I got following error message when I was going to load ARM7 program into target GBA (ARM7TDMI) board.
--- Source file = /home/jingba/my_OS/build/bin/sagos2.bin Program size = 14690 Error: OPTIMIZE GBA-USB-bootcable is not found! --- I have been using this loading program on Debian Lenny or Etch, and was able to load successfully. Is any change for USB devices after Squeeze? I attach dmesg that seems recognizing the USB. Thanks in advance for your help or information. ============== dmesg ================================================================ [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.32-5-686 (Debian 2.6.32-43) ([email protected]) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Sat Mar 31 03:56:41 UTC 2012 [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] NSC Geode by NSC [ 0.000000] Cyrix CyrixInstead [ 0.000000] Centaur CentaurHauls [ 0.000000] Transmeta GenuineTMx86 [ 0.000000] Transmeta TransmetaCPU [ 0.000000] UMC UMC UMC UMC [ 0.000000] BIOS-provided physical RAM map: ... [ 2.240196] scsi 2:0:0:0: Direct-Access ATA HITACHI HTS54161 SBDI PQ: 0 ANSI: 5 [ 2.254967] sd 2:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB) [ 2.255050] sd 2:0:0:0: [sda] Write Protect is off [ 2.255054] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.255090] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.255315] sda: [ 2.393023] usb 4-1: new full speed USB device using uhci_hcd and address 2 [ 2.554100] usb 4-1: New USB device found, idVendor=0bfe, idProduct=3000 [ 2.554105] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.554109] usb 4-1: Product: GBA BOOT CABLE USB <<<<< here [ 2.554113] usb 4-1: Manufacturer: OPTIMIZE PRODUCTS <<<<< here [ 2.554215] usb 4-1: configuration #1 chosen from 1 choice [ 2.671619] sda1 sda2 sda3 sda4 [ 2.698464] sd 2:0:0:0: [sda] Attached SCSI disk [ 2.796038] usb 2-1: new full speed USB device using uhci_hcd and address 2 [ 2.967515] usb 2-1: New USB device found, idVendor=0a5c, idProduct=2110 [ 2.967520] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.967525] usb 2-1: Product: BCM2045B [ 2.967528] usb 2-1: Manufacturer: Broadcom Corp [ 2.967632] usb 2-1: configuration #1 chosen from 1 choice [ 3.208037] usb 2-2: new full speed USB device using uhci_hcd and address 3 [ 3.296699] PM: Starting manual resume from disk ... [ 22.477584] padlock: VIA PadLock not detected. ... [ 2603.673151] usb 4-1: USB disconnect, address 2 [ 2604.904113] usb 4-1: new full speed USB device using uhci_hcd and address 3 [ 2605.057472] usb 4-1: New USB device found, idVendor=0bfe, idProduct=3000 [ 2605.057479] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2605.057485] usb 4-1: Product: GBA BOOT CABLE USB <<<<< here [ 2605.057490] usb 4-1: Manufacturer: OPTIMIZE PRODUCTS <<<<< here [ 2605.057654] usb 4-1: configuration #1 chosen from 1 choice -- To UNSUBSCRIBE, email to [email protected] with a subject of "unsubscribe". Trouble? Contact [email protected] Archive: http://lists.debian.org/[email protected]
