Package: munin-node
Version: 2.0.67-3
Severity: wishlist
Hello
I knew this exact same wish was in #488360
But I have new information to add to it.
In that old bug report the user has SAS drives, and there are not that much
information
which SAS drives could report, so it was not a problem with the controller.
I also have disks on a controller which are only available through cciss,
but my disks are SATA disks which report fully normal data for SATA disks.
So please add support for cciss for the smart_ plugin ... :-)
Here is the output for example:
(This is the output of my 4th disk, disks 1-3 (cciss,0 ... cciss,2) have errors
so I only show disk 4 which has no errors.)
smartctl /dev/sda -d cciss,3 -a
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-20-amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST3000DM001-1CH166
Serial Number: W1F7MF94
LU WWN Device Id: 5 000c50 06a73a16e
Firmware Version: CC27
User Capacity: 3.000.592.982.016 bytes [3,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Jan 22 11:31:13 2023 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 584) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 322) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3085) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 118 099 006 Pre-fail Always
- 183875504
3 Spin_Up_Time 0x0003 094 094 000 Pre-fail Always
- 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always
- 60
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always
- 0
7 Seek_Error_Rate 0x000f 071 053 030 Pre-fail Always
- 43093110146
9 Power_On_Hours 0x0032 079 079 000 Old_age Always
- 18887
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always
- 21
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always
- 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
- 0
188 Command_Timeout 0x0032 100 099 000 Old_age Always
- 1 1 1
189 High_Fly_Writes 0x003a 097 097 000 Old_age Always
- 3
190 Airflow_Temperature_Cel 0x0022 074 045 045 Old_age Always
In_the_past 26 (Min/Max 25/27)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always
- 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 18
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always
- 3413
194 Temperature_Celsius 0x0022 026 055 000 Old_age Always
- 26 (0 4 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline
- 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline
- 18790h+46m+22.761s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline
- 17553216526
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline
- 48407502391
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Extended offline Completed without error 00% 18833 -
# 2 Short offline Completed without error 00% 18828 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Jochen
-- System Information:
Debian Release: 11.6
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable-security'), (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 5.10.0-20-amd64 (SMP w/4 CPU threads)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8), LANGUAGE not set
Shell: /bin/sh linked to /usr/bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled
Versions of packages munin-node depends on:
ii init-system-helpers 1.60
ii libnet-server-perl 2.009-2
ii lsb-base 11.1.0
ii munin-common 2.0.67-3
ii munin-plugins-core 2.0.67-3
ii netbase 6.3
ii perl 5.32.1-4+deb11u2
Versions of packages munin-node recommends:
ii gawk 1:5.1.0-1
ii git 1:2.30.2-1
ii jo 1.3-2
ii jq 1.6-2.1
ii man-db [man] 2.9.4-2
ii munin-plugins-extra 2.0.67-3
ii perl-doc 5.32.1-4+deb11u2
ii procps 2:3.3.17-5
Versions of packages munin-node suggests:
ii munin 2.0.67-3
pn munin-plugins-java <none>
-- Configuration Files:
/etc/munin/plugin-conf.d/README [Errno 13] Permission denied:
'/etc/munin/plugin-conf.d/README'
/etc/munin/plugin-conf.d/munin-node [Errno 13] Permission denied:
'/etc/munin/plugin-conf.d/munin-node'
-- no debconf information
