Package: src:linux Version: 6.1.76-1 Severity: normal X-Debbugs-Cc: da...@balch.co.uk
Dear Maintainer, *** Reporter, please consider answering these questions, where appropriate *** * What led up to the situation? I am trying to get WoWLAN working on an old DELL via a PCIe WiFi card ( https://www.amazon.co.uk/dp/B0BTCNG9TD?psc=1&ref=ppx_yo2ov_dt_b_product_details ) that uses the Intel 7265 chipset ( https://www.intel.com/content/www/us/en/products/sku/83635/intel-dual-band-wirelessac-7265/specifications.html ). The card's result from lspci: 03:00.0 Network controller [0280]: "Intel Corporation Wireless 7265 [8086:095a] (rev 59)" * What exactly did you do (or not do) that was effective (or ineffective)? 1. Enabled WoWLAN with magic-packet with `iw phy0 wowlan enable magic-packet` 2. Suspend PC with `echo "mem" > /sys/power/state` 3. After suspend, press a key. I also tried this with a pristine build of linux 6.7.6, and encountered the same problem. * What was the outcome of this action? The display lit up, showing the same information as before suspend, but the mouse and keyboard don't respond. Magic SysRq does respond. I found my way to seeing the kernel crash message (via preventing console_suspend, and tweaking /proc/sys/kernel/{prink,sysrq} values), as shown in the image at: https://imgur.com/a/E7dD0ND Initial analysis of that photo from iam_tj[m]1 on irc #debian-kernel (2024-02-29 19:48): >From your photo we see >`drivers/net/wireless/intel/iwlwifi/iwl-trans.c::iwl_trans_txq_enable_cfg()` >report "bad state" and that is called from >`drivers/net/wireless/intel/iwlwifi/mvm/d3.c::iwl_mvm_send_wowlan_get_status()` > that reports "failed to query wakeup status (-5)". >From reading the code around WoWLAN it seems a special WoWLAN firmware should >be loaded into the device on suspend and on resume the driver is checking it >is (still) there. If not the driver should cause a full device reset. `asm_exc_invalid_op` is a TRAP leading to `arch/x86/kernel/traps.c::handle_invalid_op()` which may imply the code in RAM has been corrupted (in the function `iwl_pcie_tx_start()` presumably). Doesn't seem too likely though since code (.text sections) should be read-only unless the RAM itself is faulty - but if that one wouldn't expect the same error every time. * What outcome did you expect instead? The system resumes from suspend and is fully interactive (as it does when WoWLAN is disabled). -- Package-specific info: ** Version: Linux version 6.1.0-18-amd64 (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT_DYNAMIC Debian 6.1.76-1 (2024-02-01) ** Command line: BOOT_IMAGE=/boot/vmlinuz-6.1.0-18-amd64 root=UUID=b15802a9-4b38-4cb9-9109-fdf1cad881b0 ro quiet crashkernel=384M-:128M ** Not tainted ** Kernel log: [ 4.039828] mei_me 0000:00:16.0: enabling device (0000 -> 0002) [ 4.064801] input: PC Speaker as /devices/platform/pcspkr/input/input9 [ 4.066671] ee1004 0-0051: 512 byte EE1004-compliant SPD EEPROM, read-only [ 4.066685] ee1004 0-0053: 512 byte EE1004-compliant SPD EEPROM, read-only [ 4.110654] iTCO_wdt iTCO_wdt: Found a Intel PCH TCO device (Version=4, TCOBASE=0x0400) [ 4.112303] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.4) [ 4.113931] iTCO_wdt iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 4.128354] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 4.128506] cfg80211: Loaded X.509 cert 'b...@debian.org: 577e021cb980e0e820821ba7b54b4961b8b4fadf' [ 4.128645] cfg80211: Loaded X.509 cert 'romain.per...