--- Begin Message ---
Package: linux-image-2.6.22-3-amd64
Version: 2.6.22-6
Severity: important
Hi,
Console reported an error during NCQ on Samnung sata HDD (configured in bios
with AHCI).
Below you will find:
1. error recorded in dmesg
2. dmesg shows at beginning
3. sdparm -a /dev/sda
4. smartctl -a /dev/sda
5. uname -a
6. motherboard gigabyte GA-P35-DS4
/var/log/ shows it happened 2 times only since beginning November 2007.
I wonder if such error corrupt hdd data or not.
Thanks for your efforts on this bug.
Franck
### 1. error recorded in dmesg ###
...
ata1.00: exception Emask 0x2 SAct 0x3 SErr 0x0 action 0x2 frozen
ata1.00: (spurious completions during NCQ issue=0x0 SAct=0x3
FIS=004040a1:00000002)
ata1.00: cmd 60/01:00:a2:10:13/00:00:13:00:00/40 tag 0 cdb 0x0 data 512 in
res 40/00:0c:a3:10:13/00:00:13:00:00/40 Emask 0x2 (HSM violation)
ata1.00: cmd 60/07:08:a3:10:13/00:00:13:00:00/40 tag 1 cdb 0x0 data 3584 in
res 40/00:0c:a3:10:13/00:00:13:00:00/40 Emask 0x2 (HSM violation)
ata1: soft resetting port
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: configured for UDMA/133
ata1: EH complete
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
...
### 2. dmesg shows at beginning ###
Linux version 2.6.22-3-amd64 (Debian 2.6.22-6) ([EMAIL PROTECTED]) (gcc version
4.1.3 20071019 (prerelease) (Debian 4.1.2-17)) #1 SMP Sun Nov 4 18:18:09 UTC
2007
Command line: root=/dev/sda6 ro quiet irqpoll nolapic
...
ata1.00: ATA-8: SAMSUNG HD501LJ, CR100-10, max UDMA7
ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
...
### 3. sdparm -a /dev/sda ###
/dev/sda: ATA SAMSUNG HD501LJ CR10
Read write error recovery mode page:
AWRE 1
ARRE 1
TB 0
RC 0
EER 0
PER 0
DTE 0
DCR 0
RRC 0
COR_S 0
HOC 0
DSOC 0
WRC 0
RTL 0
Caching (SBC) mode page:
IC 0
ABPF 0
CAP 0
DISC 0
SIZE 0
WCE 1
MF 0
RCD 0
DRRP 0
WRP 0
DPTL 0
MIPF 0
MAPF 0
MAPFC 0
FSW 0
LBCSS 0
DRA 0
NV_DIS 0
NCS 0
CSS 0
Control mode page:
TST 0
TMF_ONLY 0
D_SENSE 0
GLTSD 1
RLEC 0
QAM 0
QERR 0
RAC 0
UA_INTLCK 0
SWP 0
ATO 0
TAS 0
AUTOLOAD 0
BTP -1
ESTCT 30
### 4. smartctl -a /dev/sda ###
smartctl version 5.37 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce
Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG HD501LJ
Serial Number: S0MUJ13P621xxx (xxx=deleted)
Firmware Version: CR100-10
User Capacity: 500,107,862,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Not recognized. Minor revision code: 0x52
...
