Package: linux-2.6 Version: 2.6.32-5 Severity: important Hi, The Bug seems for me a little bit strange :-) My NIC r8169 works perfect. But after 2 month or so i have a problem with my NIC. If i reboot my PC, my NIC isn't dedected correctly. I make reboots again but it doesn't work. But if i use Knoppix 6.1 ones. My Debian Squeeze system (NIC) works perfect. But after reboot its still the same problem!
Here is the dmesg output, if the NIC doesn't work: [ 4.785169] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 4.785236] r8169 0000:00:09.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 4.785308] r8169 0000:00:09.0: no PCI Express capability [ 4.867561] eth0: RTL8169sc/8110sc at 0xf7c94000, 00:00:00:00:c0:e7, XID 18000000 IRQ 18 [ 4.871974] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 4.872048] r8169 0000:00:0b.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 4.872113] r8169 0000:00:0b.0: no PCI Express capability [ 4.875112] eth1: RTL8169sc/8110sc at 0xf7cf0000, 00:00:00:00:c0:e8, XID 18000000 IRQ 19 [ 9.128518] udev: starting version 151 [ 9.674896] udev: renamed network interface eth1 to eth3 [ 9.772643] udev: renamed network interface eth0 to eth2 Here is the dmesg output, if the NIC works: [ 4.858872] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 4.858935] r8169 0000:00:09.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 4.859007] r8169 0000:00:09.0: no PCI Express capability [ 4.868080] eth0: RTL8169sc/8110sc at 0xf7ce2000, 00:30:18:b0:c0:e7, XID 18000000 IRQ 18 [ 4.934420] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 4.934481] r8169 0000:00:0b.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 4.934557] r8169 0000:00:0b.0: no PCI Express capability [ 4.937598] eth1: RTL8169sc/8110sc at 0xf7d2e000, 00:30:18:b0:c0:e8, XID 18000000 IRQ 19 [ 9.070839] udev: starting version 151 [ 13.879190] r8169: eth0: link up [ 14.776483] r8169: eth1: link down [ 14.777584] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 23.928048] eth0: no IPv6 routers present Here is the dmesg output of Knoppix 6.1: [ 23.060011] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 23.060011] r8169 0000:00:09.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 23.060011] r8169 0000:00:09.0: no PCI Express capability [ 23.060011] eth0: RTL8169sc/8110sc at 0xf8684000, 00:30:18:b0:c0:e7, XID 18000000 IRQ 18 [ 23.060846] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 23.060878] r8169 0000:00:0b.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 23.060940] r8169 0000:00:0b.0: no PCI Express capability [ 23.061847] eth1: RTL8169sc/8110sc at 0xf8032000, 00:30:18:b0:c0:e8, XID 18000000 IRQ 19 As you can see, the hardware address 0xf7ce2000 differ. Regards Spitzauer -- Package-specific info: ** Version: Linux version 2.6.32-trunk-686 (Debian 2.6.32-5) ([email protected]) (gcc version 4.3.4 (Debian 4.3.4-6) ) #1 SMP Sun Jan 10 06:32:16 UTC 2010 ** Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-trunk-686 root=UUID=9257d9fe-4c83-45ab-b051-fadad47fbda3 ro quiet ** Not tainted ** Kernel log: [70752.088942] ata1.00: configured for UDMA/33 [70752.088993] ata1: EH complete [70785.723240] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 [70785.723286] ata1.00: BMDMA stat 0x25 [70785.723318] ata1.00: failed command: READ DMA EXT [70785.723369] ata1.00: cmd 25/00:80:3f:01:54/00:00:e6:00:00/e0 tag 0 dma 65536 in [70785.723376] res 51/84:5f:3f:01:54/84:00:e6:00:00/e0 Emask 0x10 (ATA bus error) [70785.723454] ata1.00: status: { DRDY ERR } [70785.723481] ata1.00: error: { ICRC ABRT } [70785.723522] ata1: soft resetting link [70785.893138] ata1.00: configured for UDMA/33 [70785.893190] ata1: EH complete [70804.549345] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 [70804.549392] ata1.00: BMDMA stat 0x25 [70804.549425] ata1.00: failed command: READ DMA EXT [70804.549476] ata1.00: cmd 25/00:80:3f:c2:6b/00:00:e6:00:00/e0 tag 0 dma 65536 in [70804.549483] res 51/84:4f:3f:c2:6b/84:00:e6:00:00/e0 Emask 0x10 (ATA bus error) [70804.549561] ata1.00: status: { DRDY ERR } [70804.549589] ata1.00: error: { ICRC ABRT } [70804.549630] ata1: soft resetting link [70804.721120] ata1.00: configured for UDMA/33 [70804.721174] ata1: EH complete [71080.916948] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 [71080.916992] ata1.00: BMDMA stat 0x25 [71080.917024] ata1.00: failed command: READ DMA EXT [71080.917074] ata1.00: cmd 25/00:80:3f:d1:f9/00:00:e7:00:00/e0 tag 0 dma 65536 in [71080.917082] res 51/84:4f:3f:d1:f9/84:00:e7:00:00/e0 Emask 0x10 (ATA bus error) [71080.917160] ata1.00: status: { DRDY ERR } [71080.917187] ata1.00: error: { ICRC ABRT } [71080.917228] ata1: soft resetting link [71081.089061] ata1.00: configured for UDMA/33 [71081.089099] ata1: EH complete [71178.781442] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 [71178.781490] ata1.00: BMDMA stat 0x25 [71178.781523] ata1.00: failed command: READ DMA EXT [71178.781574] ata1.00: cmd 25/00:80:3f:42:88/00:00:e8:00:00/e0 tag 0 dma 65536 in [71178.781581] res 51/84:0f:3f:42:88/84:00:e8:00:00/e0 Emask 0x10 (ATA bus error) [71178.781692] ata1.00: status: { DRDY ERR } [71178.781720] ata1.00: error: { ICRC ABRT } [71178.781761] ata1: soft resetting link [71178.953352] ata1.00: configured for UDMA/33 [71178.953407] ata1: EH complete [71247.868871] md: md127: data-check done. [88277.210559] lo: Disabled Privacy Extensions [88277.654580] lo: Disabled Privacy Extensions [88299.635551] lo: Disabled Privacy Extensions [88300.069836] lo: Disabled Privacy Extensions [88407.060758] lo: Disabled Privacy Extensions [88407.496930] lo: Disabled Privacy Extensions [92326.187649] lo: Disabled Privacy Extensions [92326.627029] lo: Disabled Privacy Extensions [93523.759658] lo: Disabled Privacy Extensions [93524.772856] lo: Disabled Privacy Extensions [93525.060123] lo: Disabled Privacy Extensions [93525.510123] lo: Disabled Privacy Extensions [93811.409593] lo: Disabled Privacy Extensions [93811.834768] lo: Disabled Privacy Extensions [93837.039956] lo: Disabled Privacy Extensions [93837.485213] lo: Disabled Privacy Extensions [93837.864326] lo: Disabled Privacy Extensions [93838.480740] lo: Disabled Privacy Extensions [93839.284390] lo: Disabled Privacy Extensions [93840.000768] lo: Disabled Privacy Extensions [93840.483339] lo: Disabled Privacy Extensions [93841.071955] lo: Disabled Privacy Extensions [93841.359894] lo: Disabled Privacy Extensions [93841.794537] lo: Disabled Privacy Extensions [93842.159782] lo: Disabled Privacy Extensions [93842.646683] lo: Disabled Privacy Extensions [93846.734029] lo: Disabled Privacy Extensions [93847.168099] lo: Disabled Privacy Extensions [93847.390690] lo: Disabled Privacy Extensions [93847.817685] lo: Disabled Privacy Extensions [93849.140450] lo: Disabled Privacy Extensions [93849.634822] lo: Disabled Privacy Extensions [93850.392108] lo: Disabled Privacy Extensions [93850.975057] lo: Disabled Privacy Extensions [93851.432387] lo: Disabled Privacy Extensions [93851.976379] lo: Disabled Privacy Extensions [93852.437472] lo: Disabled Privacy Extensions [93853.143600] lo: Disabled Privacy Extensions [93853.596349] lo: Disabled Privacy Extensions [93854.148058] lo: Disabled Privacy Extensions [93854.600426] lo: Disabled Privacy Extensions [93855.141618] lo: Disabled Privacy Extensions [93855.596434] lo: Disabled Privacy Extensions [93856.145245] lo: Disabled Privacy Extensions [93856.600384] lo: Disabled Privacy Extensions [93857.150800] lo: Disabled Privacy Extensions [93857.604543] lo: Disabled Privacy Extensions [93858.177059] lo: Disabled Privacy Extensions [93858.632301] lo: Disabled Privacy Extensions [93859.182024] lo: Disabled Privacy Extensions [93859.632327] lo: Disabled Privacy Extensions [93860.181446] lo: Disabled Privacy Extensions [93860.631587] lo: Disabled Privacy Extensions [93861.182029] lo: Disabled Privacy Extensions [93861.634095] lo: Disabled Privacy Extensions [93862.184725] lo: Disabled Privacy Extensions [144266.195058] lo: Disabled Privacy Extensions ** Model information not available ** Loaded modules: Module Size Used by nfsd 192383 13 exportfs 2586 1 nfsd nfs 205624 0 lockd 49301 2 nfsd,nfs fscache 24422 1 nfs nfs_acl 1695 2 nfsd,nfs auth_rpcgss 25068 2 nfsd,nfs sunrpc 134156 12 nfsd,nfs,lockd,nfs_acl,auth_rpcgss loop 9721 0 stv0299 6600 1 ves1x93 4129 0 dvb_ttpci 70010 17 dvb_core 63638 2 stv0299,dvb_ttpci