@gmail.com: 3abbc6ec146e09d1b6016ab9d6cf71dd233f0328' [ 4.128783] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 4.128917] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 4.133009] platform regulatory.0: firmware: direct-loading firmware regulatory.db [ 4.133129] platform regulatory.0: firmware: direct-loading firmware regulatory.db.p7s [ 4.133616] input: Dell WMI hotkeys as /devices/platform/PNP0C14:00/wmi_bus/wmi_bus-PNP0C14:00/9DBB5994-A997-11DA-B012-B622A1EF5492/input/input10 [ 4.154628] Intel(R) Wireless WiFi driver for Linux [ 4.166726] pcieport 0000:00:1d.0: Intel SPT PCH root port ACS workaround enabled [ 4.166880] iwlwifi 0000:03:00.0: enabling device (0100 -> 0102) [ 4.169833] iwlwifi 0000:03:00.0: firmware: direct-loading firmware iwlwifi-7265D-29.ucode [ 4.169856] iwlwifi 0000:03:00.0: Found debug destination: EXTERNAL_DRAM [ 4.169857] iwlwifi 0000:03:00.0: Found debug configuration: 0 [ 4.170045] iwlwifi 0000:03:00.0: loaded firmware version 29.4063824552.0 7265D-29.ucode op_mode iwlmvm [ 4.184779] snd_hda_intel 0000:00:1f.3: enabling device (0100 -> 0102) [ 4.187148] RAPL PMU: API unit is 2^-32 Joules, 4 fixed counters, 655360 ms ovfl timer [ 4.187150] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules [ 4.187151] RAPL PMU: hw unit of domain package 2^-14 Joules [ 4.187151] RAPL PMU: hw unit of domain dram 2^-14 Joules [ 4.187152] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules [ 4.189485] cryptd: max_cpu_qlen set to 1000 [ 4.198676] AVX2 version of gcm_enc/dec engaged. [ 4.198702] AES CTR mode by8 optimization enabled [ 4.204401] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915]) [ 4.264476] iwlwifi 0000:03:00.0: Detected Intel(R) Dual Band Wireless AC 7265, REV=0x210 [ 4.264703] thermal thermal_zone3: failed to read out thermal zone (-61) [ 4.287825] iwlwifi 0000:03:00.0: Applying debug destination EXTERNAL_DRAM [ 4.288137] iwlwifi 0000:03:00.0: Allocated 0x00400000 bytes for firmware monitor. [ 4.292573] iwlwifi 0000:03:00.0: base HW address: 98:43:fa:68:6c:30, OTP minor version: 0x0 [ 4.292779] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC3234: line_outs=1 (0x1b/0x0/0x0/0x0/0x0) type:line [ 4.292783] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=1 (0x14/0x0/0x0/0x0/0x0) [ 4.292785] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0) [ 4.292787] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0 [ 4.292788] snd_hda_codec_realtek hdaudioC0D0: inputs: [ 4.292789] snd_hda_codec_realtek hdaudioC0D0: Headset Mic=0x19 [ 4.292790] snd_hda_codec_realtek hdaudioC0D0: Headphone Mic=0x1a [ 4.354380] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' [ 4.358756] intel_rapl_common: Found RAPL domain package [ 4.358758] intel_rapl_common: Found RAPL domain core [ 4.358760] intel_rapl_common: Found RAPL domain uncore [ 4.358761] intel_rapl_common: Found RAPL domain dram [ 4.384671] iwlwifi 0000:03:00.0 wlp3s0: renamed from wlan0 [ 4.673925] BTRFS info (device sda): first mount of filesystem 627a8e1c-6e69-4af6-a231-01976a80f6ae [ 4.673949] BTRFS info (device sda): using crc32c (crc32c-intel) checksum algorithm [ 4.673960] BTRFS info (device sda): using free space tree [ 4.794108] audit: type=1400 audit(1709239155.743:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=610 comm="apparmor_parser" [ 4.795702] audit: type=1400 audit(1709239155.743:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=611 comm="apparmor_parser" [ 4.795713] audit: type=1400 audit(1709239155.743:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=611 comm="apparmor_parser" [ 4.812151] audit: type=1400 audit(1709239155.759:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/freshclam" pid=614 comm="apparmor_parser" [ 4.817780] audit: type=1400 audit(1709239155.767:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=612 comm="apparmor_parser" [ 4.817793] audit: type=1400 audit(1709239155.767:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=612 comm="apparmor_parser" [ 4.817800] audit: type=1400 