Package: src:linux Version: 4.9.16-1 Severity: important Dear Maintainer,
I have just upgraded from kernel on testing (4.9.13) to the version on unstable just to test it, the version on testing was running fine. The machine is running testing and is fully up to date with it. I had not noticed any problem till now. What I saw after upgrading to 4.9.16 and rebooting was that X came up in a low resolution mode, not 1920x1080 like it used to. The keyboard and mouse (both usb) were stuck, while the machine was still alive through network, so I assume that X were stuck at that time. The information that comes here is the one gathered booting in rescue mode. I'll try to add the X log and more info in a later mail. Regards. -- Package-specific info: ** Version: Linux version 4.9.0-2-amd64 ([email protected]) (gcc version 6.3.0 20170321 (Debian 6.3.0-10) ) #1 SMP Debian 4.9.16-1 (2017-03-22) ** Command line: BOOT_IMAGE=/boot/vmlinuz-4.9.0-2-amd64 root=UUID=e9f30b2f-d5d3-42f7-ae36-7231d931b2cd ro single ipv6.disable=1 ** Tainted: E (8192) * Unsigned module has been loaded. ** Kernel log: [ 1.960413] usb 2-1: New USB device found, idVendor=8087, idProduct=0024 [ 1.960491] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.960853] hub 2-1:1.0: USB hub found [ 1.961027] hub 2-1:1.0: 8 ports detected [ 1.966829] sdb: sdb1 sdb2 sdb3 [ 1.967472] sd 2:0:0:0: [sdb] Attached SCSI disk [ 1.968099] sda: sda1 sda2 sda3 [ 1.968612] sd 1:0:0:0: [sda] Attached SCSI disk [ 2.000768] Alternate GPT is invalid, using primary GPT. [ 2.000866] sdc: sdc1 sdc2 [ 2.001547] sd 3:0:0:0: [sdc] Attached SCSI removable disk [ 2.080055] tsc: Refined TSC clocksource calibration: 3092.981 MHz [ 2.080148] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2c9561128a6, max_idle_ns: 440795295901 ns [ 2.104209] random: fast init done [ 2.199115] md: bind<sdb2> [ 2.200338] md: bind<sdb3> [ 2.201761] md: bind<sdb1> [ 2.203368] md: bind<sdc2> [ 2.204836] md: bind<sdc1> [ 2.205964] md: bind<sda3> [ 2.207874] md: raid1 personality registered for level 1 [ 2.208274] md/raid1:md3: active with 2 out of 2 mirrors [ 2.208456] created bitmap (2 pages) for device md3 [ 2.208690] md3: bitmap initialized from disk: read 1 pages, set 0 of 3469 bits [ 2.214647] md3: detected capacity change from 0 to 232734261248 [ 2.223448] md: bind<sda2> [ 2.224061] usb 1-1.2: new full-speed USB device number 3 using ehci-pci [ 2.225026] md/raid1:md2: active with 2 out of 2 mirrors [ 2.225128] md2: detected capacity change from 0 to 17163091968 [ 2.337854] usb 1-1.2: New USB device found, idVendor=076b, idProduct=3021 [ 2.337937] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.338009] usb 1-1.2: Product: Smart Card Reader USB [ 2.338077] usb 1-1.2: Manufacturer: OMNIKEY AG [ 2.359110] md: bind<sda1> [ 2.361414] md/raid1:md1: active with 2 out of 2 mirrors [ 2.361599] created bitmap (6 pages) for device md1 [ 2.361958] md1: bitmap initialized from disk: read 1 pages, set 0 of 11177 bits [ 2.379937] md1: detected capacity change from 0 to 750021050368 [ 2.416164] usb 1-1.3: new low-speed USB device number 4 using ehci-pci [ 2.526457] usb 1-1.3: New USB device found, idVendor=04b3, idProduct=310d [ 2.526532] usb 1-1.3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.530649] hidraw: raw HID events driver (C) Jiri Kosina [ 2.533481] usbcore: registered new interface driver usbhid [ 2.533556] usbhid: USB HID core driver [ 2.534937] input: HID 04b3:310d as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:04B3:310D.0001/input/input3 [ 2.535176] hid-generic 0003:04B3:310D.0001: input,hidraw0: USB HID v1.11 Mouse [HID 04b3:310d] on usb-0000:00:1a.0-1.3/input0 [ 2.608195] usb 1-1.4: new high-speed USB device number 5 using ehci-pci [ 2.621923] md: linear personality registered for level -1 [ 2.623561] md: multipath personality registered for level -4 [ 2.625178] md: raid0 personality registered for level 0 [ 2.696152] raid6: sse2x1 gen() 5657 MB/s [ 2.764158] raid6: sse2x1 xor() 5446 MB/s [ 2.832177] raid6: sse2x2 gen() 10277 MB/s [ 2.900187] raid6: sse2x2 xor() 7502 MB/s [ 2.968206] raid6: sse2x4 gen() 11989 MB/s [ 3.036216] raid6: sse2x4 xor() 8944 MB/s [ 3.036288] raid6: using algorithm sse2x4 gen() 11989 MB/s [ 3.036357] raid6: .... xor() 8944 MB/s, rmw enabled [ 3.036428] raid6: using ssse3x2 recovery algorithm [ 3.036722] xor: automatically using best checksumming function avx [ 3.036983] async_tx: api initialized (async) [ 3.038644] md: raid6 personality registered for level 6 [ 3.038706] md: raid5 personality registered for level 5 [ 3.038766] md: raid4 personality registered for level 4 [ 3.042563] md: raid10 personality registered for level 10 [ 3.046569] PM: Starting manual resume from disk [ 3.046629] PM: Hibernation image partition 9:2 present [ 3.046630] PM: Looking for hibernation image. [ 3.046800] PM: Image not found (code -22) [ 3.046801] PM: Hibernation image not present or could not be loaded. [ 3.104352] clocksource: Switched to clocksource tsc [ 3.138218] usb 1-1.4: New USB device found, idVendor=17ef, idProduct=7203 [ 3.138294] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.138372] usb 1-1.4: Product: U2-Ethernet [ 3.138436] usb 1-1.4: Manufacturer: DAEC [ 3.138504] usb 1-1.4: SerialNumber: 000000 [ 3.224267] usb 1-1.6: new low-speed USB device number 6 using ehci-pci [ 3.236862] EXT4-fs (md1): mounted filesystem with ordered data mode. Opts: (null) [ 3.343243] usb 1-1.6: New USB device found, idVendor=04b3, idProduct=3025 [ 3.343317] usb 1-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.343394] usb 1-1.6: Product: USB NetVista Full Width Keyboard. [ 3.343462] usb 1-1.6: Manufacturer: LITE-ON Technology [ 3.349412] input: LITE-ON Technology USB NetVista Full Width Keyboard. as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.6/1-1.6:1.0/0003:04B3:3025.0002/input/input4 [ 3.354396] random: crng init done [ 3.408549] hid-generic 0003:04B3:3025.0002: input,hidraw1: USB HID v1.10 Keyboard [LITE-ON Technology USB NetVista Full Width Keyboard.] on usb-0000:00:1a.0-1.6/input0 [ 4.196714] systemd[1]: Failed to insert module 'autofs4': No such file or directory [ 4.280050] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 4.280297] systemd[1]: Detected architecture x86-64. [ 4.325950] systemd[1]: Set hostname to <duo>. [ 5.273185] systemd[1]: Listening on Device-mapper event daemon FIFOs. [ 5.273844] systemd[1]: Listening on Journal Socket. [ 5.274546] systemd[1]: Created slice System Slice. [ 5.275673] systemd[1]: Mounting POSIX Message Queue File System... [ 5.276677] systemd[1]: Mounting Debug File System... [ 5.277775] systemd[1]: Mounting Huge Pages File System... [ 5.278286] systemd[1]: Listening on udev Control Socket. [ 6.070326] EXT4-fs (md1): re-mounted. Opts: errors=remount-ro [ 6.129027] systemd-journald[291]: Received request to flush runtime journal from PID 1 [ 7.579641] Adding 16760828k swap on /dev/md2. Priority:-1 extents:1 across:16760828k FS [ 7.902317] EXT4-fs (md3): mounted filesystem with ordered data mode. Opts: acl ** Model information sys_vendor: LENOVO product_name: 5048R91 product_version: ThinkCentre M81 chassis_vendor: To Be Filled By O.E.M. chassis_version: To Be Filled By O.E.M. bios_vendor: LENOVO bios_version: 9HKT43AUS board_vendor: LENOVO board_name: board_version: ** Loaded modules: raid10(E) raid456(E) async_raid6_recov(E) async_memcpy(E) async_pq(E) async_xor(E) async_tx(E) xor(E) raid6_pq(E) libcrc32c(E) raid0(E) multipath(E) linear(E) ext4(E) crc16(E) jbd2(E) crc32c_generic(E) fscrypto(E) ecb(E) hid_generic(E) glue_helper(E) lrw(E) gf128mul(E) ablk_helper(E) cryptd(E) aes_x86_64(E) mbcache(E) usbhid(E) hid(E) raid1(E) md_mod(E) sr_mod(E) cdrom(E) sd_mod(E) psmouse(E) i2c_i801(E) i2c_smbus(E) ahci(E) libahci(E) e1000(E) crc32c_intel(E) libata(E) ehci_pci(E) skge(E) ehci_hcd(E) scsi_mod(E) e1000e(E) ptp(E) usbcore(E) usb_common(E) pps_core(E) ** Network interface configuration: auto lo iface lo inet loopback auto br0 iface br0 inet static address 10.10.48.146 netmask 255.255.255.0 up /sbin/route add -net 10.0.0.0 netmask 255.0.0.0 gw 10.10.48.1 up /sbin/route add -net 10.10.0.0 netmask 255.255.0.0 gw 10.10.48.1 bridge_hw 44:37:e6:6b:e9:48 bridge_ports eth0 usbeth0 bridge_fd 0 bridge_stp off bridge_maxwait 0 gateway 10.10.48.1 iface br1 inet static address 192.168.2.1 netmask 255.255.255.0 bridge_ports eth1 bridge_stp on bridge_fd 2 bridge_maxage 6 bridge_maxwait 0 iface br2 inet static address 0.0.0.0 netmask 255.255.255.255 bridge_ports eth1 eth2 bridge_fd 0 bridge_stp off bridge_maxwait 0 iface wlan0 inet manual wpa-driver wext wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf down /usr/local/sbin/down_if iface wlan1 inet manual wpa-driver wext wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf down /usr/local/sbin/down_if iface wlan2 inet manual wpa-driver wext wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf down /usr/local/sbin/down_if iface monitorizar inet manual up pump -i wlan0 --no-dns --no-ntp --route-metric 54 up ifconfig wlan0:0 172.22.11.123 netmask 255.255.255.0 down pump -k down /usr/local/sbin/down_if iface default inet manual up pump -i wlan0 --no-dns --no-ntp --route-metric 54 down pump -k down /usr/local/sbin/down_if ** Network status: *** IP interfaces and addresses: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever 2: eth2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether 00:0a:5e:65:57:d6 brd ff:ff:ff:ff:ff:ff 3: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether 44:37:e6:6b:e9:48 brd ff:ff:ff:ff:ff:ff 4: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether 00:02:b3:c6:f1:29 brd ff:ff:ff:ff:ff:ff *** Device statistics: Inter-| Receive | Transmit face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed eth1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 eth2: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 lo: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 eth0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 *** Protocol statistics: Ip: Forwarding: 2 0 total packets received 0 forwarded 0 incoming packets discarded 0 incoming packets delivered 0 requests sent out 72 dropped because of missing route Icmp: 0 ICMP messages received 0 input ICMP message failed ICMP input histogram: 0 ICMP messages sent 0 ICMP messages failed ICMP output histogram: Tcp: 0 active connection openings 0 passive connection openings 0 failed connection attempts 0 connection resets received 0 connections established 0 segments received 0 segments sent out 0 segments retransmitted 0 bad segments received 0 resets sent Udp: 0 packets received 0 packets to unknown port received 0 packet receive errors 0 packets sent 0 receive buffer errors 0 send buffer errors UdpLite: TcpExt: 0 packet headers predicted IpExt: ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0100] (rev 09) Subsystem: Lenovo 2nd Generation Core Processor Family DRAM Controller [17aa:3077] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0101] (rev 09) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 24 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fe600000-fe6fffff Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [88] Subsystem: Lenovo Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [17aa:3077] Capabilities: [80] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0f00c Data: 4171 Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <256ns, L1 <4us ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #0, PowerLimit 75.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR+, OBFF Not Supported ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Capabilities: [140 v1] Root Complex Link Desc: PortNumber=02 ComponentID=01 EltType=Config Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB- LinkType=MemMapped LinkValid+ Addr: 00000000fed19000 Kernel driver in use: pcieport 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04) Subsystem: Lenovo 6 Series/C200 Series Chipset Family MEI Controller [17aa:3077] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0 Interrupt: pin A routed to IRQ 11 Region 0: Memory at fe72a000 (64-bit, non-prefetchable) [size=16] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 