### 5. uname -a ###
Linux dualian 2.6.22-3-amd64 #1 SMP Sun Nov 4 18:18:09 UTC 2007 x86_64 GNU/Linux
### 6. motherboard gigabyte GA-P35-DS4 ###
using P35 intel chipset
http://www.gigabyte.com.tw/Products/Motherboard/Products_Overview.aspx?ClassValue=Motherboard&ProductID=2638&ProductName=GA-P35-DS4
-- Package-specific info:
** Version:
Linux version 2.6.22-3-amd64 (Debian 2.6.22-6) ([EMAIL PROTECTED]) (gcc version
4.1.3 20071019 (prerelease) (Debian 4.1.2-17)) #1 SMP Sun Nov 4 18:18:09 UTC
2007
** Not tainted
** Kernel log:
ata7: SATA link down (SStatus 0 SControl 300)
ata8: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt 0000:05:06.0[A] -> Link [LNKC] -> GSI 14 (level, low) ->
IRQ 14
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sda: sda1 sda2 <<5>firewire_ohci: Added fw-ohci device 0000:05:06.0, OHCI
version 1.10
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [LNKB] -> GSI 15 (level, low) ->
IRQ 15
PCI: Setting latency timer of device 0000:04:00.0 to 64
ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNK1] -> GSI 5 (level, low) -> IRQ
5
eth0: RTL8168b/8111b at 0xffffc20000332000, 00:1a:4d:45:cd:95, IRQ 15
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 5, io mem 0xf8204000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb8: configuration #1 chosen from 1 choice
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 6 ports detected
sda5<6>udev: renamed network interface eth0 to eth1
sda6 sda7 sda8 sda9 >
sd 0:0:0:0: [sda] Attached SCSI disk
sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sdb:<6>JMB363: IDE controller at PCI slot 0000:03:00.1
ACPI: PCI Interrupt 0000:03:00.1[B] -> Link [LNKB] -> GSI 15 (level, low) ->
IRQ 15
JMB363: chipset revision 2
JMB363: 100% native mode on irq 15
ide0: BM-DMA at 0xc400-0xc407, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xc408-0xc40f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
sdb1 sdb2
sd 1:0:0:0: [sdb] Attached SCSI disk
firewire_core: created new fw device fw0 (0 config rom retries)
hda: SAMSUNG CD-R/RW SW-248F, ATAPI CD/DVD-ROM drive
hda: selected mode 0x42
ide0 at 0xc000-0xc007,0xc102 on irq 15
Probing IDE interface ide1...
hda: ATAPI 48X CD-ROM CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
swsusp: Marking nosave pages: 000000000009e000 - 0000000000100000
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
pnp: the driver 'parport_pc' has been registered
pnp: match found with the PnP device '00:07' and the driver 'parport_pc'
parport_pc 00:07: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
input: PC Speaker as /class/input/input2
ACPI: PCI Interrupt 0000:00:1f.3[C] -> Link [LNKC] -> GSI 14 (level, low) ->
IRQ 14
ACPI: PCI Interrupt Link [LNK0] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNK0] -> GSI 12 (level, low) ->
IRQ 12
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
EXT3 FS on sda6, internal journal
loop: module loaded
it87: Found IT8718F chip at 0x290, revision 4
it87: in3 is VCC (+5V)
coretemp coretemp.0: Using undocumented features, absolute temperature might be
wrong!
coretemp coretemp.1: Using undocumented features, absolute temperature might be
wrong!
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [EMAIL PROTECTED]
fuse init (API version 7.8)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1060248k swap on /dev/mapper/sda7. Priority:-1 extents:1 across:1060248k
r8169: eth1: link up
r8169: eth1: link up
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) ->
IRQ 11
[drm] Initialized radeon 1.27.0 20060524 on minor 0
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode
[drm] writeback test succeeded in 1 usecs
eth1: no IPv6 routers present
hda: cdrom_pc_intr: The drive appears confused (ireason = 0x01). Trying to
recover by ending request.