audit(1709239155.767:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=612 comm="apparmor_parser" [ 4.817806] audit: type=1400 audit(1709239155.767:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/{,usr/}sbin/dhclient" pid=612 comm="apparmor_parser" [ 4.820090] audit: type=1400 audit(1709239155.767:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=615 comm="apparmor_parser" [ 4.899000] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1f.3/sound/card0/input11 [ 4.899669] input: HDA Intel PCH Headphone Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input12 [ 4.899888] input: HDA Intel PCH Line Out as /devices/pci0000:00/0000:00:1f.3/sound/card0/input13 [ 4.900941] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input14 [ 4.901815] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input15 [ 4.902755] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input16 [ 12.972154] kauditd_printk_skb: 16 callbacks suppressed [ 12.972160] audit: type=1400 audit(1709239163.919:27): apparmor="DENIED" operation="capable" profile="/usr/sbin/cupsd" pid=3701 comm="cupsd" capability=12 capname="net_admin" [ 13.035891] NET: Registered PF_QIPCRTR protocol family [ 13.392485] iwlwifi 0000:03:00.0: Applying debug destination EXTERNAL_DRAM [ 13.470314] iwlwifi 0000:03:00.0: Applying debug destination EXTERNAL_DRAM [ 13.471436] iwlwifi 0000:03:00.0: FW already configured (0) - re-configuring [ 13.548359] iwlwifi 0000:03:00.0: Applying debug destination EXTERNAL_DRAM [ 13.626023] iwlwifi 0000:03:00.0: Applying debug destination EXTERNAL_DRAM [ 13.627196] iwlwifi 0000:03:00.0: FW already configured (0) - re-configuring [ 16.802828] e1000e 0000:00:1f.6 enp0s31f6: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 16.802899] IPv6: ADDRCONF(NETDEV_CHANGE): enp0s31f6: link becomes ready [ 17.394243] wlp3s0: authenticate with 4c:22:f3:aa:0a:c3 [ 17.394269] wlp3s0: 80 MHz not supported, disabling VHT [ 17.439194] wlp3s0: send auth to 4c:22:f3:aa:0a:c3 (try 1/3) [ 17.441336] wlp3s0: authenticated [ 17.444294] wlp3s0: associate with 4c:22:f3:aa:0a:c3 (try 1/3) [ 17.448386] wlp3s0: RX AssocResp from 4c:22:f3:aa:0a:c3 (capab=0x1411 status=0 aid=3) [ 17.454994] wlp3s0: associated [ 17.624456] wlp3s0: Limiting TX power to 20 (20 - 0) dBm as advertised by 4c:22:f3:aa:0a:c3 [ 17.640604] IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s0: link becomes ready [ 17.691007] rfkill: input handler disabled [ 27.115364] rfkill: input handler enabled [ 31.071014] rfkill: input handler disabled [ 34.056885] wlp3s0: disconnect from AP 4c:22:f3:aa:0a:c3 for new auth to 4c:22:f3:aa:0a:c2 [ 34.125550] wlp3s0: authenticate with 4c:22:f3:aa:0a:c2 [ 34.131140] wlp3s0: send auth to 4c:22:f3:aa:0a:c2 (try 1/3) [ 34.134678] wlp3s0: authenticated [ 34.140292] wlp3s0: associate with 4c:22:f3:aa:0a:c2 (try 1/3) [ 34.141995] wlp3s0: RX ReassocResp from 4c:22:f3:aa:0a:c2 (capab=0x1011 status=0 aid=1) [ 34.143766] wlp3s0: associated [ 34.147629] wlp3s0: Limiting TX power to 19 (20 - 1) dBm as advertised by 4c:22:f3:aa:0a:c2 [ 40.188417] e1000e 0000:00:1f.6 enp0s31f6: NIC Link is Down ** Model information sys_vendor: Dell Inc. product_name: OptiPlex 7040 product_version: chassis_vendor: Dell Inc. chassis_version: bios_vendor: Dell Inc. bios_version: 1.24.0 board_vendor: Dell Inc. board_name: 0HD5W2 board_version: A00 ** Loaded modules: ctr ccm snd_seq_dummy snd_hrtimer snd_seq snd_seq_device qrtr cpuid snd_hda_codec_hdmi binfmt_misc nls_ascii nls_cp437 vfat fat intel_rapl_msr intel_rapl_common x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel snd_ctl_led kvm irqbypass ghash_clmulni_intel iwlmvm sha512_ssse3 sha512_generic snd_hda_codec_realtek sha256_ssse3 sha1_ssse3 snd_hda_codec_generic mac80211 aesni_intel crypto_simd cryptd rapl libarc4 