Your message dated Sat, 23 Apr 2016 21:50:43 +0200
with message-id <20160423195043.GA5142@feivel>
and subject line Works again with 4.5.1-1-amd64
has caused the Debian Bug report #820127,
regarding BCM4401-B0 fails to work under kernel 4.4.0 and newer
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact [email protected]
immediately.)


-- 
820127: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=820127
Debian Bug Tracking System
Contact [email protected] with problems
--- Begin Message ---
Package: src:linux
Version: 4.4.6-1
Severity: important

Linux is successfully runnin gon this computer for ages, but since upgrading to
linux-image-4.4.0-1-amd64 network does not work anymore. The same holds for the
linux-image-4.5.0-trunk-amd64 package from experimental. I had to go back to
4.3.0.

Anyhow, the error is kind of cryptic. The device is seen and can be configured,
but not fired. Here's a try:

michael@machine:~$ LC_ALL=C sudo ip link set eth0 up 
RTNETLINK answers: Cannot allocate memory
michael@machine:~$ LC_ALL=C sudo ifconfig eth0 192.168.0.8 up
SIOCSIFFLAGS: Cannot allocate memory
SIOCSIFFLAGS: Cannot allocate memory

That's it, nothing in the logs. Any idea what this could be?

Michael

-- Package-specific info:
** Kernel log: boot messages should be attached

** Model information
sys_vendor: Dell Inc
product_name: Dimension E521
product_version:  
chassis_vendor: Dell Inc
chassis_version:  
bios_vendor: Dell Inc
bios_version: 1.1.11
board_vendor: Dell Inc
board_name: 0CT103
board_version: A03

** Network interface configuration:

auto lo
iface lo inet loopback



** PCI devices:
00:00.0 RAM memory [0500]: NVIDIA Corporation C51 Host Bridge [10de:02f0] (rev 
a2)
        Subsystem: NVIDIA Corporation C51 Host Bridge [10de:02f0]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: <access denied>

00:00.1 RAM memory [0500]: NVIDIA Corporation C51 Memory Controller 0 
[10de:02fa] (rev a2)
        Subsystem: NVIDIA Corporation C51 Memory Controller 0 [10de:02fa]
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-

00:00.2 RAM memory [0500]: NVIDIA Corporation C51 Memory Controller 1 
[10de:02fe] (rev a2)
        Subsystem: NVIDIA Corporation C51 Memory Controller 1 [10de:02fe]
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-

00:00.3 RAM memory [0500]: NVIDIA Corporation C51 Memory Controller 5 
[10de:02f8] (rev a2)
        Subsystem: NVIDIA Corporation C51 Memory Controller 5 [10de:02f8]
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-

00:00.4 RAM memory [0500]: NVIDIA Corporation C51 Memory Controller 4 
[10de:02f9] (rev a2)
        Subsystem: NVIDIA Corporation C51 Memory Controller 4 [10de:02f9]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0

00:00.5 RAM memory [0500]: NVIDIA Corporation C51 Host Bridge [10de:02ff] (rev 
a2)
        Subsystem: NVIDIA Corporation C51 Host Bridge [10de:02ff]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: <access denied>

00:00.6 RAM memory [0500]: NVIDIA Corporation C51 Memory Controller 3 
[10de:027f] (rev a2)
        Subsystem: NVIDIA Corporation C51 Memory Controller 3 [10de:027f]
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-

00:00.7 RAM memory [0500]: NVIDIA Corporation C51 Memory Controller 2 
[10de:027e] (rev a2)
        Subsystem: NVIDIA Corporation C51 Memory Controller 2 [10de:027e]
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-

00:02.0 PCI bridge [0604]: NVIDIA Corporation C51 PCI Express Bridge 
[10de:02fc] (rev a1) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin ? routed to IRQ 24
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 0000a000-0000afff
        Memory behind bridge: fda00000-fdafffff
        Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: <access denied>
        Kernel driver in use: pcieport
        Kernel modules: shpchp

00:03.0 PCI bridge [0604]: NVIDIA Corporation C51 PCI Express Bridge 
[10de:02fd] (rev a1) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin ? routed to IRQ 25
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
        I/O behind bridge: 00008000-00008fff
        Memory behind bridge: fd800000-fd8fffff
        Prefetchable memory behind bridge: 00000000fde00000-00000000fdefffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: <access denied>
        Kernel driver in use: pcieport
        Kernel modules: shpchp