00:16.3 Serial controller [0700]: Intel Corporation 6 Series/C200 Series Chipset Family KT Controller [8086:1c3d] (rev 04) (prog-if 02 [16550]) Subsystem: Lenovo 6 Series/C200 Series Chipset Family KT Controller [17aa:3077] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 0: I/O ports at f0a0 [size=8] Region 1: Memory at fe729000 (32-bit, non-prefetchable) [size=4K] Capabilities: [c8] Power Management version 3 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: serial 00:19.0 Ethernet controller [0200]: Intel Corporation 82579LM Gigabit Network Connection [8086:1502] (rev 05) Subsystem: Lenovo 82579LM Gigabit Network Connection [17aa:3077] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 25 Region 0: Memory at fe700000 (32-bit, non-prefetchable) [size=128K] Region 1: Memory at fe728000 (32-bit, non-prefetchable) [size=4K] Region 2: I/O ports at f040 [size=32] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0f00c Data: 41a1 Capabilities: [e0] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: e1000e 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) (prog-if 20 [EHCI]) Subsystem: Lenovo 6 Series/C200 Series Chipset Family USB Enhanced Host Controller [17aa:3077] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at fe727000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: ehci-pci 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05) Subsystem: Lenovo 6 Series/C200 Series Chipset Family High Definition Audio Controller [17aa:3077] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at fe720000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress- VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=1 ArbSelect=Fixed TC/VC=22 Status: NegoPending- InProgress- Capabilities: [130 v1] Root Complex Link Desc: PortNumber=0f ComponentID=00 EltType=Config Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+ Addr: 00000000fed1c000 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 [EHCI]) Subsystem: Lenovo 6 Series/C200 Series Chipset Family USB Enhanced Host Controller [17aa:3077] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at fe726000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: ehci-pci 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a5) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fe500000-fe5fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Subsystem: Lenovo 82801 PCI Bridge [17aa:3077] 00:1f.0 ISA bridge [0601]: Intel Corporation Q65 Express Chipset Family LPC Controller [8086:1c4c] (rev 05) Subsystem: Lenovo Q65 Express Chipset Family LPC Controller [17aa:3077] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family SATA AHCI Controller [8086:1c02] (rev 05) (prog-if 01 [AHCI 1.0]) Subsystem: Lenovo 6 Series/C200 Series Chipset Family SATA AHCI Controller [17aa:3077] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 26 Region 0: I/O ports at f090 [size=8] Region 1: I/O ports at f080 [size=4] Region 2: I/O ports at f070 [size=8] Region 3: I/O ports at f060 [size=4] Region 4: I/O ports at f020 [size=32] Region 5: Memory at fe725000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0f00c Data: 41e1 Capabilities: [70] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004 Capabilities: [b0] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05) Subsystem: Lenovo 6 Series/C200 Series Chipset Family SMBus Controller [17aa:3077] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 18 Region 0: Memory at fe724000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at f000 [size=32] Kernel driver in use: i801_smbus 01:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] Cedar [Radeon HD 5000/6000/7350/8350 Series] [1002:68f9] (prog-if 00 [VGA controller]) Subsystem: Micro-Star International Co., Ltd. [MSI] Radeon HD 5450 [1462:2181] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 2: Memory at fe620000 (64-bit, non-prefetchable) [size=128K] Region 4: I/O ports at e000 [size=256] Expansion ROM at 000c0000 [disabled] [size=128K] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?