Package: linux-image-2.6.18-4-686 Version: 2.6.18.dfsg.1-10 Severity: important
All the versions of linux-image-2.6.18-*-686 that I have tried normally hang when booting on my Sony Vaio PCG-Z600LEK. Last time I had to boot 4 times before the machine booted correctly. I have to poweroff between each boot attempt. linux-image-2.6.16-2-686 boots everytime. The first time the boot hung after these lines: PIIX4 devres I PIO at 0398-0399 PIIX4 devres J PIO at 0398-0399 ACPI: Embedded Controller [EC0] (gpe 9) interrupt mode The second time it hung after: ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 The third time it hung after: Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init When the machine booted correctly (on the 4th attempt) dmesg said BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e8400 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000003ff0000 (usable) BIOS-e820: 0000000003ff0000 - 0000000003fff800 (ACPI data) BIOS-e820: 0000000003fff800 - 0000000004000000 (ACPI NVS) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 63MB LOWMEM available. On node 0 totalpages: 16368 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 12272 pages, LIFO batch:1 DMI 2.1 present. ACPI: RSDP (v000 SONY ) @ 0x000f6bb0 ACPI: RSDT (v001 SONY Z3 0x20001225 PTL 0x00000000) @ 0x03ffc1ca ACPI: FADT (v001 SONY Z3 0x20001225 PTL 0x000f4240) @ 0x03fff764 ACPI: BOOT (v001 SONY Z3 0x20001225 PTL 0x00000001) @ 0x03fff7d8 ACPI: DSDT (v001 SONY Z3 0x20001225 MSFT 0x01000007) @ 0x00000000 ACPI: PM-Timer IO Port: 0x8008 Allocating PCI resources starting at 10000000 (gap: 04000000:fbf80000) Detected 694.900 MHz processor. Built 1 zonelists. Total pages: 16368 Kernel command line: root=/dev/hda2 ro Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffd000 (01089000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 256 (order: 8, 1024 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 57068k/65472k available (1544k kernel code, 7996k reserved, 577k data, 196k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 1390.86 BogoMIPS (lpj=2781723) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 16k freed ACPI: Core revision 20060707 CPU0: Intel Pentium III (Coppermine) stepping 06 SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. Brought up 1 CPUs migration_cost=0 checking if image is initramfs... it is Freeing initrd memory: 4746k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd9ae, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI quirk: region 8000-803f claimed by PIIX4 ACPI PCI quirk: region 1040-104f claimed by PIIX4 SMB PIIX4 devres I PIO at 0398-0399 PIIX4 devres J PIO at 0398-0399 PCI: Firmware left 0000:00:0b.0 e100 interrupts enabled, disabling Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: Embedded Controller [EC0] (gpe 9) interrupt mode. ACPI: PCI Interrupt Link [LNKA] (IRQs *9) ACPI: PCI Interrupt Link [LNKB] (IRQs 9) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 9) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 9) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 11 devices PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:01: ioport range 0x398-0x399 has been reserved pnp: 00:01: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:01: ioport range 0x1040-0x104f has been reserved pnp: 00:01: ioport range 0x8000-0x804f could not be reserved PCI: Bridge: 0000:00:01.0 IO window: e000-efff MEM window: fd000000-febfffff PREFETCH window: 14000000-140fffff PCI: Bus 2, cardbus bridge: 0000:00:0c.0 IO window: 00001400-000014ff IO window: 00001800-000018ff PREFETCH window: 10000000-11ffffff MEM window: 12000000-13ffffff ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9 PCI: setting IRQ 9 as level-triggered ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9 PCI: Setting latency timer of device 0000:00:0c.0 to 64 ... ACPI: (supports S0<6>Time: tsc clocksource has been installed. S1 S3 S4 S5) Freeing