Package: src:linux Version: 6.12.107-1 Severity: important X-Debbugs-Cc: [email protected]
Dear Maintainer, I am reporting a reproducible amdgpu/VCE regression on Debian 13 (trixie) with an AMD Radeon RX 480 / Polaris10 GPU. Active RustDesk remote-control sessions are stable on Debian kernel 6.12.101-1 but trigger a VCE ring timeout and GPU reset on 6.12.105-1 and 6.12.107-1. Expected behavior ================= Active RustDesk screen-capture and remote-control sessions should not wedge the VCE engine, reset the GPU, or terminate the graphical desktop. Actual behavior =============== On 6.12.105 and 6.12.107, an active RustDesk session reproducibly reaches: RustDesk active session -> amdgpu ring vce0 timeout naming rustdesk -> GPU reset The severe 6.12.105 runs additionally reached: -> VCE suspension failure -> VRAM loss -> X11/GNOME session teardown -> GDM The controlled 6.12.107 run was stopped at the predetermined failure boundary after the RustDesk connection froze, the vce0 timeout named RustDesk, and GPU reset began. That particular run did not record VRAM loss or full X11 teardown. System and userspace ==================== * Debian GNU/Linux 13.6 (trixie), amd64 * AMD Radeon RX 480 / Polaris10, PCI ID 1002:67df, amdgpu * GNOME/GDM X11 * RustDesk 1.4.9 * Official native RustDesk Debian package and package-provided system service are the primary reproducer * firmware-amd-graphics 20250410-2 * Mesa 25.0.7-2+deb13u1 * No NVIDIA hardware, installed NVIDIA userspace, or loaded NVIDIA module participates in the final reproducer The native RustDesk package came from the official rustdesk/rustdesk 1.4.9 release. The Debian asset was rustdesk-1.4.9-x86_64.deb, SHA-256: 7244ba47c40e804172044bfbe659467c54ce46554c98e78c8c0406f1d612fda3. Regression matrix ================= * linux-image-6.12.101+deb13-amd64 6.12.101-1: PASS / stable * linux-image-6.12.105+deb13-amd64 6.12.105-1: FAIL * linux-image-6.12.107+deb13-amd64 6.12.107-1: FAIL 6.12.105 repeatedly failed during RustDesk sessions. Flatpak RustDesk 1.4.9 independently reproduced the failure, and the official native RustDesk 1.4.9 package/system service reproduced it in a controlled test after approximately 30 seconds. The official native RustDesk 1.4.9 service reproduced on 6.12.107 after approximately 15 seconds of active remote use. On the same hardware and substantially the same userspace and RustDesk configuration, native RustDesk repeatedly passes on 6.12.101. Successful tests include interactive use, control at GDM, GDM-to-GNOME transitions, logout/login, sustained sessions, disconnect/reconnect cycles, and a final 7,201-second unattended monitor (1,355 samples) with zero VCE timeout, GPU reset, VRAM-loss, or graphical-session teardown events. This packaging-independent result shows that the observed regression is not specific to the Flatpak sandbox or packaging. I am not claiming that RustDesk itself is conclusively innocent or that a particular upstream commit is responsible. The evidence establishes a kernel/AMDGPU/VCE regression, or a kernel-specific interaction, triggered by this workload; source-level cause has not yet been isolated. Representative 6.12.105 native-service failure ================================================ amdgpu: ring vce0 timeout, signaled seq=63, emitted seq=64 amdgpu: Process information: process rustdesk pid 4790 thread rustdesk:cs0 pid 7411 amdgpu: GPU reset begin! amdgpu: failed to suspend display audio suspend of IP block <vce_v3_0> failed -22 amdgpu: GPU reset succeeded, trying to resume [drm] VRAM is lost due to GPU reset! amdgpu: GPU reset(1) succeeded! gnome-shell: X connection to :0 broken (explicit kill or server shutdown). Representative 6.12.107 native-service failure ================================================ amdgpu: ring vce0 timeout, signaled seq=127, emitted seq=128 amdgpu: Process information: process rustdesk pid 4670 thread rustdesk:cs0 pid 21229 amdgpu: GPU reset begin! amdgpu: failed to suspend display audio amdgpu: GPU reset(1) succeeded! Reproducer ========== 1. Boot the affected Debian kernel with the RX 480 bound to amdgpu. 