Your message dated Sun, 09 May 2021 05:49:00 -0700 (PDT) with message-id <[email protected]> and subject line Closing this bug (BTS maintenance for src:linux bugs) has caused the Debian Bug report #799226, regarding linux-image-4.1.0-2-amd64: Not able to mount LVM RAID1 file system at boot to be marked as done.
This means that you claim that the problem has been dealt with. If this is not the case it is now your responsibility to reopen the Bug report if necessary, and/or fix the problem forthwith. (NB: If you are a system administrator and have no idea what this message is talking about, this may indicate a serious mail system misconfiguration somewhere. Please contact [email protected] immediately.) -- 799226: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=799226 Debian Bug Tracking System Contact [email protected] with problems
--- Begin Message ---Package: src:linux Version: 4.1.6-1 Severity: normal Dear maintainer(s), I recently put one of my file systems on LVM RAID1. All is fine when I lvconvert or lvcreate the RAID1 mirror on a running kernel. The problem is when I reboot the system. The linux-image-4.1.0-1-amd64 is affected by the same problem. Rebooting with a linux-image-4.0.0-2-amd64 kernel works fine. The LVM RAID1 file system mounts automatically and is fully usable. During the linux-image-4.1.0-*-amd64 boots I see: Setting up LVM Volume Groups... lvmetad is not active yet, using direct activation during sysinit device-mapper: reload ioctl on (253:8) failed: Invalid argument and a little later: fsck.ext4: No such file or directory while trying to open /dev/mapper/helix-srv Possibly non-existent device? Trying to activate the LV after the boot does not work either. # lvchange -ay helix/srv device-mapper: reload iocth on (253:8) failed: Invalid argument In my syslog I see: mdX: invalid bitmap file superblock: bad magic mdX: bitmap file superblock magic: 00000401 and mdX: failed to create bitmap (-22) device-mapper: table: 253:8 raid: Fail to run raid araay I have found https://bugzilla.kernel.org/show_bug.cgi?id=100491[1] which mentions some of the messages I observe. I do not get the OOPS but it might be related. For the time being I'll stick to 4.0. -- Package-specific info: ** Version: Linux version 4.1.0-2-amd64 ([email protected]) (gcc version 4.9.3 (Debian 4.9.3-3) ) #1 SMP Debian 4.1.6-1 (2015-08-23) ** Command line: BOOT_IMAGE=/vmlinuz-4.1.0-2-amd64 root=/dev/mapper/helix-root ro quiet cgroup_enable=memory ** Tainted: I (2048) * Working around severe firmware bug. ** Kernel log: [ 5.923596] nouveau [ VBIOS][0000:0f:00.0] version 70.18.89.00.02 [ 5.924005] nouveau [ PMC][0000:0f:00.0] MSI interrupts enabled [ 5.924042] nouveau [ PFB][0000:0f:00.0] RAM type: DDR3 [ 5.924044] nouveau [ PFB][0000:0f:00.0] RAM size: 512 MiB [ 5.924045] nouveau [ PFB][0000:0f:00.0] ZCOMP: 960 tags [ 5.927663] nouveau [ VOLT][0000:0f:00.0] GPU voltage: 900000uv [ 5.948974] input: HP WMI hotkeys as /devices/virtual/input/input14 [ 5.955823] nouveau [ PTHERM][0000:0f:00.0] FAN control: none / external [ 5.955832] nouveau [ PTHERM][0000:0f:00.0] fan management: automatic [ 5.955836] nouveau [ PTHERM][0000:0f:00.0] internal sensor: yes [ 5.975835] nouveau [ CLK][0000:0f:00.0] 03: core 135 MHz shader 270 MHz memory 135 MHz [ 5.975844] nouveau [ CLK][0000:0f:00.0] 07: core 405 MHz shader 810 MHz memory 405 MHz [ 5.975851] nouveau [ CLK][0000:0f:00.0] 0f: core 520 MHz shader 1230 MHz memory 790 MHz [ 5.975880] nouveau [ CLK][0000:0f:00.0] --: core 405 MHz shader 810 MHz memory 405 MHz [ 5.976327] [TTM] Zone kernel: Available graphics memory: 12336452 kiB [ 5.976331] [TTM] Zone dma32: Available graphics memory: 2097152 kiB [ 5.976334] [TTM] Initializing pool allocator [ 5.976344] [TTM] Initializing DMA pool allocator [ 5.976364] nouveau [ DRM] VRAM: 512 MiB [ 5.976367] nouveau [ DRM] GART: 1048576 MiB [ 5.976372] nouveau [ DRM] TMDS table version 2.0 [ 5.976375] nouveau [ DRM] DCB version 4.0 [ 5.976379] nouveau [ DRM] DCB outp 00: 02000360 00000000 [ 5.976382] nouveau [ DRM] DCB outp 01: 02000362 00020010 [ 5.976385] nouveau [ DRM] DCB outp 02: 028003a6 0f220010 [ 5.976388] nouveau [ DRM] DCB outp 03: 01011380 00000000 [ 5.976391] nouveau [ DRM] DCB outp 04: 08011382 00020010 [ 5.976394] nouveau [ DRM] DCB outp 05: 088113c6 0f220010 [ 5.976398] nouveau [ DRM] DCB conn 00: 00101064 [ 5.976401] nouveau [ DRM] DCB conn 01: 00202165 [ 6.026092] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 6.026094] [drm] Driver supports precise vblank timestamp query. [ 6.043502] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/0000:0f:00.1/sound/card1/input12 [ 6.043623] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/0000:0f:00.1/sound/card1/input13 [ 6.043731] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/0000:0f:00.1/sound/card1/input15 [ 6.043798] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:03.0/0000:0f:00.1/sound/card1/input16 [ 6.078586] nouveau [ DRM] MM: using COPY for buffer copies [ 6.097627] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work properly. Using workaround [ 6.186606] nouveau [ DRM] allocated 1600x900 fb: 0x70000, bo ffff88060311cc00 [ 6.186838] fbcon: nouveaufb (fb0) is primary device [ 6.333908] Console: switching to colour frame buffer device 200x56 [ 6.336132] nouveau 0000:0f:00.0: fb0: nouveaufb frame buffer device [ 