snd_pcsp 5219 0 saa7146_vv 31914 1 dvb_ttpci snd_pcm 47350 1 snd_pcsp videodev 25445 1 saa7146_vv v4l1_compat 10250 1 videodev snd_timer 12258 1 snd_pcm saa7146 10007 2 dvb_ttpci,saa7146_vv snd 33551 3 snd_pcsp,snd_pcm,snd_timer videobuf_dma_sg 7099 1 saa7146_vv soundcore 3450 1 snd videobuf_core 10440 2 saa7146_vv,videobuf_dma_sg shpchp 21220 0 parport_pc 15799 0 joydev 6771 0 ttpci_eeprom 1224 1 dvb_ttpci snd_page_alloc 4977 1 snd_pcm i2c_viapro 4419 0 serio_raw 2916 0 parport 22554 1 parport_pc processor 25803 1 evdev 5609 3 pci_hotplug 18065 1 shpchp i2c_core 12612 6 stv0299,ves1x93,dvb_ttpci,videodev,ttpci_eeprom,i2c_viapro ext4 254301 2 mbcache 3762 1 ext4 jbd2 55835 1 ext4 crc16 1027 1 ext4 raid1 16067 1 md_mod 67093 2 raid1 hid_cherry 1113 0 ide_gd_mod 17103 3 usbhid 26784 0 hid 50545 2 hid_cherry,usbhid sd_mod 25717 4 crc_t10dif 1012 1 sd_mod ide_pci_generic 1924 0 uhci_hcd 15953 0 ata_generic 2015 0 ehci_hcd 27230 0 sata_via 5441 4 via82cxxx 4390 2 libata 113728 2 ata_generic,sata_via usbcore 97930 4 usbhid,uhci_hcd,ehci_hcd ide_core 63850 3 ide_gd_mod,ide_pci_generic,via82cxxx nls_base 4541 1 usbcore scsi_mod 101073 2 sd_mod,libata button 3598 0 via_agp 4608 1 r8169 24568 0 mii 2714 1 r8169 agpgart 19516 1 via_agp thermal 9206 0 fan 2586 0 thermal_sys 9378 3 processor,thermal,fan ** PCI devices: 00:00.0 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:0314] Subsystem: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:0314] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 8 Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M] Capabilities: [80] AGP version 3.5 Status: RQ=8 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: agpgart-via 00:00.1 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:1314] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:00.2 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:2314] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:00.3 Host bridge [0600]: VIA Technologies, Inc. PT890 Host Bridge [1106:3208] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:00.4 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:4314] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:00.7 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:7314] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237/VX700 PCI Bridge [1106:b198] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fb000000-fcffffff Prefetchable memory behind bridge: f4000000-f7ffffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR+ <PERR+ BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 00:08.0 Multimedia controller [0480]: Philips Semiconductors SAA7146 [1131:7146] (rev 01) Subsystem: Technotrend Systemtechnik GmbH Technotrend/Hauppauge DVB card rev2.1 [13c2:0003] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (3750ns min, 9500ns max) Interrupt: pin A routed to IRQ 17 Region 0: Memory at fdfff000 (32-bit, non-prefetchable) [size=512] Kernel driver in use: dvb 00:09.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet [10ec:8167] (rev 10) Subsystem: Jetway Information Co., Ltd. Device [16f3:10ec] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at f000 [size=256] Region 1: Memory at fdffe000 (32-bit, non-prefetchable) [size=256] [virtual] Expansion ROM at 3c000000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: r8169 00:0b.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet [10ec:8167] (rev 10) Subsystem: Jetway Information Co., Ltd. Device [16f3:10ec] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 19 Region 0: I/O ports at f200 [size=256] Region 1: Memory at fdffd000 (32-bit, non-prefetchable) [size=256] [virtual] Expansion ROM at 3c020000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: r8169 00:0f.0 IDE interface [0101]: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller [1106:3149] (rev 80) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller [1106:3149] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin B routed to IRQ 20 Region 0: I/O ports at ff00 [size=8] Region 1: I/O ports at fe00 [size=4] Region 2: I/O ports at fd00 [size=8] Region 3: I/O ports at fc00 [size=4] Region 4: I/O ports at fb00 [size=16] Region 5: I/O ports at f400 [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: sata_via 00:0f.