2. Start the normal GNOME/GDM X11 graphical session. 3. Use RustDesk 1.4.9 through its native package/system service to establish an active remote-control session. 4. Interact normally with the desktop while monitoring the kernel journal. 5. Within roughly 15-30 seconds in the controlled failing runs, the remote session freezes and the vce0 timeout/reset sequence appears. I did not intentionally reproduce the reset again while collecting this reportbug metadata under 6.12.107. Workaround ========== Persistent GRUB selection currently boots 6.12.101, which restores stable RustDesk operation. No kernel packages are held, so future candidate kernels can continue to be installed and explicitly tested. SSH survives the GPU-reset event, so this should not be characterized as a full-system crash. It is nevertheless a repeatable regression capable of resetting the GPU and, on 6.12.105, terminating the graphical session. The reportbug-generated kernel and package information follows. -- Package-specific info: ** Version: Linux version 6.12.107+deb13-amd64 ([email protected]) (x86_64-linux-gnu-gcc-14 (Debian 14.2.0-19) 14.2.0, GNU ld (GNU Binutils for Debian) 2.44) #1 SMP PREEMPT_DYNAMIC Debian 6.12.107-1 (2026-08-29) ** Command line: BOOT_IMAGE=/boot/vmlinuz-6.12.107+deb13-amd64 root=<redacted> ro quiet ** Not tainted ** Kernel log: [ 12.174248] systemd[1]: [email protected]: Deactivated successfully. [ 12.174563] systemd[1]: Finished [email protected] - Load Kernel Module fuse. [ 12.178247] systemd[1]: Mounting sys-fs-fuse-connections.mount - FUSE Control File System... [ 12.180149] systemd[1]: Starting systemd-tmpfiles-setup-dev-early.service - Create Static Device Nodes in /dev gracefully... [ 12.197374] systemd[1]: [email protected]: Deactivated successfully. [ 12.197811] systemd[1]: Finished [email protected] - Load Kernel Module configfs. [ 12.198193] systemd[1]: Mounted sys-fs-fuse-connections.mount - FUSE Control File System. [ 12.200335] systemd[1]: Mounting sys-kernel-config.mount - Kernel Configuration File System... [ 12.202778] systemd[1]: modprobe@efi_pstore.service: Deactivated successfully. [ 12.203147] systemd[1]: Finished modprobe@efi_pstore.service - Load Kernel Module efi_pstore. [ 12.216553] systemd[1]: Mounted sys-kernel-config.mount - Kernel Configuration File System. [ 12.219991] systemd[1]: Finished systemd-udev-load-credentials.service - Load udev Rules from Credentials. [ 12.221138] systemd-journald[405]: Collecting audit messages is disabled. [ 12.224076] EXT4-fs (sda1): re-mounted 55d2d272-0af9-4c14-bf30-882f481b086e r/w. [ 12.226449] systemd[1]: Finished systemd-remount-fs.service - Remount Root and Kernel File Systems. [ 12.227263] systemd[1]: systemd-hwdb-update.service - Rebuild Hardware Database skipped, unmet condition check ConditionNeedsUpdate=/etc [ 12.227341] systemd[1]: systemd-pstore.service - Platform Persistent Storage Archival skipped, unmet condition check ConditionDirectoryNotEmpty=/sys/fs/pstore [ 12.235417] systemd[1]: Starting systemd-random-seed.service - Load/Save OS Random Seed... [ 12.235469] systemd[1]: systemd-tpm2-setup.service - TPM SRK Setup skipped, unmet condition check ConditionSecurity=measured-uki [ 12.244139] lp: driver loaded but no devices found [ 12.258653] ppdev: user-space parallel port driver [ 12.270586] systemd[1]: Finished systemd-tmpfiles-setup-dev-early.service - Create Static Device Nodes in /dev gracefully. [ 12.270927] systemd[1]: systemd-sysusers.service - Create System Users skipped, no trigger condition checks were met. [ 12.272119] parport_pc 00:03: reported by Plug and Play ACPI [ 12.272213] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP] [ 12.280475] systemd[1]: Starting