On Thu, Oct 18, 2007 at 02:41:54PM -0600, Matthew Wilcox wrote: > On Thu, Oct 18, 2007 at 09:31:52PM +0100, Jo Mills wrote: > > Today, I came back from work, ssh into B2000 from my Sparc to find FS > > was in read-only mode. Syslog just seems to have gone for a walk part > > way through logging. OK, re-boot. Comes up fine, I configured > > exim4-light, did a test e-mail, started to install logcheck and > > wallop, FS goes read-only again. > > What does 'dmesg' tell you happened? >
Hi Matthew, The whole dmesg output is some 530 lines, I can send it all if you want but I think the salient parts are shown below. Is it as straight forward as a duff disk? Regards, Jo. green:~# dmesg Linux version 2.6.18-5-parisc (Debian 2.6.18.dfsg.1-13etch4) ([EMAIL PROTECTED]) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 Tue Oct 2 23:19:18 UTC 2007 FP[0] enabled: Rev 1 Model 16 The 32-bit Kernel has started... Initialized PDC Console for debugging. Determining PDC firmware type: System Map. model 00005d00 00000481 00000000 00000002 777ee59f 100000f0 00000008 000000b2 000000b2 vers 00000301 CPUID vers 17 rev 11 (0x0000022b) capabilities 0x3 model 9000/785/B2000 Total Memory: 1024 MB initrd: 4fb7d000-4ffee8cc initrd: reserving 3fb7d000-3ffee8cc (mem_max 40000000) . . . hda: LITE-ON CD-RW SOHR-5239V, ATAPI CD/DVD-ROM drive ide0 at 0xe00-0xe07,0xd02 on irq 7 Probing IDE interface ide1... sym0: <895a> rev 0x1 at pci 0000:00:0f.0 irq 68 sym0: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking sym0: SCSI BUS has been reset. scsi0 : sym-2.2.3 hda: ATAPI 52X CD-ROM CD-R/RW drive, 1536kB Cache Uniform CD-ROM driver Revision: 3.20 Vendor: SEAGATE Model: ST39103LC Rev: HP00 Type: Direct-Access ANSI SCSI revision: 02 target0:0:0: tagged command queuing enabled, command queue depth 16. target0:0:0: Beginning Domain Validation target0:0:0: asynchronous target0:0:0: wide asynchronous target0:0:0: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15) target0:0:0: Domain Validation skipping write tests target0:0:0: Ending Domain Validation Vendor: SEAGATE Model: ST39102LC Rev: HP01 Type: Direct-Access ANSI SCSI revision: 02 target0:0:6: tagged command queuing enabled, command queue depth 16. target0:0:6: Beginning Domain Validation target0:0:6: asynchronous target0:0:6: wide asynchronous target0:0:6: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15) target0:0:6: Domain Validation skipping write tests target0:0:6: Ending Domain Validation ohci_hcd 0000:00:0e.2: OHCI Host Controller ohci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:0e.2: created debug files . . . SCSI device sda: 17773524 512-byte hdwr sectors (9100 MB) sda: Write Protect is off sda: Mode Sense: 9f 00 10 08 hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000 ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s SCSI device sda: drive cache: write through w/ FUA SCSI device sda: 17773524 512-byte hdwr sectors (9100 MB) sda: Write Protect is off sda: Mode Sense: 9f 00 10 08 SCSI device sda: drive cache: write through w/ FUA sda: sda1 sda2 sda3 < sda5 sda6 > sd 0:0:0:0: Attached scsi disk sda SCSI device sdb: 17773524 512-byte hdwr sectors (9100 MB) sdb: Write Protect is off sdb: Mode Sense: 9f 00 10 08 SCSI device sdb: drive cache: write through w/ FUA SCSI device sdb: 17773524 512-byte hdwr sectors (9100 MB) sdb: Write Protect is off sdb: Mode Sense: 9f 00 10 08 hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301 SCSI device sdb: drive cache: write through w/ FUA sdb: sdb1 sd 0:0:6:0: Attached scsi disk sdb ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS . . . usb 1-2:1.1: uevent Adding 385520k swap on /dev/sda6. Priority:-1 extents:1 across:385520k sd 0:0:0:0: SCSI error: return code = 0x000100ff end_request: I/O error, dev sda, sector 329579 Buffer I/O error on device sda5, logical block 1027 lost page write due to I/O error on sda5 sd 0:0:0:0: ABORT operation started. sym0: SCSI BUS reset detected. sym0: SCSI BUS has been reset. sd 0:0:0:0: ABORT operation complete. sd 0:0:0:0: ABORT operation started. sd 0:0:0:0: ABORT operation failed. sd 0:0:0:0: DEVICE RESET operation started. sd 0:0:0:0: DEVICE RESET operation complete. target0:0:0: control msgout: c. sym0: TARGET 0 has been reset. target0:0:0: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15) EXT3 FS on sda5, internal journal loop: loaded (max 8 devices) device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: [EMAIL PROTECTED] kjournald starting. Commit interval 5 seconds EXT3 FS on sdb1, internal journal EXT3-fs: mounted filesystem with ordered data mode. eth0: Setting full-duplex based on MII#1 link partner capability of 45e1. . . . NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver eth0: no IPv6 routers present sd 0:0:0:0: SCSI error: return code = 0x000100ff end_request: I/O error, dev sda, sector 8859139 Buffer I/O error on device sda5, logical block 1067222 lost page write due to I/O error on sda5 . . . Buffer I/O error on device sda5, logical block 1067229 lost page write due to I/O error on sda5 sd 0:0:0:0: SCSI error: return code = 0x000100ff end_request: I/O error, dev sda, sector 8859323 Buffer I/O error on device sda5, logical block 1067245 lost page write due to I/O error on sda5 Buffer I/O error on device sda5, logical block 1067246 lost page write due to I/O error on sda5 sd 0:0:0:0: SCSI error: return code = 0x000100ff end_request: I/O error, dev sda, sector 8859355 sd 0:0:0:0: SCSI error: return code = 0x000100ff . . . < 200 or so lines of much the same > . . . end_request: I/O error, dev sda, sector 8709971 sd 0:0:0:0: ABORT operation started. sym0: SCSI BUS reset detected. sym0: SCSI BUS has been reset. sd 0:0:0:0: ABORT operation complete. sd 0:0:0:0: ABORT operation started. sd 0:0:0:0: ABORT operation failed. sd 0:0:0:0: DEVICE RESET operation started. sd 0:0:0:0: DEVICE RESET operation complete. target0:0:0: control msgout: c. sym0: TARGET 0 has been reset. target0:0:0: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15) sd 0:0:0:0: ABORT operation started. sym0: SCSI BUS reset detected. sym0: SCSI BUS has been reset. sd 0:0:0:0: ABORT operation complete. sd 0:0:0:0: ABORT operation started. sd 0:0:0:0: ABORT operation failed. sd 0:0:0:0: DEVICE RESET operation started. sd 0:0:0:0: DEVICE RESET operation complete. target0:0:0: control msgout: c. sym0: TARGET 0 has been reset. target0:0:0: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15) green:~# -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
