Alle ago 30 at 06:58, /dev/null scrisse:
>> Timing buffered disk reads: 64 MB in 5.28 seconds = 12.12 MB/sec
>> Timing buffer-cache reads: 128 MB in 1.03 seconds =124.27 MB/sec
>Va piu` o meno come l'IBM ThinkPad A20m che avevo fino a un mese fa.
>Anche quello aveva circa 2 anni.
Spinto dalla curiosit� ho provato anch'io, ma i miei risultati, mi
sembrano un po' deludenti :(
hdparm -i /dev/hda
/dev/hda:
Model=IBM-DJSA-210, FwRev=JS2OABCA, SerialNo=9ZQ9Z5M7925
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=384kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=19640880
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4
AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5
hdparm -I /dev/hda
/dev/hda:
non-removable ATA device, with non-removable media
Model Number: IBM-DJSA-210
Serial Number: 9ZQ9Z5M7925
Firmware Revision: JS2OABCA
Standards:
Used: ATA/ATAPI-5 T13 1321D revision 1
Supported: 2 3 4 5
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
bytes/track: 0 (obsolete)
bytes/sector: 0 (obsolete)
current sector capacity: 16514064
LBA user addressable sectors = 19640880
Capabilities:
LBA, IORDY(can be disabled)
Buffer size: 384.0kB ECC bytes: 4 Queue depth: 1
Standby timer values: spec'd by Vendor, no device specific minimum
r/w multiple sector transfer: Max = 16 Current = 16
Advanced power management level: 16512
DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* look-ahead
* write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
SET MAX security extension
Address offset used (large drive)
Power-Up In Standby feature set
* Advanced Power Management feature set
Security:
Master password revision code = xxxxx (c'era un numero che ho
cancellato per sicurezza :) )
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
16min for SECURITY ERASE UNIT.
HW reset results:
CBLID- above Vih
Device num = 0 determined by the jumper
Checksum: correct
/dev/hda:
Timing buffered disk reads: 64 MB in 3.95 seconds = 16.20 MB/sec
/dev/hda:
Timing buffer-cache reads: 128 MB in 2.11 seconds = 60.66 MB/sec
Questo dopo aver dato il comando:
hdparm -d1 -W1 -A1 -X69 -u1 -c3 -m16 /dev/hda
Confrontando i miei risultati con quello dei vostri portatili, il
secondo risultato � dimezzato.
Ci sono altri parametri che posso abilitare in sicurezza?
Inoltre, quella sezione finale "Security:" con la password e tutti gli
altri parametri, a che serve e come si abilita? Dove si trovano info a
riguardo?
--
Fabio
