Package: acpid Version: 1.0.6-9 Hello,
when I upgraded acpid to 1.0.6-9 the computer crashed and reboot. My computer only boots on recovery mode now. Aptitude is unusable and when I try a "dpkg --configure -a" to finish installation process, the computer reboots. I'm using Debian Lenny with 2.6.22 kernel. Other kernels do not boot (http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=482964). Here is a "lspci -vvv" http://www.pi-et-ro.net/lspci.txt *********************************************** 00:00.0 Host bridge: VIA Technologies, Inc. VT8374 P4X400 Host Controller/AGP Bridge (rev 82) Subsystem: ASUSTeK Computer Inc. Device 8105 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ INTx- Latency: 8 Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M] Capabilities: [80] AGP version 3.5 Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2- ,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: agpgart-via Kernel modules: via-agp 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: df100000-df6fffff Prefetchable memory behind bridge: bf000000-deffffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2- ,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel modules: shpchp 00:0a.0 SCSI storage controller: Adaptec AHA-7850 (rev 03) Subsystem: Adaptec Device 7850 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (1000ns min, 1000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at ee00 [disabled] [size=256] Region 1: Memory at dfc00000 (32-bit, non-prefetchable) [size=4K] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2- ,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: aic7xxx Kernel modules: aic7xxx 00:0c.0 FireWire (IEEE 1394): NEC Corporation uPD72874 IEEE1394 OHCI 1.1 3-port PHY-Link Ctrlr (rev 01) (prog-if 10) Subsystem: NEC Corporation uPD72874 IEEE1394 OHCI 1.1 3-port PHY-Link Ctrlr Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (5000ns min, 11000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at dfd00000 (32-bit, non-prefetchable) [size=4K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME+ Kernel driver in use: firewire_ohci Kernel modules: firewire-ohci 00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80) Subsystem: ASUSTeK Computer Inc. Device 80ed Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin B routed to IRQ 16 Region 0: I/O ports at efe0 [size=8] Region 1: I/O ports at efac [size=4] Region 2: I/O ports at efa0 [size=8] Region 3: I/O ports at efa8 [size=4] Region 4: I/O ports at ef90 [size=16] Region 5: I/O ports at e800 [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2- ,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: sata_via Kernel modules: sata_via 00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: ASUSTeK Computer Inc. Device 80ed Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 16 Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] Region 4: I/O ports at fc00 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2- ,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: VIA_IDE Kernel modules: via82cxxx 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) Subsystem: ASUSTeK Computer Inc. Device 80ed Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 19 Region 4: I/O ports at edc0 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) Subsystem: ASUSTeK Computer Inc. Device 80ed Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 19 Region 4: I/O ports at ef00 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) Subsystem: ASUSTeK Computer Inc. Device 80ed Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at ef20 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) Subsystem: ASUSTeK Computer Inc. Device 80ed Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at ef40 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME+ Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if 20) Subsystem: ASUSTeK Computer Inc. Device 80ed Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 128 bytes Interrupt: pin C routed to IRQ 19 Region 0: Memory at dfe00000 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South] Subsystem: ASUSTeK Computer Inc. Device 80ed Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2- ,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel modules: i2c-viapro 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60) Subsystem: ASUSTeK Computer Inc. Device 80b0 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 21 Region 0: I/O ports at e000 [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2- ,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: VIA 82xx Audio Kernel modules: snd-via82xx 00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 80) Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 21 Region 0: I/O ports at 1000 [size=256] Capabilities: [d0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2- ,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel modules: snd-via82xx-modem 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78) Subsystem: ASUSTeK Computer Inc. Device 80ed Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (750ns min, 2000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 20 Region 0: I/O ports at e400 [size=256] Region 1: Memory at