6.336135] nouveau 0000:0f:00.0: registered panic notifier [ 6.406247] [drm] Initialized nouveau 1.2.2 20120801 for 0000:0f:00.0 on minor 0 [ 7.649017] EXT4-fs (dm-0): re-mounted. Opts: (null) [ 7.791926] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro [ 8.294446] loop: module loaded [ 8.586592] raid6: sse2x1 gen() 4194 MB/s [ 8.654630] raid6: sse2x1 xor() 3259 MB/s [ 8.722647] raid6: sse2x2 gen() 4922 MB/s [ 8.790666] raid6: sse2x2 xor() 3789 MB/s [ 8.858674] raid6: sse2x4 gen() 5469 MB/s [ 8.926690] raid6: sse2x4 xor() 4164 MB/s [ 8.926692] raid6: using algorithm sse2x4 gen() 5469 MB/s [ 8.926694] raid6: .... xor() 4164 MB/s, rmw enabled [ 8.926695] raid6: using ssse3x2 recovery algorithm [ 8.944629] async_tx: api initialized (async) [ 8.948379] xor: measuring software checksum speed [ 8.986702] prefetch64-sse: 6642.000 MB/sec [ 9.026712] generic_sse: 5770.000 MB/sec [ 9.026714] xor: using function: prefetch64-sse (6642.000 MB/sec) [ 9.053530] md: raid6 personality registered for level 6 [ 9.053533] md: raid5 personality registered for level 5 [ 9.053535] md: raid4 personality registered for level 4 [ 9.065278] device-mapper: raid: Loading target version 1.6.0 [ 9.094853] md: raid1 personality registered for level 1 [ 9.096358] md/raid1:mdX: active with 2 out of 2 mirrors [ 9.096675] mdX: invalid bitmap file superblock: bad magic [ 9.096680] mdX: bitmap file superblock: [ 9.096682] magic: 00000401 [ 9.096684] version: 1041 [ 9.096687] uuid: 00000421.1ff55bd9.00040002.00000000 [ 9.096689] events: 592 [ 9.096690] events cleared: 592 [ 9.096692] state: 00000000 [ 9.096694] chunksize: 524288 B [ 9.096695] daemon sleep: 5s [ 9.096697] sync size: 262144000 KB [ 9.096699] max write behind: 0 [ 9.096703] mdX: failed to create bitmap (-22) [ 9.096808] device-mapper: table: 253:8: raid: Fail to run raid array [ 9.096824] device-mapper: ioctl: error adding target to table [ 9.192429] Adding 26214396k swap on /dev/mapper/helix-swap. Priority:-1 extents:1 across:26214396k FS [ 22.307449] EXT4-fs (sdb1): mounting ext2 file system using the ext4 subsystem [ 22.310554] EXT4-fs (sdb1): mounted filesystem without journal. Opts: (null) [ 22.336806] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null) [ 22.349134] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [ 22.776576] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 22.809495] ip_tables: (C) 2000-2006 Netfilter Core Team [ 22.929623] nf_conntrack version 0.5.0 (65536 buckets, 262144 max) [ 23.338263] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 24.579899] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 24.957043] tg3 0000:01:00.0 eth0: Link is up at 100 Mbps, full duplex [ 24.957049] tg3 0000:01:00.0 eth0: Flow control is off for TX and off for RX [ 24.957067] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 26.233928] tg3 0000:1c:00.0 eth1: Link is up at 100 Mbps, full duplex [ 26.233934] tg3 0000:1c:00.0 eth1: Flow control is off for TX and off for RX [ 26.233951] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 49.915484] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 49.940068] Bridge firewalling registered ** Model information sys_vendor: Hewlett-Packard product_name: HP Z600 Workstation product_version: chassis_vendor: Hewlett-Packard chassis_version: bios_vendor: Hewlett-Packard bios_version: 786G4 v03.54 board_vendor: Hewlett-Packard board_name: 0B54h board_version: D ** Loaded modules: ipt_MASQUERADE nf_nat_masquerade_ipv4 xt_addrtype br_netfilter bridge stp llc overlay xt_REDIRECT nf_nat_redirect iptable_nat nf_nat_ipv4 nf_nat xt_tcpudp xt_mac nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ipv6 nf_defrag_ipv6 xt_conntrack nf_conntrack iptable_filter ip_tables ip6table_filter ip6_tables x_tables raid1 dm_raid raid456 async_raid6_recov async_memcpy async_pq async_xor xor async_tx raid6_pq loop intel_powerclamp coretemp kvm_intel kvm hp_wmi sparse_keymap rfkill nouveau snd_hda_codec_hdmi crct10dif_pclmul crc32_pclmul ghash_clmulni_intel mxm_wmi video ttm drm_kms_helper drm aesni_intel ppdev iTCO_wdt iTCO_vendor_support evdev lpc_ich psmouse aes_x86_64 i2c_algo_bit serio_raw lrw gf128mul mfd_core glue_helper snd_hda_codec_realtek ablk_helper cryptd sg wmi snd_hda_codec_generic parport_pc button snd_hda_intel snd_hda_controller snd_hda_codec snd_hda_core 8250_fintek snd_hwdep snd_pcm snd_timer parport snd soundcore acpi_cpufreq processor i7core_edac thermal_sys edac_core shpchp ext4 crc16 mbcache jbd2 dm_mod md_mod hid_generic usbhid hid sr_mod cdrom sd_mod crc32c_intel ahci libahci libata firewire_ohci firewire_core crc_itu_t scsi_mod tg3 xhci_pci ehci_pci uhci_hcd ptp xhci_hcd ehci_hcd pps_core libphy usbcore usb_common floppy ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 5520 I/O Hub to ESI Port [8086:3406] (rev 13) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:01.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 [8086:3408] (rev 13) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 Memory behind bridge: fd000000-fd0fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:03.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 [8086:340a] (rev 13) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0f, subordinate=0f, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fa000000-fb0fffff Prefetchable memory behind bridge: 00000000f4000000-00000000f9ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:07.