Package: installation-reports INSTALL REPORT
Debian-installer-version: 3.1 (sarge), obtained the image as a set of 14 CDS from linux-cd.com uname -a: Linux debian 2.4.27-2-386 #1 Mon May 16 16:47:51 JST 2005 i686 GNU/Linux Date: Installed on September 4, 2005 Method: Configured BIOS to boot from a CD and ran the installer program from disc 1 Machine: Dell Inspiron 9300 (laptop) Processor: Pentium M 730 (1.60 Ghz) Memory: 512MB RAM at 533 Mhz Root Device: unsure Root Size/partition table: Disk /dev/hda: 60.0 GB, 60011642880 bytes 255 heads, 63 sectors/track, 7296 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/hda1 1 6 48163+ de Dell Utility /dev/hda2 * 7 3654 29302560 7 HPFS/NTFS /dev/hda3 6893 7295 3237097+ db CP/M / CTOS / ... /dev/hda4 3655 6892 26009235 5 Extended /dev/hda5 * 3655 4505 6835626 83 Linux /dev/hda6 4506 4610 843381 82 Linux swap / Solaris /dev/hda7 4611 6892 18330133+ 83 Linux Partition table entries are not in disk order Output of lspci and lspci -n: (from lspci) 0000:00:00.0 Host bridge: Intel Corp. Mobile Memory Controller Hub (rev 03) 0000:00:01.0 PCI bridge: Intel Corp. Mobile Memory Controller Hub PCI Express Port (rev 03) 0000:00:1d.0 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) 0000:00:1d.1 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) 0000:00:1d.2 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) 0000:00:1d.3 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) 0000:00:1d.7 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) 0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev d3) 0000:00:1e.2 Multimedia audio controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03) 0000:00:1e.3 Modem: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 03) 0000:00:1f.0 ISA bridge: Intel Corp. 82801FBM (ICH6M) LPC Interface Bridge (rev 03) 0000:00:1f.2 IDE interface: Intel Corp. 82801FBM (ICH6M) SATA Controller (rev 03) 0000:00:1f.3 SMBus: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03) 0000:01:00.0 VGA compatible controller: nVidia Corporation: Unknown device 00c8 (rev a2) 0000:03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) 0000:03:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b3) 0000:03:01.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 08) 0000:03:01.2 0805: Ricoh Co Ltd: Unknown device 0822 (rev 17) 0000:03:03.0 Network controller: Intel Corp. PRO/Wireless 2200BG (rev 05) (from lspci -n) 0000:00:00.0 0600: 8086:2590 (rev 03) 0000:00:01.0 0604: 8086:2591 (rev 03) 0000:00:1d.0 0c03: 8086:2658 (rev 03) 0000:00:1d.1 0c03: 8086:2659 (rev 03) 0000:00:1d.2 0c03: 8086:265a (rev 03) 0000:00:1d.3 0c03: 8086:265b (rev 03) 0000:00:1d.7 0c03: 8086:265c (rev 03) 0000:00:1e.0 0604: 8086:2448 (rev d3) 0000:00:1e.2 0401: 8086:266e (rev 03) 0000:00:1e.3 0703: 8086:266d (rev 03) 0000:00:1f.0 0601: 8086:2641 (rev 03) 0000:00:1f.2 0101: 8086:2653 (rev 03) 0000:00:1f.3 0c05: 8086:266a (rev 03) 0000:01:00.0 0300: 10de:00c8 (rev a2) 0000:03:00.0 0200: 14e4:170c (rev 02) 0000:03:01.0 0607: 1180:0476 (rev b3) 0000:03:01.1 0c00: 1180:0552 (rev 08) 0000:03:01.2 0805: 1180:0822 (rev 17) 0000:03:03.0 0280: 8086:4220 (rev 05) Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot worked: [O] Configure network HW: [O] Config network: [O] Detect CD: [O] Load installer modules: [O] Detect hard drives: [E] Partition hard drives: [O] Create file systems: [O] Mount partitions: [O] Install base system: [O] Install boot loader: [O] Reboot: [O] Comments/Problems: I have a dual boot set up using grub, with Debian Gnu/Linux 3.1 (sarge) and Windows XP Home Edition (which was pre-installed on my computer.) I first tried to install Debian using the 2.6 kernel and when I got to the partitioning phase, received a message saying that no partitionable media were found (that is, the installer could not identify my hard drive). But when I tried again using the 2.4 kernel, there was no problem with partitioning and the rest of the install went smoothly. -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]