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE [1106:0571] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 20 Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] Region 4: I/O ports at fa00 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: VIA_IDE 00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 21 Region 4: I/O ports at f900 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd 00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 21 Region 4: I/O ports at f800 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd 00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at f700 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd 00:10.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at f600 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd 00:10.4 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 86) (prog-if 20 [EHCI]) Subsystem: VIA Technologies, Inc. USB 2.0 [1106:3104] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin C routed to IRQ 21 Region 0: Memory at fdffc000 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ehci_hcd 00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South] [1106:3227] Subsystem: VIA Technologies, Inc. DFI KT600-AL / Soltek SL-B9D-FGR Motherboard [1106:3227] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 01:00.0 VGA compatible controller [0300]: VIA Technologies, Inc. CN700/P4M800 Pro/P4M800 CE/VN800 [S3 UniChrome Pro] [1106:3344] (rev 01) (prog-if 00 [VGA controller]) Subsystem: VIA Technologies, Inc. CN700/P4M800 Pro/P4M800 CE/VN800 [S3 UniChrome Pro] [1106:3344] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (500ns min) Interrupt: pin A routed to IRQ 11 Region 0: Memory at f4000000 (32-bit, prefetchable) [size=64M] Region 1: Memory at fb000000 (32-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at fc000000 [disabled] [size=64K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] AGP version 3.0 Status: RQ=256 Iso- ArqSz=0 Cal=7 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none> ** USB devices: Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -- System Information: Debian Release: squeeze/sid APT prefers testing APT policy: (500, 'testing') Architecture: i386 (i686) Kernel: Linux 2.6.32-trunk-686 (SMP w/1 CPU core) Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-2.6.32-trunk-686 depends on: ii debconf [debconf-2.0] 1.5.28 Debian configuration management sy ii initramfs-tools [linux-initr 0.93.4 tools for generating an initramfs ii module-init-tools 3.12~pre1-1 tools for managing Linux kernel mo Versions of packages linux-image-2.6.32-trunk-686 recommends: ii firmware-linux-free 2.6.32-5 Binary firmware for various driver ii libc6-i686 2.10.2-6 GNU C Library: Shared libraries [i Versions of packages linux-image-2.6.32-trunk-686 suggests: pn grub | lilo <none> (no description available) pn linux-doc-2.6.32 <none> (no description available) Versions of packages linux-image-2.6.32-trunk-686 is related to: pn firmware-bnx2 <none> (no description available) pn firmware-bnx2x <none> (no description available) pn firmware-ipw2x00 <none> (no description available) pn firmware-ivtv <none> (no description available) pn firmware-iwlwifi <none> (no description available) pn firmware-linux <none> (no description available) pn firmware-linux-nonfree <none> (no description available) pn firmware-qlogic <none> (no description available) pn firmware-ralink <none> (no description available) -- debconf information: linux-image-2.6.32-trunk-686/prerm/would-invalidate-boot-loader-2.6.32-trunk-686: true linux-image-2.6.32-trunk-686/postinst/bootloader-test-error-2.6.32-trunk-686: shared/kernel-image/really-run-bootloader: true linux-image-2.6.32-trunk-686/postinst/depmod-error-initrd-2.6.32-trunk-686: false linux-image-2.6.32-trunk-686/prerm/removing-running-kernel-2.6.32-trunk-686: true linux-image-2.6.32-trunk-686/postinst/bootloader-error-2.6.32-trunk-686: * linux-image-2.6.32-trunk-686/postinst/missing-firmware-2.6.32-trunk-686: -- To UNSUBSCRIBE, email to [email protected] with a subject of "unsubscribe". Trouble? Contact [email protected]
