On Sun, 21 Jan 2007 23:48:16 +0100 Aurelien Jarno <[EMAIL PROTECTED]> wrote:
> Hi, Hi Aurelien, > I have just uploaded a new version of the rt2x00 package > (0cvs20070121-1) that may fix the bug you reported. It is currently > available in http://incoming.debian.org and will be available in about > 12 hours on the mirrors. > > Could you please test it? done, i get a hard lockup of the machine everytime i try to scan networks, then i have to reboot. Maybe it's useful to know that i don't have currently an access point i can connect to. These are the steps to reproduce, taken from bug #405746: iwconfig wlan0 mode managed iwconfig wlan0 essid foo iwconfig wlan0 channel 6 iwconfig wlan0 key open ifconfig wlan0 up iwlist wlan0 scan I get this on /var/log/messages with rt61pci module debug enabled: Jan 28 12:59:07 eurasia kernel: rt61pci->rt61pci_conf_tx: Info - Configured TX ring 0 - CWmin: 4, CWmax: 10, Aifs: 2. Jan 28 12:59:07 eurasia kernel: rt61pci->rt61pci_conf_tx: Info - Configured TX ring 1 - CWmin: 4, CWmax: 10, Aifs: 2. Jan 28 12:59:07 eurasia kernel: rt61pci->rt61pci_conf_tx: Info - Configured TX ring 2 - CWmin: 4, CWmax: 10, Aifs: 2. Jan 28 12:59:07 eurasia kernel: rt61pci->rt61pci_conf_tx: Info - Configured TX ring 3 - CWmin: 4, CWmax: 10, Aifs: 2. Jan 28 12:59:07 eurasia kernel: rt61pci->rt61pci_conf_tx: Info - Configured TX ring 4 - CWmin: 4, CWmax: 10, Aifs: 2. Jan 28 12:59:07 eurasia kernel: rt61pci->rt61pci_conf_tx: Info - Configured TX ring 7 - CWmin: 5, CWmax: 10, Aifs: 2. Jan 28 12:59:20 eurasia kernel: rt61pci->rt61pci_config_channel: Info - Switching channel. RF1: 0x00002ccc, RF2: 0x0000478e, RF3: 0x0006b655, RF4: 0x000ffa1f. Jan 28 12:59:20 eurasia kernel: rt61pci->rt61pci_init_bbp: Notice - Waiting for BBP register. Jan 28 12:59:20 eurasia kernel: rt61pci->rt61pci_config_channel: Info - Switching channel. RF1: 0x00002ccc, RF2: 0x00004786, RF3: 0x0006b655, RF4: 0x000ffa0b. Jan 28 12:59:20 eurasia kernel: rt61pci->rt61pci_init_channel_time: Notice - Channel change time has been set to 8000. I see on boot: Jan 28 13:00:40 eurasia kernel: Loading module: rt61pci - CVS (20070104) by http://rt2x00.serialmonkey.com. but dpkg gives me: rt2x00-modules-2.6.18-3-k7 0cvs20070121-1+2.6.18-8 this is lspci -nn -vvv of my card: 00:09.0 Network controller [0280]: RaLink RT2561/RT61 rev B 802.11g [1814:0302] Subsystem: Micro-Star International Co., Ltd. Unknown device [1462:b834] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 193 Region 0: Memory at dfff8000 (32-bit, non-prefetchable) [size=32K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- HTH, Riccardo -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