snd_hda_intel snd_intel_dspcfg snd_intel_sdw_acpi intel_cstate iwlwifi ledtrig_audio intel_uncore dell_wmi snd_hda_codec mei_hdcp mei_wdt sparse_keymap snd_hda_core snd_hwdep dell_smbios snd_pcm dcdbas iTCO_wdt cfg80211 dell_wmi_descriptor wmi_bmof ee1004 pcspkr snd_timer intel_pmc_bxt iTCO_vendor_support mei_me snd rfkill watchdog soundcore mei intel_pch_thermal intel_pmc_core acpi_pad evdev sg msr parport_pc ppdev fuse lp parport dm_mod efi_pstore loop configfs efivarfs ip_tables x_tables autofs4 ext4 crc16 mbcache jbd2 btrfs blake2b_generic xor raid6_pq zstd_compress libcrc32c crc32c_generic i915 hid_generic usbhid sr_mod hid cdrom sd_mod drm_buddy i2c_algo_bit drm_display_helper nvme cec nvme_core rc_core t10_pi ttm ahci drm_kms_helper libahci crc64_rocksoft crc64 crc_t10dif xhci_pci crc32_pclmul xhci_hcd crc32c_intel crct10dif_generic libata drm i2c_i801 e1000e i2c_smbus usbcore scsi_mod crct10dif_pclmul crct10dif_common scsi_common usb_common fan video wmi button ** Network interface configuration: *** /etc/network/interfaces: source /etc/network/interfaces.d/* auto lo iface lo inet loopback ** Network status: *** IP interfaces and addresses: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host noprefixroute valid_lft forever preferred_lft forever 2: enp0s31f6: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN group default qlen 1000 link/ether 64:00:6a:8e:9a:7f brd ff:ff:ff:ff:ff:ff 3: wlp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000 link/ether 98:43:fa:68:6c:30 brd ff:ff:ff:ff:ff:ff inet 192.168.1.204/24 brd 192.168.1.255 scope global dynamic noprefixroute wlp3s0 valid_lft 85378sec preferred_lft 85378sec inet6 fe80::da96:b5fd:9e3:c29a/64 scope link noprefixroute valid_lft forever preferred_lft forever *** Device statistics: Inter-| Receive | Transmit face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed lo: 4890 43 0 0 0 0 0 0 4890 43 0 0 0 0 0 0 enp0s31f6: 1664 7 0 0 0 0 0 4 3460 21 0 0 0 0 0 0 wlp3s0: 7943550 9775 0 0 0 0 0 0 2006794 5646 0 0 0 0 0 0 ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Host Bridge/DRAM Registers [8086:191f] (rev 07) Subsystem: Dell Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Host Bridge/DRAM Registers [1028:06b9] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 IOMMU group: 1 Capabilities: <access denied> Kernel driver in use: skl_uncore Kernel modules: ie31200_edac 00:01.0 PCI bridge [0604]: Intel Corporation 6th-10th Gen Core Processor PCIe Controller (x16) [8086:1901] (rev 07) (prog-if 00 [Normal decode]) Subsystem: Dell 6th-10th Gen Core Processor PCIe Controller (x16) [1028:06b9] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 122 IOMMU group: 2 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: [disabled] [16-bit] Memory behind bridge: [disabled] [32-bit] Prefetchable memory behind bridge: [disabled] [64-bit] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:02.0 VGA compatible controller [0300]: Intel Corporation HD Graphics 530 [8086:1912] (rev 06) (prog-if 00 [VGA controller]) Subsystem: Dell HD Graphics 530 [1028:06b9] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 133 IOMMU group: 0 Region 0: Memory at f6000000 (64-bit, non-prefetchable) [size=16M] Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at f000 [size=64] Expansion ROM at 000c0000 [virtual] [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:14.0 USB controller [0c03]: Intel Corporation 100 Series/C230 Series Chipset Family USB 3.0 xHCI Controller [8086:a12f] (rev 31) (prog-if 30 [XHCI]) Subsystem: Dell 100 Series/C230 Series Chipset Family USB 3.0 xHCI Controller [1028:06b9] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 126 IOMMU group: 3 Region 0: Memory at f7230000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: