] pci-host-generic 60000000.pcie: Invalid size 0x1
for dma-range(s)
[ 6.355712] pci 0000:00:00.0: bridge window [io
0x1000-0x2fff]
[ 6.361816] pci 0000:00:00.0: bridge window [mem
0x68000000-0x682fffff]
[ 6.368676] OF: translation of DMA address(0) to CPU address
failed node()
[ 6.375564] pcieport 0000:00:00.0: Invalid size 0x1 for
dma-range(s)
[ 6.382390] OF: translation of DMA address(0) to CPU address
failed node()
[ 6.389299] pcieport 0000:01:01.0: Invalid size 0x1 for
dma-range(s)
[ 6.396049] OF: translation of DMA address(0) to CPU address
failed node()
[ 6.402940] pcieport 0000:01:03.0: Invalid size 0x1 for
dma-range(s)
[ 6.409669] OF: translation of DMA address(0) to CPU address
failed node()
[ 6.416564] pcieport 0000:01:05.0: Invalid size 0x1 for
dma-range(s)
[ 6.423283] OF: translation of DMA address(0) to CPU address
failed node()
[ 6.430177] pcieport 0000:01:07.0: Invalid size 0x1 for
dma-range(s)
[ 6.436904] pci 0000:04:00.0: enabling device (0000 -> 0002)
[ 6.442721] OF: translation of DMA address(0) to CPU address
failed node()
[ 6.449620] pci-host-generic 70000000.pcie: Invalid size 0x1
for dma-range(s)
And later on i have slightly different errors from ahci, xhci_hcd and more:
Starting version 241
[ 7.883272] OF: translation of DMA address(0) to CPU address
failed node()
[ 7.890215] mb86s70-gpio 51000000.gpio: Invalid size 0x1 for
dma-range(s)
[ 7.897692] OF: translation of DMA address(0) to CPU address
failed node()
[ 7.898886] pps_core: LinuxPPS API ver. 1 registered
[ 7.904613] gpio-keys gpio-keys: Invalid size 0x1 for
dma-range(s)
[ 7.909598] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
Rodolfo Giometti <giome...@linux.it>
[ 7.910853] libphy: Fixed MDIO Bus: probed
[ 7.916254] input: gpio-keys as
/devices/platform/gpio-keys/input/input0
[ 7.932281] SCSI subsystem initialized
[ 7.942529] PTP clock support registered
[ 7.943568] usbcore: registered new interface driver usbfs
[ 7.952112] usbcore: registered new interface driver hub
[ 7.952607] OF: translation of DMA address(0) to CPU address
failed node()
[ 7.957545] usbcore: registered new device driver usb
[ 7.964340] netsec 522d0000.ethernet: Invalid size 0x1 for
dma-range(s)
[ 7.976147] netsec 522d0000.ethernet: hardware revision 5.65
[ 7.982366] libphy: SNI NETSEC MDIO: probed
[ 7.985915] e1000e: Intel(R) PRO/1000 Network Driver
[ 7.991539] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 7.997560] OF: translation of DMA address(0) to CPU address
failed node()
[ 8.000147] netsec 522d0000.ethernet eth0 (uninitialized):
register_netdev() failed
[ 8.004452] e1000e 0000:03:00.0: Invalid size 0x1 for
dma-range(s)
[ 8.018385] e1000e 0000:03:00.0: enabling device (0000 ->
0002)
[ 8.018769] OF: translation of DMA address(0) to CPU address
failed node()
[ 8.024528] e1000e 0000:03:00.0: Interrupt Throttling Rate
(ints/sec) set to dynamic conservative mode
[ 8.031225] ahci 0000:02:00.0: Invalid size 0x1 for
dma-range(s)
[ 8.031628] OF: translation of DMA address(0) to CPU address
failed node()
[ 8.031637] xhci_hcd 0000:04:00.0: Invalid size 0x1 for
dma-range(s)
[ 8.031753] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 8.031782] xhci_hcd 0000:04:00.0: new USB bus registered,
assigned bus number 1
[ 8.045912] xhci_hcd 0000:04:00.0: can't setup: -12
[ 8.053436] xhci_hcd 0000:04:00.0: USB bus 1 deregistered
[ 8.053462] xhci_hcd 0000:04:00.0: init 0000:04:00.0 fail, -12
[ 8.060092] ahci 0000:02:00.0: SSS flag set, parallel bus scan
disabled
[ 8.065067] xhci_hcd: probe of 0000:04:00.0 failed with error
-12
[ 8.072512] ahci 0000:02:00.0: AHCI 0001.0200 32 slots 2 ports
6 Gbps 0x3 impl SATA mode
[ 8.092853] e1000e 0000:03:00.0 0000:03:00.0 (uninitialized):
registered PHC clock
[ 8.095211] ahci 0000:02:00.0: flags: 64bit ncq sntf stag led
clo pmp pio slum part ccc sxs
[ 8.127181] ahci 0000:02:00.0: failed to start port 0
(errno=-12)
[ 8.133429] ahci: probe of 0000:02:00.0 failed with error -12
[ 8.136094] netsec 522d0000.ethernet: init failed
[ 8.143976] netsec: probe of 522d0000.ethernet failed with
error -12
[ 8.154679] e1000e 0000:03:00.0 eth0: (PCI
Express:2.5GT/s:Width x1) 68:05:ca:3f:df:be
[ 8.162643] e1000e 0000:03:00.0 eth0: Intel(R) PRO/1000 Network
Connection
[ 8.169547] e1000e 0000:03:00.0 eth0: MAC: 3, PHY: 8, PBA No:
E46981-008
[ 8.181197] e1000e 0000:03:00.0 enp3s0: renamed from eth0
Begin: Loading essential drivers ... done.
Do you think thet the failing DMA setup could be the cause of
all the failures?
> [ 5.728589] xhci_hcd: probe of 0000:04:00.0 failed with error -12
> [ 5.734347] sp : ffff8000142bbb10
> [ 5.734351] x29: ffff8000142bbb10 x28: 0000000000000000
> [ 5.734358] x27: ffff000801ebf848 x26: ffffffffffffffff
> [ 5.768201] x25: 0000000000000080 x24: 0000000000010000
> [ 5.773514] x23: ffff00080176ac10 x22: 0000000889b60080
> [ 5.778826] x21: 0000000000000000 x20: 0000000000000000
> [ 5.784139] x19: ffff8000117c9788 x18: 0000000000000020
> [ 5.789451] x17: ffff00080833da00 x16: 0000000000000080
> [ 5.794763] x15: ffffffffffffffff x14: 2820776f6c667265
> [ 5.800076] x13: 766f203633353536 x12: 2b66666666666666
> [ 5.805389] x11: 6666666666666666 x10: 6678302072646461
> [ 5.810701] x9 : ffff80001011159c x8 : 62202c6666666666
> [ 5.816013] x7 : 666666206b73616d x6 : ffff00087f4647c0
> [ 5.821325] x5 : ffff8000142bb828 x4 : 0000000000000000
> [ 5.826637] x3 : 0000000000000000 x2 : 00000000ffffffff
> [ 5.831949] x1 : 3082d45f0379e900 x0 : 0000000000000000
> [ 5.837262] Call trace:
> [ 5.839708] swiotlb_map+0x294/0x2a8
> [ 5.843281] dma_map_page_attrs+0xec/0x228
> [ 5.847382] sdhci_setup_host+0xa8c/0xee8 [sdhci]
Cheers,
Luca