unused kernel memory: 196k freed input: AT Translated Set 2 keyboard as /class/input/input0 ACPI: CPU0 (power states: C1[C1] C2[C2]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: Thermal Zone [ATF0] (51 C) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PIIX4: IDE controller at PCI slot 0000:00:07.1 PIIX4: chipset revision 1 PIIX4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xfcb0-0xfcb7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xfcb8-0xfcbf, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... ieee1394: Initialized config rom entry `ip1394' usbcore: registered new driver usbfs usbcore: registered new driver hub e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI e100: Copyright(c) 1999-2005 Intel Corporation USB Universal Host Controller Interface driver v3.0 hda: HITACHI_DK23BA-15, ATA DISK drive Time: acpi_pm clocksource has been installed. ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... PCI: Enabling device 0000:00:08.0 (0000 -> 0002) ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9 ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[9] MMIO=[fecfe000-fecfe7ff] Max Packet=[2048] IR/IT contexts=[4/4] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9 ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9 e100: eth0: e100_probe: addr 0xfecff000, irq 9, MAC addr 08:00:46:0E:B7:96 ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9 ... PCI: Enabling device 0000:00:09.0 (0006 -> 0007) ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 9 ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9 ... ACPI: Battery Slot [BAT1] (battery present) ACPI: AC Adapter [ACAD] (on-line) ACPI: Power Button (CM) [PWRB] -- System Information: Debian Release: 4.0 APT prefers unstable APT policy: (990, 'unstable'), (500, 'testing'), (500, 'stable') Architecture: i386 (i686) Shell: /bin/sh linked to /bin/bash Kernel: Linux 2.6.18-4-686 Locale: LANG=C, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8) Versions of packages linux-image-2.6.18-4-686 depends on: ii coreutils 5.97-5.3 The GNU core utilities ii debconf [debconf-2.0] 1.5.11 Debian configuration management sy ii initramfs-tools [linux-initra 0.85e tools for generating an initramfs ii module-init-tools 3.3-pre4-1 tools for managing Linux kernel mo Versions of packages linux-image-2.6.18-4-686 recommends: pn libc6-i686 <none> (no description available) -- debconf information: linux-image-2.6.18-4-686/preinst/failed-to-move-modules-2.6.18-4-686: linux-image-2.6.18-4-686/preinst/lilo-initrd-2.6.18-4-686: true shared/kernel-image/really-run-bootloader: true linux-image-2.6.18-4-686/preinst/elilo-initrd-2.6.18-4-686: true linux-image-2.6.18-4-686/preinst/overwriting-modules-2.6.18-4-686: true linux-image-2.6.18-4-686/prerm/removing-running-kernel-2.6.18-4-686: true linux-image-2.6.18-4-686/prerm/would-invalidate-boot-loader-2.6.18-4-686: true linux-image-2.6.18-4-686/postinst/bootloader-test-error-2.6.18-4-686: linux-image-2.6.18-4-686/preinst/abort-overwrite-2.6.18-4-686: linux-image-2.6.18-4-686/postinst/old-system-map-link-2.6.18-4-686: true linux-image-2.6.18-4-686/postinst/depmod-error-2.6.18-4-686: false linux-image-2.6.18-4-686/preinst/abort-install-2.6.18-4-686: linux-image-2.6.18-4-686/preinst/lilo-has-ramdisk: linux-image-2.6.18-4-686/postinst/bootloader-error-2.6.18-4-686: linux-image-2.6.18-4-686/postinst/depmod-error-initrd-2.6.18-4-686: false linux-image-2.6.18-4-686/postinst/old-initrd-link-2.6.18-4-686: true linux-image-2.6.18-4-686/preinst/bootloader-initrd-2.6.18-4-686: true linux-image-2.6.18-4-686/preinst/already-running-this-2.6.18-4-686: linux-image-2.6.18-4-686/preinst/initrd-2.6.18-4-686: linux-image-2.6.18-4-686/postinst/create-kimage-link-2.6.18-4-686: true linux-image-2.6.18-4-686/postinst/old-dir-initrd-link-2.6.18-4-686: true linux-image-2.6.18-4-686/postinst/kimage-is-a-directory: -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]