systemd-timesyncd.service - Network Time Synchronization... [ 12.292336] systemd[1]: Starting systemd-tmpfiles-setup-dev.service - Create Static Device Nodes in /dev... [ 12.296584] Key type psk registered [ 12.316941] systemd[1]: Finished keyboard-setup.service - Set the console keyboard layout. [ 12.317633] systemd[1]: modprobe@nvme_fabrics.service: Deactivated successfully. [ 12.317958] systemd[1]: Finished modprobe@nvme_fabrics.service - Load Kernel Module nvme_fabrics. [ 12.340705] systemd[1]: Finished systemd-tmpfiles-setup-dev.service - Create Static Device Nodes in /dev. [ 12.342834] systemd[1]: Starting systemd-udevd.service - Rule-based Manager for Device Events and Files... [ 12.377593] lp0: using parport0 (interrupt-driven). [ 12.385138] systemd[1]: Started systemd-timesyncd.service - Network Time Synchronization. [ 12.385276] systemd[1]: Reached target time-set.target - System Time Set. [ 12.404134] i2c_dev: i2c /dev entries driver [ 12.440615] systemd[1]: Started systemd-journald.service - Journal Service. [ 12.495903] systemd-journald[405]: Received client request to flush runtime journal. [ 12.837292] sr 3:0:0:0: Attached scsi generic sg0 type 5 [ 12.837549] sd 8:0:0:0: Attached scsi generic sg1 type 0 [ 12.837807] sd 9:0:0:0: Attached scsi generic sg2 type 0 [ 12.838054] sd 10:0:0:0: Attached scsi generic sg3 type 0 [ 12.838344] sd 10:0:0:1: Attached scsi generic sg4 type 0 [ 12.840975] sd 10:0:0:2: Attached scsi generic sg5 type 0 [ 12.842936] sd 10:0:0:3: Attached scsi generic sg6 type 0 [ 12.952035] random: crng init done [ 13.160152] input: PC Speaker as /devices/platform/pcspkr/input/input4 [ 13.208540] Adding 6288380k swap on /dev/sda5. Priority:-2 extents:1 across:6288380k SS [ 13.307051] snd_hda_intel 0000:01:00.1: Force to non-snoop mode [ 13.343817] snd_hda_intel 0000:01:00.1: bound 0000:01:00.0 (ops amdgpu_dm_audio_component_bind_ops [amdgpu]) [ 13.361416] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input5 [ 13.361505] input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input6 [ 13.361576] input: HDA ATI HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input7 [ 13.361653] input: HDA ATI HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input8 [ 13.361731] input: HDA ATI HDMI HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input9 [ 13.361812] input: HDA ATI HDMI HDMI/DP,pcm=11 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input10 [ 13.404451] snd_hda_codec_realtek hdaudioC0D2: autoconfig for ALC888: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line [ 13.404460] snd_hda_codec_realtek hdaudioC0D2: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) [ 13.404463] snd_hda_codec_realtek hdaudioC0D2: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0) [ 13.404466] snd_hda_codec_realtek hdaudioC0D2: mono: mono_out=0x0 [ 13.404468] snd_hda_codec_realtek hdaudioC0D2: dig-out=0x1e/0x0 [ 13.404469] snd_hda_codec_realtek hdaudioC0D2: inputs: [ 13.404472] snd_hda_codec_realtek hdaudioC0D2: Rear Mic=0x18 [ 13.404474] snd_hda_codec_realtek hdaudioC0D2: Front Mic=0x19 [ 13.404476] snd_hda_codec_realtek hdaudioC0D2: Line=0x1a [ 13.404477] snd_hda_codec_realtek hdaudioC0D2: CD=0x1c [ 13.404479] snd_hda_codec_realtek hdaudioC0D2: dig-in=0x1f [ 13.434049] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11 [ 13.434132] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 13.434203] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13 [ 13.434276] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14 [ 13.434348] input: HDA Intel Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15 [ 13.434419] input: HDA Intel Line Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16 [ 13.434485] input: HDA Intel Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input17 [ 13.434555] input: HDA Intel Line Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input18 [ 13.434663] snd_hda_intel 