00:04.0 PCI bridge [0604]: NVIDIA Corporation C51 PCI Express Bridge 
[10de:02fb] (rev a1) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin ? routed to IRQ 26
        Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
        I/O behind bridge: 0000b000-0000bfff
        Memory behind bridge: fdd00000-fddfffff
        Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: <access denied>
        Kernel driver in use: pcieport
        Kernel modules: shpchp

00:09.0 RAM memory [0500]: NVIDIA Corporation MCP51 Host Bridge [10de:0270] 
(rev a2)
        Subsystem: NVIDIA Corporation MCP51 Host Bridge [10de:cb84]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: <access denied>

00:0a.0 ISA bridge [0601]: NVIDIA Corporation MCP51 LPC Bridge [10de:0260] (rev 
a3)
        Subsystem: Dell MCP51 LPC Bridge [1028:01ed]
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0

00:0a.1 SMBus [0c05]: NVIDIA Corporation MCP51 SMBus [10de:0264] (rev a3)
        Subsystem: Dell MCP51 SMBus [1028:01ed]
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Interrupt: pin A routed to IRQ 23
        Region 4: I/O ports at 1c00 [size=64]
        Region 5: I/O ports at 1c40 [size=64]
        Capabilities: <access denied>
        Kernel driver in use: nForce2_smbus
        Kernel modules: i2c_nforce2, nv_tco

00:0a.2 RAM memory [0500]: NVIDIA Corporation MCP51 Memory Controller 0 
[10de:0272] (rev a3)
        Subsystem: Dell MCP51 Memory Controller 0 [1028:01ed]
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-

00:0b.0 USB controller [0c03]: NVIDIA Corporation MCP51 USB Controller 
[10de:026d] (rev a3) (prog-if 10 [OHCI])
        Subsystem: Dell MCP51 USB Controller [1028:01ed]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin A routed to IRQ 22
        Region 0: Memory at fe02f000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
        Kernel driver in use: ohci-pci
        Kernel modules: ohci_pci

00:0b.1 USB controller [0c03]: NVIDIA Corporation MCP51 USB Controller 
[10de:026e] (rev a3) (prog-if 20 [EHCI])
        Subsystem: Dell MCP51 USB Controller [1028:01ed]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin B routed to IRQ 21
        Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=256]
        Capabilities: <access denied>
        Kernel driver in use: ehci-pci
        Kernel modules: ehci_pci

00:0e.0 IDE interface [0101]: NVIDIA Corporation MCP51 Serial ATA Controller 
[10de:0266] (rev a1) (prog-if 85 [Master SecO PriO])
        Subsystem: Dell MCP51 Serial ATA Controller [1028:01ed]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin A routed to IRQ 20
        Region 0: I/O ports at 09f0 [size=8]
        Region 1: I/O ports at 0bf0 [size=4]
        Region 2: I/O ports at 0970 [size=8]
        Region 3: I/O ports at 0b70 [size=4]
        Region 4: I/O ports at e000 [size=16]
        Region 5: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
        Kernel driver in use: sata_nv
        Kernel modules: sata_nv, ata_generic

00:0f.0 IDE interface [0101]: NVIDIA Corporation MCP51 Serial ATA Controller 
[10de:0267] (rev a1) (prog-if 85 [Master SecO PriO])
        Subsystem: Dell MCP51 Serial ATA Controller [1028:01ed]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin A routed to IRQ 23
        Region 0: I/O ports at 09e0 [size=8]
        Region 1: I/O ports at 0be0 [size=4]
        Region 2: I/O ports at 0960 [size=8]
        Region 3: I/O ports at 0b60 [size=4]
        Region 4: I/O ports at cc00 [size=16]
        Region 5: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
        Kernel driver in use: sata_nv
        Kernel modules: sata_nv, ata_generic

00:10.0 PCI bridge [0604]: NVIDIA Corporation MCP51 PCI Bridge [10de:026f] (rev 
a2) (prog-if 01 [Subtractive decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
        I/O behind bridge: 00009000-00009fff
        Memory behind bridge: fdc00000-fdcfffff
        Prefetchable memory behind bridge: fdb00000-fdbfffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
        Capabilities: <access denied>

00:10.1 Audio device [0403]: NVIDIA Corporation MCP51 High Definition Audio 
[10de:026c] (rev a2)
        Subsystem: Dell MCP51 High Definition Audio [1028:01ed]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0 (500ns min, 1250ns max)
        Interrupt: pin B routed to IRQ 22
        Region 0: Memory at fe024000 (32-bit, non-prefetchable) [size=16K]
        Capabilities: <access denied>
        Kernel driver in use: snd_hda_intel
        Kernel modules: snd_hda_intel