** Loaded modules:
Module Size Used by
radeon 123296 2
drm 100776 3 radeon
ppdev 13704 0
lp 17352 0
button 13472 0
ac 10376 0
battery 15496 0
ipv6 296840 12
acpi_cpufreq 13704 0
cpufreq_stats 10400 0
cpufreq_powersave 6272 0
cpufreq_conservative 12424 0
cpufreq_ondemand 13328 2
freq_table 9600 3 acpi_cpufreq,cpufreq_stats,cpufreq_ondemand
cpufreq_userspace 9472 0
fuse 50608 1
aes 30912 1
cbc 9088 1
blkcipher 10884 1 cbc
dm_crypt 18192 1
dm_snapshot 21704 0
dm_mirror 26240 0
dm_mod 64112 5 dm_crypt,dm_snapshot,dm_mirror
coretemp 12544 0
it87 27408 0
hwmon_vid 7296 1 it87
i2c_isa 9344 1 it87
firewire_sbp2 18180 0
loop 23044 0
snd_hda_intel 311968 1
snd_pcm_oss 48288 0
snd_mixer_oss 21376 1 snd_pcm_oss
snd_pcm 89992 2 snd_hda_intel,snd_pcm_oss
snd_timer 28424 1 snd_pcm
snd 65896 7
snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
i2c_i801 13468 0
pcspkr 7680 0
parport_pc 42664 1
parport 44428 3 ppdev,lp,parport_pc
i2c_core 31488 3 it87,i2c_isa,i2c_i801
soundcore 13088 1 snd
snd_page_alloc 15376 2 snd_hda_intel,snd_pcm
intel_agp 32032 0
tsdev 13312 0
evdev 15232 3
ext3 137232 2
jbd 68080 1 ext3
mbcache 13832 1 ext3
ide_cd 44832 0
cdrom 39848 1 ide_cd
jmicron 8576 0 [permanent]
sd_mod 33280 4
generic 10372 0 [permanent]
ide_core 147728 3 ide_cd,jmicron,generic
usbhid 32704 0
hid 31360 1 usbhid
firewire_ohci 22784 0
firewire_core 49728 2 firewire_sbp2,firewire_ohci
crc_itu_t 6656 1 firewire_core
r8169 36488 0
ata_generic 13188 0
ahci 28804 3
libata 132528 2 ata_generic,ahci
scsi_mod 164536 3 firewire_sbp2,sd_mod,libata
ehci_hcd 37900 0
uhci_hcd 29856 0
thermal 19600 0
processor 39912 2 acpi_cpufreq,thermal
fan 9992 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Unknown device [8086:29c0] (rev
02)
Subsystem: Giga-byte Technology Unknown device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation Unknown device [8086:29c1] (rev
02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: f4000000-f5ffffff
Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1a.0 USB Controller [0c03]: Intel Corporation Unknown device [8086:2937]
(rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at e100 [size=32]
Capabilities: <access denied>
00:1a.1 USB Controller [0c03]: Intel Corporation Unknown device [8086:2938]
(rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 3
Region 4: I/O ports at e200 [size=32]
Capabilities: <access denied>
00:1a.2 USB Controller [0c03]: Intel Corporation Unknown device [8086:2939]
(rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 14
Region 4: I/O ports at e000 [size=32]
Capabilities: <access denied>
00:1a.7 USB Controller [0c03]: Intel Corporation Unknown device [8086:293c]
(rev 02) (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 14
Region 0: Memory at f8205000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation Unknown device [8086:293e] (rev
02)
Subsystem: Giga-byte Technology Unknown device [1458:a022]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 12
Region 0: Memory at f8200000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
00:1c.0 PCI bridge [0604]: Intel Corporation Unknown device [8086:2940] (rev
02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1c.4 PCI bridge [0604]: Intel Corporation Unknown device [8086:2948] (rev
02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f8000000-f80fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1c.5 PCI bridge [0604]: Intel Corporation Unknown device [8086:294a] (rev
02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f6000000-f7ffffff
Prefetchable memory behind bridge: 0000000080000000-00000000800fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1d.0 USB Controller [0c03]: Intel Corporation Unknown device [8086:2934]
(rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 4: I/O ports at e300 [size=32]
Capabilities: <access denied>
00:1d.1 USB Controller [0c03]: Intel Corporation Unknown device [8086:2935]
(rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at e400 [size=32]
Capabilities: <access denied>
00:1d.2 USB Controller [0c03]: Intel Corporation Unknown device [8086:2936]
(rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 14
Region 4: I/O ports at e500 [size=32]
Capabilities: <access denied>
00:1d.7 USB Controller [0c03]: Intel Corporation Unknown device [8086:293a]
(rev 02) (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f8204000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
92) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
Memory behind bridge: f8100000-f81fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation Unknown device [8086:2916] (rev 02)
Subsystem: Giga-byte Technology Unknown device [1458:5001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation Unknown device [8086:2922]
(rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Giga-byte Technology Unknown device [1458:b005]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 1275