0000:00:1b.0: device 1458:a002 is on the power_save denylist, forcing power_save to 0 [ 13.679720] platform coretemp.0: Using relative temperature scale! [ 13.679746] platform coretemp.0: Using relative temperature scale! [ 13.681357] platform coretemp.0: Using relative temperature scale! [ 13.683882] platform coretemp.0: Using relative temperature scale! [ 13.695729] intel_powerclamp: No package C-state available [ 13.846668] EXT4-fs (sdb1): mounted filesystem 41f667ec-581f-43e4-b1f1-a490372f1365 r/w with ordered data mode. Quota mode: none. [ 13.939844] audit: type=1400 audit(1788188314.526:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="QtWebEngineProcess" pid=771 comm="apparmor_parser" [ 13.940439] audit: type=1400 audit(1788188314.530:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name=4D6F6E676F444220436F6D70617373 pid=770 comm="apparmor_parser" [ 13.940640] audit: type=1400 audit(1788188314.530:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="Discord" pid=769 comm="apparmor_parser" [ 13.944121] audit: type=1400 audit(1788188314.534:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="brave" pid=776 comm="apparmor_parser" [ 13.944238] audit: type=1400 audit(1788188314.534:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="balena-etcher" pid=775 comm="apparmor_parser" [ 13.945739] audit: type=1400 audit(1788188314.534:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="buildah" pid=777 comm="apparmor_parser" [ 13.947642] audit: type=1400 audit(1788188314.534:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="busybox" pid=778 comm="apparmor_parser" [ 13.948213] audit: type=1400 audit(1788188314.538:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="cam" pid=779 comm="apparmor_parser" [ 13.949987] audit: type=1400 audit(1788188314.538:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="ch-checkns" pid=780 comm="apparmor_parser" [ 14.670025] NET: Registered PF_QIPCRTR protocol family [ 14.752180] sky2 0000:05:00.0 enp5s0: enabling interface [ 17.553560] sky2 0000:05:00.0 enp5s0: Link is up at 1000 Mbps, full duplex, flow control both [ 26.996363] rfkill: input handler disabled [ 35.018538] tun: Universal TUN/TAP device driver, 1.6 [ 1445.963720] perf: interrupt took too long (2507 > 2500), lowering kernel.perf_event_max_sample_rate to 79750 [ 2448.935309] perf: interrupt took too long (3137 > 3133), lowering kernel.perf_event_max_sample_rate to 63750 ** Model information sys_vendor: Gigabyte Technology Co., Ltd. product_name: 965P-DS3 product_version: chassis_vendor: Gigabyte Technology Co., Ltd. chassis_version: bios_vendor: Award Software International, Inc. bios_version: F14 board_vendor: Gigabyte Technology Co., Ltd. board_name: 965P-DS3 board_version: x.x ** Configuration for modprobe: blacklist nouveau blacklist arkfb blacklist aty128fb blacklist atyfb blacklist radeonfb blacklist cirrusfb blacklist cyber2000fb blacklist kyrofb blacklist matroxfb_base blacklist mb862xxfb blacklist neofb blacklist pm2fb blacklist pm3fb blacklist s3fb blacklist savagefb blacklist sisfb blacklist tdfxfb blacklist tridentfb blacklist vt8623fb blacklist microcode options snd_pcsp index=-2 options cx88_alsa index=-2 options snd_atiixp_modem index=-2 options snd_intel8x0m index=-2 options snd_via82xx_modem index=-2 options nouveau modeset=0 options bonding max_bonds=0 options dummy numdummies=0 options ifb numifbs=0 ** Loaded modules: xt_nat xt_addrtype tun snd_seq_dummy snd_hrtimer snd_seq snd_seq_device nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip6t_REJECT nf_reject_ipv6 ipt_REJECT nf_reject_ipv4 xt_multiport xt_cgroup xt_mark xt_owner xt_tcpudp nft_compat nf_tables rfkill qrtr binfmt_misc coretemp kvm_intel kvm snd_hda_codec_realtek snd_hda_codec_generic snd_hda_codec_hdmi snd_hda_scodec_component irqbypass snd_hda_intel snd_intel_dspcfg snd_intel_sdw_acpi snd_hda_codec snd_hda_core sha512_ssse3 acpi_cpufreq