xhci_hcd Kernel modules: xhci_pci 00:14.2 Signal processing controller [1180]: Intel Corporation 100 Series/C230 Series Chipset Family Thermal Subsystem [8086:a131] (rev 31) Subsystem: Dell 100 Series/C230 Series Chipset Family Thermal Subsystem [1028:06b9] Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 18 IOMMU group: 3 Region 0: Memory at f724f000 (64-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: intel_pch_thermal Kernel modules: intel_pch_thermal 00:16.0 Communication controller [0780]: Intel Corporation 100 Series/C230 Series Chipset Family MEI Controller #1 [8086:a13a] (rev 31) Subsystem: Dell 100 Series/C230 Series Chipset Family MEI Controller [1028:06b9] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 134 IOMMU group: 4 Region 0: Memory at f724e000 (64-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: mei_me Kernel modules: mei_me 00:16.3 Serial controller [0700]: Intel Corporation 100 Series/C230 Series Chipset Family KT Redirection [8086:a13d] (rev 31) (prog-if 02 [16550]) Subsystem: Dell 100 Series/C230 Series Chipset Family KT Redirection [1028:06b9] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin D routed to IRQ 19 IOMMU group: 4 Region 0: I/O ports at f0a0 [size=8] Region 1: Memory at f724d000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: serial 00:17.0 SATA controller [0106]: Intel Corporation Q170/Q150/B150/H170/H110/Z170/CM236 Chipset SATA Controller [AHCI Mode] [8086:a102] (rev 31) (prog-if 01 [AHCI 1.0]) Subsystem: Dell Q170/Q150/B150/H170/H110/Z170/CM236 Chipset SATA Controller [AHCI Mode] [1028:06b9] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 127 IOMMU group: 5 Region 0: Memory at f7248000 (32-bit, non-prefetchable) [size=8K] Region 1: Memory at f724c000 (32-bit, non-prefetchable) [size=256] Region 2: I/O ports at f090 [size=8] Region 3: I/O ports at f080 [size=4] Region 4: I/O ports at f060 [size=32] Region 5: Memory at f724b000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci Kernel modules: ahci 00:1b.0 PCI bridge [0604]: Intel Corporation 100 Series/C230 Series Chipset Family PCI Express Root Port #17 [8086:a167] (rev f1) (prog-if 00 [Normal decode]) Subsystem: Dell 100 Series/C230 Series Chipset Family PCI Express Root Port [1028:06b9] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 123 IOMMU group: 6 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: e000-efff [size=4K] [16-bit] Memory behind bridge: f7100000-f71fffff [size=1M] [32-bit] Prefetchable memory behind bridge: [disabled] [64-bit] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1d.0 PCI bridge [0604]: Intel Corporation 100 Series/C230 Series Chipset Family PCI Express Root Port #9 [8086:a118] (rev f1) (prog-if 00 [Normal decode]) Subsystem: Dell 100 Series/C230 Series Chipset Family PCI Express Root Port [1028:06b9] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 124 IOMMU group: 7 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: [disabled] [16-bit] Memory behind bridge: f7000000-f70fffff [size=1M] [32-bit] Prefetchable memory behind bridge: [disabled] [64-bit] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1f.0 ISA bridge [0601]: Intel Corporation Q170 Chipset LPC/eSPI Controller [8086:a146] (rev 31) Subsystem: Dell Q170 Chipset LPC/eSPI Controller [1028:06b9] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 IOMMU group: 8 00:1f.2 Memory controller [0580]: Intel Corporation 100 Series/C230 Series Chipset Family Power Management Controller [8086:a121] (rev 31) Subsystem: Dell 100 Series/C230 Series Chipset Family Power Management Controller [1028:06b9] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- IOMMU group: 8 Region 0: Memory at f7244000 (32-bit, non-prefetchable) [disabled] [size=16K] 00:1f.3 