00:18.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] K8 
[Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Capabilities: <access denied>

00:18.1 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] K8 
[Athlon64/Opteron] Address Map [1022:1101]
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-

00:18.2 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] K8 
[Athlon64/Opteron] DRAM Controller [1022:1102]
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Kernel modules: amd64_edac_mod

00:18.3 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] K8 
[Athlon64/Opteron] Miscellaneous Control [1022:1103]
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Capabilities: <access denied>
        Kernel driver in use: k8temp
        Kernel modules: k8temp

03:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. 
[AMD/ATI] RV730 PRO [Radeon HD 4650] [1002:9498] (prog-if 00 [VGA controller])
        Subsystem: Hightech Information System Ltd. RV730 PRO [Radeon HD 4650] 
[1787:2269]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 28
        Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
        Region 2: Memory at fdde0000 (64-bit, non-prefetchable) [size=64K]
        Region 4: I/O ports at bc00 [size=256]
        [virtual] Expansion ROM at fdd00000 [disabled] [size=128K]
        Capabilities: <access denied>
        Kernel driver in use: radeon
        Kernel modules: radeon

03:00.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] RV710/730 
HDMI Audio [Radeon HD 4000 series] [1002:aa38]
        Subsystem: Hightech Information System Ltd. RV710/730 HDMI Audio 
[Radeon HD 4000 series] [1787:aa38]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin B routed to IRQ 27
        Region 0: Memory at fddfc000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: <access denied>
        Kernel driver in use: snd_hda_intel
        Kernel modules: snd_hda_intel

04:07.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX 
[14e4:170c] (rev 02)
        Subsystem: Dell BCM4401-B0 100Base-TX [1028:01ed]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 64
        Interrupt: pin A routed to IRQ 19
        Region 0: Memory at fdcfe000 (32-bit, non-prefetchable) [size=8K]
        Capabilities: <access denied>
        Kernel driver in use: b44
        Kernel modules: b44


** USB devices:
Bus 001 Device 004: ID 046d:0990 Logitech, Inc. QuickCam Pro 9000
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 003: ID 046d:c03e Logitech, Inc. Premium Optical Wheel Mouse 
(M-BT58)
Bus 002 Device 002: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub


-- System Information:
Debian Release: stretch/sid
  APT prefers testing
  APT policy: (500, 'testing'), (500, 'stable'), (1, 'experimental')
Architecture: amd64 (x86_64)
Foreign Architectures: i386

Kernel: Linux 4.3.0-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)

Versions of packages linux-image-4.4.0-1-amd64 depends on:
ii  debconf [debconf-2.0]                   1.5.59
ii  initramfs-tools [linux-initramfs-tool]  0.123
ii  kmod                                    22-1
ii  linux-base                              4.0

Versions of packages linux-image-4.4.0-1-amd64 recommends:
ii  firmware-linux-free  3.4
ii  irqbalance           1.1.0-2

Versions of packages linux-image-4.4.0-1-amd64 suggests:
pn  debian-kernel-handbook  <none>
ii  grub-pc                 2.02~beta2-36
pn  linux-doc-4.4           <none>

Versions of packages linux-image-4.4.0-1-amd64 is related to:
pn  firmware-atheros                         <none>
pn  firmware-bnx2                            <none>
pn  firmware-bnx2x                           <none>
pn  firmware-brcm80211                       <none>
pn  firmware-intelwimax                      <none>
pn  firmware-ipw2x00                         <none>
pn  firmware-ivtv                            <none>
pn  firmware-iwlwifi                         <none>
pn  firmware-libertas                        <none>
pn  firmware-linux                           <none>
ii  firmware-linux-nonfree                   20160110-1
ii  firmware-misc-nonfree [firmware-ralink]  20160110-1
pn  firmware-myricom                         <none>
pn  firmware-netxen                          <none>
pn  firmware-qlogic                          <none>
pn  firmware-realtek                         <none>
pn  xen-hypervisor                           <none>

-- debconf information excluded

--- End Message ---
--- Begin Message ---
Although I cannot pinpoint the patch that did it, it magically works again, at 
least for now.

Michael
-- 
Michael Meskes
Michael at Fam-Meskes dot De, Michael at Meskes dot (De|Com|Net|Org)
Meskes at (Debian|Postgresql) dot Org
Jabber: michael at xmpp dot meskes dot org
VfL Borussia! Força Barça! Go SF 49ers! Use Debian GNU/Linux, PostgreSQL

--- End Message ---

Reply via email to