sha256_ssse3 pcspkr sha1_ssse3 snd_hwdep snd_pcm snd_timer snd soundcore evdev sg msr i2c_dev nvme_fabrics nvme_keyring parport_pc nvme_core ppdev lp nvme_auth parport efi_pstore configfs nfnetlink ip_tables x_tables autofs4 ext4 mbcache jbd2 btrfs blake2b_generic xor raid6_pq libcrc32c crc32c_generic amdgpu drm_buddy amdxcp drm_exec gpu_sched video wmi i2c_algo_bit drm_suballoc_helper drm_display_helper hid_generic cec usbhid rc_core hid sr_mod drm_ttm_helper sd_mod cdrom ttm ata_generic iTCO_wdt uas usb_storage ahci drm_kms_helper uhci_hcd intel_pmc_bxt libahci pata_jmicron xhci_pci iTCO_vendor_support libata drm xhci_hcd watchdog ehci_pci ehci_hcd scsi_mod usbcore crc16 serio_raw i2c_i801 sky2 i2c_smbus scsi_common lpc_ich usb_common button ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 82P965/G965 Memory Controller Hub [8086:29a0] (rev 02) Subsystem: Gigabyte Technology Co., Ltd Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:01.0 PCI bridge [0604]: Intel Corporation 82P965/G965 PCI Express Root Port [8086:29a1] (rev 02) (prog-if 00 [Normal decode]) Subsystem: Gigabyte Technology Co., Ltd Device [1458:5000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 8000-8fff [size=4K] [16-bit] Memory behind bridge: f4000000-f5ffffff [size=32M] [32-bit] Prefetchable memory behind bridge: d0000000-efffffff [size=512M] [32-bit] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA+ VGA16- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1a.0 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 [8086:2834] (rev 02) (prog-if 00 [UHCI]) Subsystem: Gigabyte Technology Co., Ltd Device [1458:5004] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at c000 [size=32] Kernel driver in use: uhci_hcd Kernel modules: uhci_hcd 00:1a.1 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 [8086:2835] (rev 02) (prog-if 00 [UHCI]) Subsystem: Gigabyte Technology Co., Ltd Device [1458:5004] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at c400 [size=32] Kernel driver in use: uhci_hcd Kernel modules: uhci_hcd 00:1a.7 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 [8086:283a] (rev 02) (prog-if 20 [EHCI]) Subsystem: Gigabyte Technology Co., Ltd Device [1458:5006] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 0: Memory at f8204000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci-pci Kernel modules: ehci_pci 00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 02) (prog-if 00 [HDA compatible]) Subsystem: Gigabyte Technology Co., Ltd Device [1458:a002] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 32 Region 0: Memory at f8200000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd_hda_intel 00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 02) (prog-if 00 [Normal decode]) Subsystem: Gigabyte Technology Co., Ltd Device [1458:5001] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 7000-7fff [size=4K] [16-bit] Memory behind bridge: f8300000-f84fffff [size=2M] [32-bit] Prefetchable memory behind bridge: f8500000-f86fffff [size=2M] [32-bit] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- VGA16- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.2 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 [8086:2843] (rev 02) (prog-if 00 [Normal decode]) Subsystem: Gigabyte Technology Co., Ltd Device [1458:5001] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin C routed to IRQ 18 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 1000-1fff [size=4K] [16-bit] Memory behind bridge: f8100000-f81fffff [size=1M] [32-bit] Prefetchable memory behind bridge: f8700000-f88fffff [size=2M] [32-bit] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- VGA16- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.3 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 [8086:2845] (rev 02) (prog-if 00 [Normal decode]) Subsystem: Gigabyte Technology Co., Ltd Device [1458:5001] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin D routed to IRQ 19 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 9000-afff [size=8K] [16-bit] Memory behind bridge: f8000000-f80fffff [size=1M] [32-bit] Prefetchable memory behind bridge: f8900000-f8afffff [size=2M] [32-bit] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- VGA16- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.4 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 [8086:2847] (rev 02) (prog-if 00 [Normal decode]) Subsystem: Gigabyte Technology Co., Ltd Device [1458:5001] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: b000-bfff [size=4K] [16-bit] Memory behind bridge: f6000000-f7ffffff [size=32M] [32-bit] Prefetchable memory behind bridge: f8b00000-f8cfffff [size=2M] [32-bit] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- VGA16- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1d.0 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 [8086:2830] (rev 02) (prog-if 00 [UHCI]) Subsystem: Gigabyte Technology Co., Ltd Device [1458:5004] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 4: I/O ports at c800 [size=32] Kernel driver in use: uhci_hcd Kernel modules: uhci_hcd 00:1d.1 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 [8086:2831] (rev 02) (prog-if 00 [UHCI]) Subsystem: Gigabyte Technology Co., Ltd Device [1458:5004] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at cc00 [size=32] Kernel driver in use: uhci_hcd Kernel modules: uhci_hcd 00:1d.2 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 [8086:2832] (rev 02) (prog-if 00 [UHCI]) Subsystem: Gigabyte Technology Co., Ltd Device [1458:5004] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at d000 [size=32] Kernel driver in use: uhci_hcd Kernel modules: uhci_hcd 00:1d.7 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 [8086:2836] (rev 02) (prog-if 20 [EHCI]) Subsystem: Gigabyte Technology Co., Ltd Device [1458:5006] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at f8205000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci-pci Kernel modules: ehci_pci 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev f2) (prog-if 01 [Subtractive decode]) Subsystem: Gigabyte Technology Co., Ltd Motherboard [1458:5000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=32 I/O behind bridge: 6000-6fff [size=4K] [16-bit] Memory behind bridge: [disabled] [32-bit] Prefetchable memory behind bridge: [disabled] [64-bit] Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- VGA16- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge [0601]: Intel Corporation 82801HB/HR (ICH8/R) LPC Interface Controller [8086:2810] (rev 02) Subsystem: Gigabyte Technology Co., Ltd Device [1458:5001] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: lpc_ich Kernel modules: lpc_ich 00:1f.2 SATA controller [0106]: Intel Corporation 82801HB (ICH8) 4 port SATA Controller [AHCI mode] [8086:2824] (rev 02) (prog-if 01 [AHCI 1.0]) Subsystem: Gigabyte Technology Co., Ltd Device [1458:b005] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 30 Region 0: I/O ports at d400 [size=8] Region 1: I/O ports at d800 [size=4] Region 2: I/O ports at dc00 [size=8] Region 3: I/O ports at e000 [size=4] Region 4: I/O ports at e400 [size=32] Region 5: Memory at f8206000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller [8086:283e] (rev 02) Subsystem: Gigabyte Technology Co., Ltd Device [1458:5001] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 18 Region 0: Memory at f8207000 (32-bit, non-prefetchable) [size=256] Region 4: I/O ports at 0500 [size=32] Kernel driver in use: i801_smbus Kernel modules: i2c_i801 01:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] Ellesmere [Radeon RX 470/480/570/570X/580/580X/590] [1002:67df] (rev c7) (prog-if 00 [VGA controller]) Subsystem: Dell Device [1028:1701] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 31 Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 2: Memory at e0000000 (64-bit, prefetchable) [size=2M] Region 4: I/O ports at 8000 [size=256] Region 5: Memory at f5000000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at 000c0000 [virtual] [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: amdgpu Kernel modules: amdgpu 01:00.