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 [8086:340e] (rev 13) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=28, subordinate=28, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:10.0 PIC [0800]: Intel Corporation 7500/5520/5500/X58 Physical and Link Layer Registers Port 0 [8086:3425] (rev 13) (prog-if 00 [8259]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:10.1 PIC [0800]: Intel Corporation 7500/5520/5500/X58 Routing and Protocol Layer Registers Port 0 [8086:3426] (rev 13) (prog-if 00 [8259]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:11.0 PIC [0800]: Intel Corporation 7500/5520/5500 Physical and Link Layer Registers Port 1 [8086:3427] (rev 13) (prog-if 00 [8259]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:11.1 PIC [0800]: Intel Corporation 7500/5520/5500 Routing & Protocol Layer Register Port 1 [8086:3428] (rev 13) (prog-if 00 [8259]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:14.0 PIC [0800]: Intel Corporation 7500/5520/5500/X58 I/O Hub System Management Registers [8086:342e] (rev 13) (prog-if 00 [8259]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> Kernel driver in use: i7core_edac 00:14.1 PIC [0800]: Intel Corporation 7500/5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers [8086:3422] (rev 13) (prog-if 00 [8259]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:14.2 PIC [0800]: Intel Corporation 7500/5520/5500/X58 I/O Hub Control Status and RAS Registers [8086:3423] (rev 13) (prog-if 00 [8259]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:15.0 PIC [0800]: Intel Corporation 7500/5520/5500/X58 Trusted Execution Technology Registers [8086:342f] (rev 13) (prog-if 20 [IO(X)-APIC]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:1a.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 [8086:3a37] (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 4: I/O ports at d000 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1a.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 [8086:3a38] (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at d020 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1a.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 [8086:3a39] (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 22 Region 4: I/O ports at d040 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1a.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 [8086:3a3c] (prog-if 20 [EHCI]) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 22 Region 0: Memory at ee004800 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci-pci 00:1b.0 Audio device [0403]: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller [8086:3a3e] Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 36 Region 0: Memory at ee000000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 [8086:3a40] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 24 Bus: primary=00, secondary=1c, subordinate=1c, sec-latency=0 I/O behind bridge: 00001000-00001fff Memory behind bridge: ef000000-ef0fffff Prefetchable memory behind bridge: 00000000ed100000-00000000ed2fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.5 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 6 [8086:3a4a] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 25 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: fc000000-fc0fffff Prefetchable memory behind bridge: 00000000ed300000-00000000ed4fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1d.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 [8086:3a34] (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 4: I/O ports at d060 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1d.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 [8086:3a35] (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at d080 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1d.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 [8086:3a36] (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 22 Region 4: I/O ports at d0a0 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1d.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 [8086:3a3a] (prog-if 20 [EHCI]) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 0: Memory at ee004c00 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci-pci 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 90) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=37, subordinate=37, sec-latency=32 Memory behind bridge: ed000000-ed0fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge [0601]: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller [8086:3a16] Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: lpc_ich 00:1f.2 RAID bus controller [0104]: Intel Corporation SATA Controller [RAID mode] [8086:2822] Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 35 Region 0: I/O ports at d100 [size=8] Region 1: I/O ports at d110 [size=4] Region 2: I/O ports at d108 [size=8] Region 3: I/O ports at d114 [size=4] Region 4: I/O ports at d0c0 [size=32] Region 5: Memory at ee004000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci 01:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5764M Gigabit Ethernet PCIe [14e4:1684] (rev 10) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 40 Region 0: Memory at fc000000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: tg3 03:00.0 USB controller [0c03]: Texas Instruments TUSB73x0 SuperSpeed USB 3.0 xHCI Host Controller [104c:8241] (rev 02) (prog-if 30 [XHCI]) Subsystem: Device [1b5b:8040] Physical Slot: 1 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 26 Region 0: Memory at fd000000 (64-bit, non-prefetchable) [size=64K] Region 2: Memory at fd010000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: xhci_hcd 0f:00.0 VGA compatible controller [0300]: NVIDIA Corporation GT218 [NVS 300] [10de:10d8] (rev a2) (prog-if 00 [VGA controller]) Subsystem: Hewlett-Packard Company Device [103c:0862] Physical Slot: 2 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 39 Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at f4000000 (64-bit, prefetchable) [size=64M] Region 3: Memory at f8000000 (64-bit, prefetchable) [size=32M] Region 5: I/O ports at e000 [size=128] [virtual] Expansion ROM at fb080000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: nouveau 0f:00.1 Audio device [0403]: NVIDIA Corporation High Definition Audio Controller [10de:0be3] (rev a1) Subsystem: Hewlett-Packard Company Device [103c:0862] Physical Slot: 2 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 37 Region 0: Memory at fb000000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 1c:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5761 Gigabit Ethernet PCIe [14e4:1681] (rev 10) Subsystem: Broadcom Corporation NetXtreme BCM5761 Gigabit Ethernet PCIe [14e4:1681] Physical Slot: 3 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 41 Region 0: Memory at ef000000 (64-bit, non-prefetchable) [size=64K] Region 2: Memory at ef010000 (64-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at ef020000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: tg3 37:05.0 FireWire (IEEE 1394) [0c00]: LSI Corporation FW322/323 [TrueFire] 1394a Controller [11c1:5811] (rev 70) (prog-if 10 [OHCI]) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (3000ns min, 6000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at ed000000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: firewire_ohci 3e:00.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series QuickPath Architecture Generic Non-core Registers [8086:2c70] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:00.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series QuickPath Architecture System Address Decoder [8086:2d81] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:02.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Link 0 [8086:2d90] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:02.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Physical 0 [8086:2d91] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:02.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Mirror Port Link 0 [8086:2d92] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:02.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Mirror Port Link 1 [8086:2d93] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:02.4 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Link 1 [8086:2d94] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:02.5 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Physical 1 [8086:2d95] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:03.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Registers [8086:2d98] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:03.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Target Address Decoder [8086:2d99] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:03.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller RAS Registers [8086:2d9a] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:03.4 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Test Registers [8086:2d9c] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:04.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Control [8086:2da0] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:04.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Address [8086:2da1] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:04.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Rank [8086:2da2] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:04.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Thermal Control [8086:2da3] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:05.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Control [8086:2da8] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:05.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Address [8086:2da9] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:05.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Rank [8086:2daa] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:05.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Thermal Control [8086:2dab] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:06.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Control [8086:2db0] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:06.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Address [8086:2db1] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:06.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Rank [8086:2db2] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3e:06.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Thermal Control [8086:2db3] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:00.