Audio device [0403]: Intel Corporation 100 Series/C230 Series Chipset Family HD Audio Controller [8086:a170] (rev 31) Subsystem: Dell 100 Series/C230 Series Chipset Family HD Audio Controller [1028:06b9] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 136 IOMMU group: 8 Region 0: Memory at f7240000 (64-bit, non-prefetchable) [size=16K] Region 4: Memory at f7220000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd_hda_intel 00:1f.4 SMBus [0c05]: Intel Corporation 100 Series/C230 Series Chipset Family SMBus [8086:a123] (rev 31) Subsystem: Dell 100 Series/C230 Series Chipset Family SMBus [1028:06b9] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 16 IOMMU group: 8 Region 0: Memory at f724a000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at f040 [size=32] Kernel driver in use: i801_smbus Kernel modules: i2c_i801 00:1f.6 Ethernet controller [0200]: Intel Corporation Ethernet Connection (2) I219-LM [8086:15b7] (rev 31) Subsystem: Dell Ethernet Connection (2) I219-LM [1028:06b9] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 125 IOMMU group: 9 Region 0: Memory at f7200000 (32-bit, non-prefetchable) [size=128K] Capabilities: <access denied> Kernel driver in use: e1000e Kernel modules: e1000e 02:00.0 Non-Volatile memory controller [0108]: Samsung Electronics Co Ltd NVMe SSD Controller SM951/PM951 [144d:a802] (rev 01) (prog-if 02 [NVM Express]) Subsystem: Samsung Electronics Co Ltd PM963 2.5" NVMe PCIe SSD [144d:a801] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 IOMMU group: 10 Region 0: Memory at f7100000 (64-bit, non-prefetchable) [size=16K] Region 2: I/O ports at e000 [size=256] Capabilities: <access denied> Kernel driver in use: nvme Kernel modules: nvme 03:00.0 Network controller [0280]: Intel Corporation Wireless 7265 [8086:095a] (rev 59) Subsystem: Intel Corporation Dual Band Wireless-AC 7265 [Stone Peak 2 AC] [8086:9010] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 135 IOMMU group: 11 Region 0: Memory at f7000000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: iwlwifi Kernel modules: iwlwifi ** USB devices: Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 045e:0040 Microsoft Corp. Wheel Mouse Optical Bus 001 Device 002: ID 04f2:0402 Chicony Electronics Co., Ltd Genius LuxeMate i200 Keyboard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -- System Information: Debian Release: 12.5 APT prefers stable-updates APT policy: (500, 'stable-updates'), (500, 'stable') Architecture: amd64 (x86_64) Foreign Architectures: i386 Kernel: Linux 6.1.0-18-amd64 (SMP w/4 CPU threads; PREEMPT) Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8), LANGUAGE=en_GB:en Shell: /bin/sh linked to /usr/bin/dash Init: systemd (via /run/systemd/system) LSM: AppArmor: enabled Versions of packages linux-image-6.1.0-18-amd64 depends on: ii initramfs-tools [linux-initramfs-tool] 0.142 ii kmod 30+20221128-1 ii linux-base 4.9 Versions of packages linux-image-6.1.0-18-amd64 recommends: ii apparmor 3.0.8-3 ii firmware-linux-free 20200122-1 Versions of packages linux-image-6.1.0-18-amd64 suggests: pn debian-kernel-handbook <none> ii grub-efi-amd64 2.06-13+deb12u1 pn linux-doc-6.1 <none> Versions of packages linux-image-6.1.0-18-amd64 is related to: pn firmware-amd-graphics <none> pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-cavium <none> pn firmware-intel-sound <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> ii firmware-iwlwifi 20230210-5 pn firmware-libertas <none> pn firmware-linux-nonfree <none> ii firmware-misc-nonfree 20230210-5 pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> ii firmware-realtek 20230210-5 pn firmware-samsung <none> pn firmware-siano <none> pn firmware-ti-connectivity <none> pn xen-hypervisor <none> -- no debconf information