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] Ellesmere HDMI Audio [Radeon RX 470/480 / 570/580/590] [1002:aaf0] (prog-if 00 [HDA compatible]) Subsystem: Dell Device [1028:aaf0] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 33 Region 0: Memory at f5040000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd_hda_intel 03:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 04) (prog-if 30 [XHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at f8100000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: xhci_hcd Kernel modules: xhci_pci 04:00.0 SATA controller [0106]: JMicron Technology Corp. JMB363 SATA/IDE Controller [197b:2363] (rev 02) (prog-if 01 [AHCI 1.0]) Subsystem: Gigabyte Technology Co., Ltd Motherboard [1458:b000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 19 Region 5: Memory at f8000000 (32-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: ahci Kernel modules: ahci 04:00.1 IDE interface [0101]: JMicron Technology Corp. JMB363 SATA/IDE Controller [197b:2363] (rev 02) (prog-if 85 [PCI native mode-only controller, supports bus mastering]) Subsystem: Gigabyte Technology Co., Ltd Motherboard [1458:b000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 16 Region 0: I/O ports at 9000 [size=8] Region 1: I/O ports at 9400 [size=4] Region 2: I/O ports at 9800 [size=8] Region 3: I/O ports at 9c00 [size=4] Region 4: I/O ports at a000 [size=16] Capabilities: <access denied> Kernel driver in use: pata_jmicron Kernel modules: pata_jmicron, ata_generic 05:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller [11ab:4364] (rev 12) Subsystem: Gigabyte Technology Co., Ltd Device [1458:e000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 24 Region 0: Memory at f7000000 (64-bit, non-prefetchable) [size=16K] Region 2: I/O ports at b000 [size=256] Expansion ROM at f6000000 [virtual] [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: sky2 Kernel modules: sky2 ** USB devices: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 1307:0330 Transcend Information, Inc. 63-in-1 Multi-Card Reader/Writer Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 002: ID 30fa:0302 Instant USB Optical Mouse -- System Information: Debian Release: 13.6 APT prefers stable-updates APT policy: (500, 'stable-updates'), (500, 'stable-security'), (500, 'stable') Architecture: amd64 (x86_64) Kernel: Linux 6.12.107+deb13-amd64 (SMP w/4 CPU threads; PREEMPT) Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8), LANGUAGE not set Shell: /bin/sh linked to /usr/bin/dash Init: systemd (via /run/systemd/system) LSM: AppArmor: enabled Versions of packages linux-image-6.12.107+deb13-amd64 depends on: ii initramfs-tools [linux-initramfs-tool] 0.148.4 ii kmod 34.2-2 ii linux-base 4.12.1 Versions of packages linux-image-6.12.107+deb13-amd64 recommends: ii apparmor 4.1.0-1 Versions of packages linux-image-6.12.107+deb13-amd64 suggests: pn debian-kernel-handbook <none> pn firmware-linux-free <none> ii grub-pc 2.12-9+deb13u2 pn linux-doc-6.12 <none> Versions of packages linux-image-6.12.107+deb13-amd64 is related to: ii firmware-amd-graphics 20250410-2 pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-cavium <none> pn firmware-cirrus <none> ii firmware-intel-graphics 20250410-2 ii firmware-intel-misc 20250410-2 pn firmware-intel-sound <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> pn firmware-marvell-prestera <none> ii firmware-mediatek 20250410-2 ii firmware-misc-nonfree 20250410-2 pn firmware-myricom <none> pn firmware-netronome <none> pn firmware-netxen <none> pn firmware-nvidia-graphics <none> pn firmware-qcom-soc <none> pn firmware-qlogic <none> pn firmware-realtek <none> pn firmware-samsung <none> pn firmware-siano <none> pn firmware-ti-connectivity <none> pn xen-hypervisor <none> -- no debconf information