Region 0: I/O ports at e600 [size=8]
Region 1: I/O ports at e700 [size=4]
Region 2: I/O ports at e800 [size=8]
Region 3: I/O ports at e900 [size=4]
Region 4: I/O ports at ea00 [size=32]
Region 5: Memory at f8206000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
00:1f.3 SMBus [0c05]: Intel Corporation Unknown device [8086:2930] (rev 02)
Subsystem: Giga-byte Technology Unknown device [1458:5001]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 14
Region 0: Memory at f8207000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0500 [size=32]
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc R430 [Radeon
X800 (PCIE)] [1002:554f] (prog-if 00 [VGA])
Subsystem: Hightech Information System Ltd. Unknown device [1787:154f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at f5000000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at b000 [size=256]
[virtual] Expansion ROM at f4000000 [disabled] [size=128K]
Capabilities: <access denied>
01:00.1 Display controller [0380]: ATI Technologies Inc R430 [Radeon X800
(PCIE) Secondary] [1002:556f]
Subsystem: Hightech Information System Ltd. Unknown device [1787:154e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Region 0: Memory at f5010000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
03:00.0 SATA controller [0106]: JMicron Technologies, Inc. JMicron 20360/20363
AHCI Controller [197b:2363] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Giga-byte Technology Unknown device [1458:b000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 5: Memory at f8000000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
03:00.1 IDE interface [0101]: JMicron Technologies, Inc. JMicron 20360/20363
AHCI Controller [197b:2363] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Giga-byte Technology Unknown device [1458:b000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 15
Region 0: I/O ports at c000 [size=8]
Region 1: I/O ports at c100 [size=4]
Region 2: I/O ports at c200 [size=8]
Region 3: I/O ports at c300 [size=4]
Region 4: I/O ports at c400 [size=16]
Capabilities: <access denied>
04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01)
Subsystem: Giga-byte Technology Unknown device [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 15
Region 0: I/O ports at d000 [size=256]
Region 2: Memory at f7000000 (64-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 80000000 [disabled] [size=64K]
Capabilities: <access denied>
05:06.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23
IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Unknown device [1458:1000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 14
Region 0: Memory at f8104000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at f8100000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
-- System Information:
Debian Release: lenny/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.22-3-amd64 (SMP w/2 CPU cores)
Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.22-3-amd64 depends on:
ii e2fsprogs 1.40.2-1 ext2 file system utilities and lib
ii initramfs-tools [linux-initr 0.91c tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo
linux-image-2.6.22-3-amd64 recommends no packages.
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.22-3-amd64/postinst/create-kimage-link-2.6.22-3-amd64: true
linux-image-2.6.22-3-amd64/postinst/depmod-error-initrd-2.6.22-3-amd64: false
linux-image-2.6.22-3-amd64/prerm/would-invalidate-boot-loader-2.6.22-3-amd64:
true
linux-image-2.6.22-3-amd64/postinst/old-system-map-link-2.6.22-3-amd64: true
linux-image-2.6.22-3-amd64/preinst/overwriting-modules-2.6.22-3-amd64: true
linux-image-2.6.22-3-amd64/preinst/failed-to-move-modules-2.6.22-3-amd64:
linux-image-2.6.22-3-amd64/postinst/depmod-error-2.6.22-3-amd64: false
linux-image-2.6.22-3-amd64/prerm/removing-running-kernel-2.6.22-3-amd64: true
linux-image-2.6.22-3-amd64/postinst/bootloader-error-2.6.22-3-amd64:
linux-image-2.6.22-3-amd64/preinst/abort-overwrite-2.6.22-3-amd64:
* linux-image-2.6.22-3-amd64/preinst/already-running-this-2.6.22-3-amd64:
linux-image-2.6.22-3-amd64/postinst/bootloader-test-error-2.6.22-3-amd64:
linux-image-2.6.22-3-amd64/postinst/old-initrd-link-2.6.22-3-amd64: true
linux-image-2.6.22-3-amd64/preinst/bootloader-initrd-2.6.22-3-amd64: true
linux-image-2.6.22-3-amd64/preinst/lilo-initrd-2.6.22-3-amd64: true
linux-image-2.6.22-3-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.22-3-amd64/preinst/abort-install-2.6.22-3-amd64:
linux-image-2.6.22-3-amd64/preinst/elilo-initrd-2.6.22-3-amd64: true
linux-image-2.6.22-3-amd64/postinst/old-dir-initrd-link-2.6.22-3-amd64: true
linux-image-2.6.22-3-amd64/preinst/initrd-2.6.22-3-amd64:
linux-image-2.6.22-3-amd64/postinst/kimage-is-a-directory:
--- End Message ---