> Capabilities: [150 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- 01:00.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] Cedar HDMI Audio [Radeon HD 5400/6300/7300 Series] [1002:aa68] Subsystem: Micro-Star International Co., Ltd. [MSI] Cedar HDMI Audio [Radeon HD 5400/6300/7300 Series] [1462:aa68] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 10 Region 0: Memory at fe640000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?> Capabilities: [150 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- 02:00.0 Ethernet controller [0200]: Intel Corporation 82544EI Gigabit Ethernet Controller (Copper) [8086:1008] (rev 02) Subsystem: Intel Corporation PRO/1000 XT Server Adapter [8086:1107] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (63750ns min), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 20 Region 0: Memory at fe560000 (32-bit, non-prefetchable) [size=128K] Region 1: Memory at fe540000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at d100 [size=32] Expansion ROM at fe520000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [e4] PCI-X non-bridge device Command: DPERE- ERO+ RBC=512 OST=1 Status: Dev=00:00.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz- Capabilities: [f0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: e1000 02:01.0 Ethernet controller [0200]: 3Com Corporation 3c940 10/100/1000Base-T [Marvell] [10b7:1700] (rev 10) Subsystem: 3Com Corporation 3C941 Gigabit LOM Ethernet Adapter [10b7:0020] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (5750ns min, 7750ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 21 Region 0: Memory at fe580000 (32-bit, non-prefetchable) [size=16K] Region 1: I/O ports at d000 [size=256] Expansion ROM at fe500000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [50] Vital Product Data Product Name: 3Com Gigabit NIC (3C2000) Read-only fields: [PN] Part number: 40-0778-000 [EC] Engineering changes: Rev. 1.2 [MN] Manufacture ID: 33 43 6f 6d [SN] Serial number: HZKQ6557D6 [CP] Extended capability: 01 10 cc 03 [RV] Reserved: checksum good, 41 byte(s) reserved Read/write fields: [MC] Unknown: 29 04 02 00 00 00 01 00 [RW] Read-write area: 110 byte(s) free End Kernel driver in use: skge ** USB devices: Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 006: ID 04b3:3025 IBM Corp. NetVista Full Width Keyboard Bus 001 Device 005: ID 17ef:7203 Lenovo Ethernet adapter [U2L 100P-Y1] Bus 001 Device 004: ID 04b3:310d IBM Corp. Bus 001 Device 003: ID 076b:3021 OmniKey AG CardMan 3121 Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -- System Information: Debian Release: 9.0 APT prefers testing APT policy: (990, 'testing'), (500, 'stable-updates'), (500, 'unstable'), (500, 'stable'), (500, 'oldstable') Architecture: amd64 (x86_64) Foreign Architectures: i386 Kernel: Linux 4.9.0-2-amd64 (SMP w/4 CPU cores) Locale: LANG=gl_ES.UTF-8, LC_CTYPE=gl_ES.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Init: systemd (via /run/systemd/system) Versions of packages linux-image-4.9.0-2-amd64-unsigned depends on: ii initramfs-tools [linux-initramfs-tool] 0.127 ii kmod 23-2 ii linux-base 4.5 Versions of packages linux-image-4.9.0-2-amd64-unsigned recommends: ii firmware-linux-free 3.4 ii irqbalance 1.1.0-2.3 Versions of packages linux-image-4.9.0-2-amd64-unsigned suggests: pn debian-kernel-handbook <none> ii grub-pc 2.02~beta3-5 pn linux-doc-4.9 <none> Versions of packages linux-image-4.9.0-2-amd64-unsigned is related to: ii firmware-amd-graphics 20161130-2 pn firmware-atheros <none> ii firmware-bnx2 20161130-2 ii firmware-bnx2x 20161130-2 pn firmware-brcm80211 <none> pn firmware-cavium <none> pn firmware-intel-sound <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> ii firmware-linux-nonfree 20161130-2 ii firmware-misc-nonfree 20161130-2 pn firmware-myricom <none> pn firmware-netxen <none> ii firmware-qlogic 20161130-2 ii firmware-realtek 20161130-2 pn firmware-samsung <none> pn firmware-siano <none> pn firmware-ti-connectivity <none> pn xen-hypervisor <none> -- no debconf information