Debian GNU/Linux 13.6 (trixie), amd64 GPU: AMD Radeon RX 480 / Polaris10 (PCI 1002:67df), amdgpu Desktop: GNOME/GDM on X11 RustDesk: 1.4.9 Kernel image package Version Result linux-image-6.12.101+deb13-amd64 6.12.101-1 PASS / stable linux-image-6.12.105+deb13-amd64 6.12.105-1 FAIL linux-image-6.12.107+deb13-amd64 6.12.107-1 FAIL 6.12.101 passed repeated native RustDesk interactive sessions, GDM/login and logout/login transitions, sustained sessions, reconnects, and a final 7,201-second unattended monitor (1,355 samples) with zero VCE timeout, GPU reset, VRAM-loss, or graphical-session teardown events. 6.12.105 failed with both Flatpak RustDesk 1.4.9 and the official native RustDesk 1.4.9 Debian package/system service. A controlled native-service session failed after approximately 30 seconds. 6.12.107 failed with the official native RustDesk package/system service after approximately 15 seconds of active remote use. This run crossed the test stop boundary at VCE timeout and GPU reset; it did not record VRAM loss or full X11 teardown.
Representative native RustDesk 1.4.9 failure on kernel 6.12.105+deb13-amd64 (Debian package linux-image-6.12.105+deb13-amd64 6.12.105-1): 2026-08-29T19:52:24.358108-05:00 kernel: amdgpu 0000:01:00.0: amdgpu: ring vce0 timeout, signaled seq=63, emitted seq=64 2026-08-29T19:52:24.358695-05:00 kernel: amdgpu 0000:01:00.0: amdgpu: Process information: process rustdesk pid 4790 thread rustdesk:cs0 pid 7411 2026-08-29T19:52:24.359279-05:00 kernel: amdgpu 0000:01:00.0: amdgpu: GPU reset begin! 2026-08-29T19:52:28.355761-05:00 kernel: amdgpu 0000:01:00.0: amdgpu: failed to suspend display audio 2026-08-29T19:52:28.471776-05:00 kernel: [drm:amdgpu_device_ip_suspend_phase2 [amdgpu]] *ERROR* suspend of IP block <vce_v3_0> failed -22 2026-08-29T19:52:28.743751-05:00 kernel: amdgpu 0000:01:00.0: amdgpu: GPU reset succeeded, trying to resume 2026-08-29T19:52:28.744249-05:00 kernel: [drm] VRAM is lost due to GPU reset! 2026-08-29T19:52:29.072931-05:00 kernel: amdgpu 0000:01:00.0: amdgpu: GPU reset(1) succeeded! 2026-08-29T19:52:29.070572-05:00 rustdesk[4790]: amdgpu: The CS has cancelled because the context is lost. This context is innocent. 2026-08-29T19:52:30.173371-05:00 gdm-x-session[2484]: amdgpu: The CS has cancelled because the context is lost. This context is innocent. 2026-08-29T19:52:30.186144-05:00 gnome-shell[3990]: X connection to :0 broken (explicit kill or server shutdown). 2026-08-29T19:52:31.813759-05:00 rustdesk[7868]: cannot open display: :0 2026-08-29T19:52:32.253828-05:00 gdm-autologin][2232]: pam_unix(gdm-autologin:session): session closed for user <local-user> Flatpak RustDesk independently produced the same kernel sequence on this kernel. That second reproduction is summarized in the main report; it is not necessary to publish duplicate process/session details here.
Official native RustDesk 1.4.9 failure on kernel 6.12.107+deb13-amd64 (Debian package linux-image-6.12.107+deb13-amd64 6.12.107-1): 2026-08-30T07:39:33.441804-05:00 kernel: amdgpu 0000:01:00.0: amdgpu: ring vce0 timeout, signaled seq=127, emitted seq=128 2026-08-30T07:39:33.442209-05:00 kernel: amdgpu 0000:01:00.0: amdgpu: Process information: process rustdesk pid 4670 thread rustdesk:cs0 pid 21229 2026-08-30T07:39:33.442595-05:00 kernel: amdgpu 0000:01:00.0: amdgpu: GPU reset begin! 2026-08-30T07:39:37.440740-05:00 kernel: amdgpu 0000:01:00.0: amdgpu: failed to suspend display audio 2026-08-30T07:39:37.441992-05:00 kernel: amdgpu 0000:01:00.0: amdgpu: GPU reset(1) succeeded! The RustDesk connection froze after approximately 15 seconds. This test was stopped at the predetermined failure boundary. Unlike the severe 6.12.105 run, this particular 6.12.107 run did not record VRAM loss or full X11/GNOME teardown.