dff00000 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: via-rhine Kernel modules: via-rhine 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R300 NE [Radeon 9500 Pro] Subsystem: Hercules Device 0004 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (2000ns min), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at d000 [size=256] Region 2: Memory at df600000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at df500000 [disabled] [size=128K] Capabilities: [58] AGP version 3.0 Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none> Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2- ,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel modules: radeonfb 01:00.1 Display controller: ATI Technologies Inc Radeon R300 [Radeon 9500 Pro] (Secondary) Subsystem: Hercules Device 0005 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (2000ns min), Cache Line Size: 64 bytes Region 0: Memory at c8000000 (32-bit, prefetchable) [size=128M] Region 1: Memory at df400000 (32-bit, non-prefetchable) [size=64K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2- ,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- *********************************************** And my "dmesg" http://www.pi-et-ro.net/dmesg.txt *********************************************** Linux version 2.6.22-2-686 (Debian 2.6.22-4) ([EMAIL PROTECTED]) (gcc version 4.1.3 20070812 (prerelease) (Debian 4.1.2-15)) #1 SMP Fri Aug 31 00:24:01 UTC 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003ff30000 (usable) BIOS-e820: 000000003ff30000 - 000000003ff40000 (ACPI data) BIOS-e820: 000000003ff40000 - 000000003fff0000 (ACPI NVS) BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved) BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000ff780 Entering add_active_range(0, 0, 261936) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 HighMem 229376 -> 261936 early_node_map[1] active PFN ranges 0: 0 -> 261936 On node 0 totalpages: 261936 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 HighMem zone: 254 pages used for memmap HighMem zone: 32306 pages, LIFO batch:7 DMI 2.3 present. ACPI: RSDP 000FA3A0, 0024 (r2 ACPIAM) ACPI: XSDT 3FF30100, 003C (r1 A M I OEMXSDT 11000312 MSFT 97) ACPI: FACP 3FF30290, 00F4 (r3 A M I OEMFACP 11000312 MSFT 97) ACPI: DSDT 3FF303F0, 3562 (r1 A0017 A0017001 1 INTL 2002026) ACPI: FACS 3FF40000, 0040 ACPI: APIC 3FF30390, 0052 (r1 A M I OEMAPIC 11000312 MSFT 97) ACPI: OEMB 3FF40040, 0040 (r1 A M I AMI_OEM 11000312 MSFT 97) ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:3 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:bf7c0000) Built 1 zonelists. Total pages: 259890 Kernel command line: root=/dev/hdb5 ro single mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 2800.206 MHz processor. Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1033776k/1047744k available (1688k kernel code, 13268k reserved, 653k data, 244k init, 130240k highmem) virtual kernel memory layout: fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc034f000 - 0xc038c000 ( 244 kB) .data : 0xc02a62bf - 0xc03497e4 ( 653 kB) .text : 0xc0100000 - 0xc02a62bf (1688 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 5607.80 BogoMIPS (lpj=11215603) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000041d 00000000 00000000 monitor/mwait feature present. using mwait in idle threads. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Hyper-Threading is disabled CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b180 0000041d 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 11k freed ACPI: Core revision 20070126 CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 03 Total of 1 processors activated (5607.80 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 Brought up 1 CPUs Booting paravirtualized kernel on bare hardware NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: (supports S0 S1 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: enabled onboard AC97/MC97 devices ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 14 devices ACPI: ACPI bus type pnp unregistered PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NET: Registered protocol family 8 NET: Registered protocol family 20 ACPI: RTC can wake from S4 pnp: 00:09: iomem range 0xfec00000-0xfec00fff has been reserved pnp: 00:09: iomem range 0xfee00000-0xfee00fff has been reserved pnp: 00:09: iomem range 0xfff80000-0xffffffff could not be reserved Time: tsc clocksource has been installed. pnp: 00:0c: ioport range 0x680-0x6ff has been reserved pnp: 00:0d: iomem range 0x0-0x9ffff could not be reserved pnp: 00:0d: iomem range 0xc0000-0xdffff could not be reserved pnp: 00:0d: iomem range 0xe0000-0xfffff could not be reserved pnp: 00:0d: iomem range 0x100000-0x3ffeffff could not be reserved PCI: Bridge: 0000:00:01.0 IO window: d000-dfff MEM window: df100000-df6fffff PREFETCH window: bf000000-deffffff PCI: Setting latency timer of device 0000:00:01.