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series QuickPath Architecture Generic Non-core Registers [8086:2c70] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:00.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series QuickPath Architecture System Address Decoder [8086:2d81] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:02.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Link 0 [8086:2d90] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:02.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Physical 0 [8086:2d91] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:02.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Mirror Port Link 0 [8086:2d92] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:02.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Mirror Port Link 1 [8086:2d93] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:02.4 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Link 1 [8086:2d94] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:02.5 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Physical 1 [8086:2d95] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:03.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Registers [8086:2d98] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:03.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Target Address Decoder [8086:2d99] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:03.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller RAS Registers [8086:2d9a] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:03.4 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Test Registers [8086:2d9c] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:04.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Control [8086:2da0] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:04.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Address [8086:2da1] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:04.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Rank [8086:2da2] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:04.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Thermal Control [8086:2da3] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:05.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Control [8086:2da8] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:05.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Address [8086:2da9] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:05.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Rank [8086:2daa] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:05.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Thermal Control [8086:2dab] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:06.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Control [8086:2db0] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:06.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Address [8086:2db1] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:06.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Rank [8086:2db2] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:06.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Thermal Control [8086:2db3] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:130a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ** USB devices: Bus 010 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 008 Device 002: ID 046d:c078 Logitech, Inc. Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -- System Information: Debian Release: stretch/sid APT prefers testing APT policy: (990, 'testing'), (500, 'testing-updates'), (500, 'stable-updates'), (500, 'unstable'), (500, 'stable') Architecture: amd64 (x86_64) Kernel: Linux 4.1.0-2-amd64 (SMP w/8 CPU cores) Locale: LANG=ja_JP.UTF-8, LC_CTYPE=ja_JP.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Init: sysvinit (via /sbin/init) Versions of packages linux-image-4.1.0-2-amd64 depends on: ii debconf [debconf-2.0] 1.5.57 ii initramfs-tools [linux-initramfs-tool] 0.120 ii kmod 21-1 ii linux-base 4.0 Versions of packages linux-image-4.1.0-2-amd64 recommends: pn firmware-linux-free <none> pn irqbalance <none> Versions of packages linux-image-4.1.0-2-amd64 suggests: pn debian-kernel-handbook <none> ii grub-pc 2.02~beta2-28 pn linux-doc-4.1 <none> Versions of packages linux-image-4.1.0-2-amd64 is related to: pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> pn firmware-linux <none> pn firmware-linux-nonfree <none> pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-ralink <none> pn firmware-realtek <none> pn xen-hypervisor <none> -- debconf information: linux-image-4.1.0-2-amd64/postinst/depmod-error-initrd-4.1.0-2-amd64: false linux-image-4.1.0-2-amd64/postinst/mips-initrd-4.1.0-2-amd64: linux-image-4.1.0-2-amd64/prerm/removing-running-kernel-4.1.0-2-amd64: true Hope this helps, -- Olaf Meeuwissen, LPIC-2 EPSON FLOSS Engineer -- AVASYS CORPORATION FSF Associate Member #1962 Help support software freedom http://www.fsf.org/jf?referrer=1962[2]
--- End Message ---
--- Begin Message ---Hi This bug was filed for a very old kernel or the bug is old itself without resolution. If you can reproduce it with - the current version in unstable/testing - the latest kernel from backports please reopen the bug, see https://www.debian.org/Bugs/server-control for details. Regards, Salvatore
--- End Message ---