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 1293k freed audit: initializing netlink socket (disabled) audit(1212184489.188:1): initialized highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: VIA PCI bridge detected. Disabling DAC. PCI: Bypassing VIA 8237 APIC De-Assert Message Boot video device is 0000:01:00.0 isapnp: Scanning for PnP cards... Switched to high resolution mode on CPU 0 isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI No-Shortcut mode Freeing unused kernel memory: 244k freed Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.1 ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 16 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... input: AT Translated Set 2 keyboard as /class/input/input0 hda: WDC WD800JB-00ETA0, ATA DISK drive hdb: WDC WD1200JB-00REA0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: JLMS XJ-HD166S, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 SCSI subsystem initialized libata version 2.21 loaded. hda: max request size: 512KiB hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hdb: max request size: 512KiB hdb: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100) hdb: cache flushes supported hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 > EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Linux agpgart interface v0.102 (c) Dave Jones agpgart: Detected VIA PT800 chipset agpgart: AGP aperture is 64M @ 0xe0000000 ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 16 (level, low) -> IRQ 17 firewire_ohci: Added fw-ohci device 0000:00:0c.0, OHCI version 1.10 firewire_ohci: swap not done yet ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 18 ahc_pci:0:10:0: Host Adapter Bios disabled. Using default SCSI device parameters hdc: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 firewire_core: created new fw device fw0 (0 config rom retries) USB Universal Host Controller Interface driver v3.0 Real Time Clock Driver v1.12ac input: PC Speaker as /class/input/input1 via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 logips2pp: Detected unknown logitech mouse model 57 input: ImExPS/2 Logitech Explorer Mouse as /class/input/input2 parport_pc 00:07: reported by Plug and Play ACPI parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 <Adaptec 2902/04/10/15/20C/30C SCSI adapter> aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 19 uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:10.0: irq 19, io base 0x0000edc0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 19 uhci_hcd 0000:00:10.1: UHCI Host Controller uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.1: irq 19, io base 0x0000ef00 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 19 uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.2: irq 19, io base 0x0000ef20 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 19 uhci_hcd 0000:00:10.3: UHCI Host Controller uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.3: irq 19, io base 0x0000ef40 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 19 ehci_hcd 0000:00:10.4: EHCI Host Controller ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:10.4: irq 19, io mem 0xdfe00000 ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected sata_via 0000:00:0f.0: version 2.2 ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 16 sata_via 0000:00:0f.0: routed to hard irq line 10 scsi1 : sata_via scsi2 : sata_via ata1: SATA max UDMA/133 cmd 0x0001efe0 ctl 0x0001efae bmdma 0x0001ef90 irq 16 ata2: SATA max UDMA/133 cmd 0x0001efa0 ctl 0x0001efaa bmdma 0x0001ef98 irq 16 ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300) ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300) ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 20 eth0: VIA Rhine II at 0x1e400, 00:0e:a6:be:b0:b4, IRQ 20. eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1. PCI: Enabling device 0000:00:11.6 (0000 -> 0001) ACPI: PCI Interrupt 0000:00:11.6[C] -> GSI 22 (level, low) -> IRQ 21 usb 5-8: new high speed USB device using ehci_hcd and address 2 usb 5-8: configuration #1 chosen from 1 choice hub 5-8:1.0: USB hub found hub 5-8:1.0: 4 ports detected PCI: Setting latency timer of device 0000:00:11.6 to 64 ACPI: PCI interrupt for device 0000:00:11.6 disabled VIA 82xx Modem: probe of 0000:00:11.6 failed with error -13 ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:11.5 to 64 codec_read: codec 0 is not valid [0x107e5370] codec_read: codec 0 is not valid [0x107e5370] codec_read: codec 0 is not valid [0x107e5370] codec_read: codec 0 is not valid [0x107e5370] Adding 3148732k swap on /dev/hdb2. Priority:-1 extents:1 across:3148732k EXT3 FS on hdb3, internal journal usbcore: registered new interface driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for Handspring Visor / Palm OS drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 3.5 drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 5.0 usbcore: registered new interface driver visor drivers/usb/serial/visor.c: USB HandSpring Visor / Palm OS driver device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [EMAIL PROTECTED] fuse init (API version 7.8) kjournald starting. Commit interval 5 seconds EXT3 FS on hdb5, internal journal EXT3-fs: mounted filesystem with ordered data mode. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 NET: Registered protocol family 10 lo: Disabled Privacy Extensions ******************************************* Thanks for help -- Cordialement. Louis-Maurice De Sousa -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
