Package: Unknown Version Unknown Hi,
Description: Connect Sony W980 phone to up to date Lenny as at 17/11/2008. It does not detect and auto mount in the Gnome (2.22) desktop (clean install from Debian installer RC1 DVD followed by online update to 17/11/08). The phone's mass storage worked from Etch installation around one week previously. Possible packages affected: hal 0.5.11-6 linux-image-2.6.26-1-686 2.6.26-8 libc6-i686 2.7-16 Snip from dmesg - connecting phone, selecting mass storage and then disconnecting. [ 504.224151] usb 3-6: new high speed USB device using ehci_hcd and address 2 [ 504.920374] usb 3-6: configuration #2 chosen from 1 choice [ 504.924358] usb 3-6: New USB device found, idVendor=0fce, idProduct=e0da [ 504.924368] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 504.924372] usb 3-6: Product: Memory Stick [ 504.924374] usb 3-6: Manufacturer: Sony Ericsson [ 504.924377] usb 3-6: SerialNumber: 3553530229124830 [ 505.063405] Initializing USB Mass Storage driver... [ 505.070561] scsi0 : SCSI emulation for USB Mass Storage devices [ 505.074078] usbcore: registered new interface driver usb-storage [ 505.074087] USB Mass Storage support registered. [ 505.115660] usb-storage: device found at 2 [ 505.115671] usb-storage: waiting for device to settle before scanning [ 510.112411] usb-storage: device scan complete [ 510.113138] scsi 0:0:0:0: Direct-Access Sony Eri Memory Stick 0 PQ: 0 ANSI: 0 [ 510.199960] Driver 'sd' needs updating - please use bus_type methods [ 510.202825] sd 0:0:0:0: [sda] 15520084 512-byte hardware sectors (7946 MB) [ 510.206261] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled [ 510.206271] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 510.208369] sd 0:0:0:0: [sda] 15520084 512-byte hardware sectors (7946 MB) [ 510.209626] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled [ 510.209634] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 510.209640] sda: sda1 [ 510.212601] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 540.528018] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 570.780020] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 601.068022] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 631.336020] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 661.644021] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 691.912036] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 692.111295] sd 0:0:0:0: [sda] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK,SUGGEST_OK [ 692.111308] end_request: I/O error, dev sda, sector 15520064 [ 692.111314] Buffer I/O error on device sda, logical block 3880016 [ 722.224020] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 752.492036] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 782.796021] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 813.100020] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 843.400021] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 871.880071] INFO: task vol_id:4543 blocked for more than 120 seconds. [ 871.880080] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 871.880084] vol_id D d73b4dbf 0 4543 1 [ 871.880089] f6a38dc0 00000082 f6ba0000 d73b4dbf 00000076 f6a38f4c c180bfa0 00000000 [ 871.880097] f70403fc 0005d342 0000254c 00000000 0005d342 f70403fc 0005d342 c1801a60 [ 871.880103] c180bfa0 01453000 c1801a60 c0157e7b c02b8040 f6b99e50 f6b99e50 c0156729 [ 871.880110] Call Trace: [ 871.880149] [<c0157e7b>] sync_page_killable+0x0/0x2a [ 871.880162] [<c02b8040>] io_schedule+0x49/0x80 [ 871.880171] [<c0156729>] sync_page+0x33/0x36 [ 871.880176] [<c0157e80>] sync_page_killable+0x5/0x2a [ 871.880180] [<c02b816c>] __wait_on_bit_lock+0x2a/0x52 [ 871.880188] [<c0156694>] __lock_page_killable+0x51/0x57 [ 871.880196] [<c01317a9>] wake_bit_function+0x0/0x3c [ 871.880205] [<c015830e>] generic_file_aio_read+0x331/0x4da [ 871.880226] [<c017407f>] do_sync_read+0xbf/0xfe [ 871.880244] [<c013177c>] autoremove_wake_function+0x0/0x2d [ 871.880252] [<c01660d7>] vma_merge+0xd3/0x142 [ 871.880267] [<c01b92c3>] security_file_permission+0xc/0xd [ 871.880276] [<c0173fc0>] do_sync_read+0x0/0xfe [ 871.880281] [<c0174807>] vfs_read+0x81/0x11e [ 871.880288] [<c0174c58>] sys_read+0x3c/0x63 [ 871.880296] [<c0103853>] sysenter_past_esp+0x78/0xb1 [ 871.880315] ======================= [ 873.664033] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 873.817233] sd 0:0:0:0: [sda] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK,SUGGEST_OK [ 873.817242] end_request: I/O error, dev sda, sector 15520068 [ 873.817248] Buffer I/O error on device sda, logical block 3880017 [ 903.980050] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 934.248034] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 964.508018] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 994.776020] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 1025.044019] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 1055.312062] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 1055.470811] sd 0:0:0:0: [sda] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK,SUGGEST_OK [ 1055.470825] end_request: I/O error, dev sda, sector 15520064 [ 1055.470831] Buffer I/O error on device sda, logical block 3880016 [ 1055.470837] Buffer I/O error on device sda, logical block 3880017 [ 1085.708063] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 1115.976019] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 1146.244022] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 1176.512055] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 1206.776032] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 1237.040030] usb 3-6: reset high speed USB device using ehci_hcd and address 2 [ 1237.192237] sd 0:0:0:0: [sda] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK,SUGGEST_OK [ 1237.192250] end_request: I/O error, dev sda, sector 15520080 [ 1675.732007] usb 3-6: USB disconnect, address 2 [ 2116.348069] INFO: task vol_id:4543 blocked for more than 120 seconds. [ 2116.348080] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 2116.348084] vol_id D befa4082 0 4543 1 [ 2116.348089] f6a38dc0 00000082 c16d7540 befa4082 000000f5 f6a38f4c c180bfa0 00000000 [ 2116.348097] f70403fc 000c013e 0002a375 00000000 000c013e f70403fc 000c013e c18016a0 [ 2116.348104] c180bfa0 01453000 c18016a0 c0157e7b c02b8040 f6b99e50 f6b99e50 c0156729 [ 2116.348110] Call Trace: [ 2116.348150] [<c0157e7b>] sync_page_killable+0x0/0x2a [ 2116.348162] [<c02b8040>] io_schedule+0x49/0x80 [ 2116.348172] [<c0156729>] sync_page+0x33/0x36 [ 2116.348176] [<c0157e80>] sync_page_killable+0x5/0x2a [ 2116.348181] [<c02b816c>] __wait_on_bit_lock+0x2a/0x52 [ 2116.348189] [<c0156694>] __lock_page_killable+0x51/0x57 [ 2116.348196] [<c01317a9>] wake_bit_function+0x0/0x3c [ 2116.348206] [<c015830e>] generic_file_aio_read+0x331/0x4da [ 2116.348227] [<c017407f>] do_sync_read+0xbf/0xfe [ 2116.348245] [<c013177c>] autoremove_wake_function+0x0/0x2d [ 2116.348255] [<f89381c1>] end_unlink_async+0x46/0xcd [ehci_hcd] [ 2116.348271] [<c01b92c3>] security_file_permission+0xc/0xd [ 2116.348280] [<c0173fc0>] do_sync_read+0x0/0xfe [ 2116.348285] [<c0174807>] vfs_read+0x81/0x11e [ 2116.348293] [<c0174c58>] sys_read+0x3c/0x63 [ 2116.348301] [<c0103853>] sysenter_past_esp+0x78/0xb1 [ 2116.348319] ======================= Hardware: Snip from dmesg - please let me know if you need more information: [ 0.084089] Calibrating delay using timer specific routine.. 3611.63 BogoMIPS (lpj=7223271) [ 0.084262] Security Framework initialized [ 0.084334] SELinux: Disabled at boot. [ 0.084400] Capability LSM initialized [ 0.084482] Mount-cache hash table entries: 512 [ 0.084743] Initializing cgroup subsys ns [ 0.084810] Initializing cgroup subsys cpuacct [ 0.084875] Initializing cgroup subsys devices [ 0.084961] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 0.085031] CPU: L2 Cache: 256K (64 bytes/line) [ 0.085098] Intel machine check architecture supported. [ 0.085164] Intel machine check reporting enabled on CPU#0. [ 0.085245] Checking 'hlt' instruction... OK. [ 0.100351] SMP alternatives: switching to UP code [ 0.108241] Freeing SMP alternatives: 16k freed [ 0.108312] ACPI: Core revision 20080321 [ 0.124007] ENABLING IO-APIC IRQs [ 0.124007] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 [ 0.163753] CPU0: AMD Athlon(tm) XP 2200+ stepping 01 [ 0.164010] Brought up 1 CPUs [ 0.164010] Total of 1 processors activated (3611.63 BogoMIPS). [ 0.164010] CPU0 attaching sched-domain: [ 0.164010] domain 0: span 0 [ 0.164010] groups: 0 [ 0.164010] net_namespace: 660 bytes [ 0.164010] Booting paravirtualized kernel on bare hardware [ 0.164010] NET: Registered protocol family 16 [ 0.164010] ACPI: bus type pci registered [ 0.220013] PCI: PCI BIOS revision 2.10 entry at 0xfb4c0, last bus=2 [ 0.220013] PCI: Using configuration type 1 for base access [ 0.220013] Setting up standard PCI resources [ 0.224014] ACPI: EC: Look up EC in DSDT [ 0.231773] ACPI: Interpreter enabled [ 0.231843] ACPI: (supports S0 S1 S4 S5) [ 0.232014] ACPI: Using IOAPIC for interrupt routing [ 0.242563] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.242744] pci 0000:00:00.0: nForce2 C1 Halt Disconnect fixup [ 0.243842] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.244143] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] [ 0.244575] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT] [ 0.298490] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.299367] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 0.300153] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 0.300922] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 0.301689] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.302556] ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 0.303327] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 0.304106] ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 0.304873] ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.305739] ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.306605] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.307471] ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 0.308247] ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 0.309016] ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.309882] ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.310747] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.311593] ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled. [ 0.311980] ACPI: PCI Interrupt Link [APC2] (IRQs *17) [ 0.312329] ACPI: PCI Interrupt Link [APC3] (IRQs *18) [ 0.312671] ACPI: PCI Interrupt Link [APC4] (IRQs *19) [ 0.313014] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled. [ 0.313475] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0 [ 0.314013] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0 [ 0.314550] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0 [ 0.315087] ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled. [ 0.315667] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled. [ 0.316254] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled. [ 0.316771] ACPI: PCI Interrupt Link [APCS] (IRQs *23) [ 0.317179] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0 [ 0.317715] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled. [ 0.318296] ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled. [ 0.318880] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled. [ 0.319455] Linux Plug and Play Support v0.97 (c) Adam Belay [ 0.319566] pnp: PnP ACPI init [ 0.319640] ACPI: bus type pnp registered [ 0.327031] pnp: PnP ACPI: found 17 devices [ 0.327102] ACPI: ACPI bus type pnp unregistered [ 0.327170] PnPBIOS: Disabled by ACPI PNP [ 0.327585] PCI: Using ACPI for IRQ routing [ 0.327943] ACPI: RTC can wake from S4 [ 0.328062] system 00:00: ioport range 0x4000-0x407f has been reserved [ 0.328131] system 00:00: ioport range 0x4080-0x40ff has been reserved [ 0.328199] system 00:00: ioport range 0x4400-0x447f has been reserved [ 0.328268] system 00:00: ioport range 0x4480-0x44ff has been reserved [ 0.328336] system 00:00: ioport range 0x4200-0x427f has been reserved [ 0.328404] system 00:00: ioport range 0x4280-0x42ff has been reserved [ 0.328479] system 00:01: ioport range 0x5000-0x503f has been reserved [ 0.328558] system 00:02: iomem range 0xcf400-0xcffff has been reserved [ 0.328627] system 00:02: iomem range 0xf0000-0xf7fff could not be reserved [ 0.328695] system 00:02: iomem range 0xf8000-0xfbfff could not be reserved [ 0.328764] system 00:02: iomem range 0xfc000-0xfffff could not be reserved [ 0.328833] system 00:02: iomem range 0x3fff0000-0x3fffffff could not be reserved [ 0.328916] system 00:02: iomem range 0xffff0000-0xffffffff could not be reserved [ 0.329000] system 00:02: iomem range 0x0-0x9ffff could not be reserved [ 0.329068] system 00:02: iomem range 0x100000-0x3ffeffff could not be reserved [ 0.329151] system 00:02: iomem range 0xfec00000-0xfec00fff could not be reserved [ 0.329235] system 00:02: iomem range 0xfee00000-0xfee00fff could not be reserved [ 0.329324] system 00:04: ioport range 0xb78-0xb7b has been reserved [ 0.329392] system 00:04: ioport range 0xf78-0xf7b has been reserved [ 0.329460] system 00:04: ioport range 0xa78-0xa7b has been reserved [ 0.329528] system 00:04: ioport range 0xe78-0xe7b has been reserved [ 0.329595] system 00:04: ioport range 0xbbc-0xbbf has been reserved [ 0.329663] system 00:04: ioport range 0xfbc-0xfbf has been reserved [ 0.329731] system 00:04: ioport range 0x4d0-0x4d1 has been reserved [ 0.329799] system 00:04: ioport range 0x294-0x297 has been reserved [ 0.329866] system 00:04: ioport range 0x4e0-0x4e7 has been reserved [ 0.361520] PCI: Bridge: 0000:00:08.0 [ 0.361585] IO window: d000-dfff [ 0.361651] MEM window: 0xea000000-0xebffffff [ 0.361718] PREFETCH window: 0x0000000050000000-0x00000000500fffff [ 0.361790] PCI: Bridge: 0000:00:1e.0 [ 0.361852] IO window: disabled. [ 0.361917] MEM window: 0xe8000000-0xe9ffffff [ 0.361983] PREFETCH window: 0x00000000d8000000-0x00000000e7ffffff [ 0.362060] PCI: Setting latency timer of device 0000:00:08.0 to 64 [ 0.362089] NET: Registered protocol family 2 [ 0.362258] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.362730] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.364569] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.365486] TCP: Hash tables configured (established 131072 bind 65536) [ 0.365559] TCP reno registered [ 0.365771] NET: Registered protocol family 1 [ 0.365986] checking if image is initramfs... it is [ 0.575658] Freeing initrd memory: 2449k freed [ 0.576632] audit: initializing netlink socket (disabled) [ 0.576715] type=2000 audit(1227036948.576:1): initialized [ 0.576953] highmem bounce pool size: 64 pages [ 0.577021] Total HugeTLB memory allocated, 0 [ 0.577158] VFS: Disk quotas dquot_6.5.1 [ 0.577256] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.577368] msgmni has been set to 1767 [ 0.577552] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.577638] io scheduler noop registered [ 0.577701] io scheduler anticipatory registered [ 0.577766] io scheduler deadline registered [ 0.577838] io scheduler cfq registered (default) [ 0.578072] pci 0000:02:00.0: Boot video device [ 0.578500] isapnp: Scanning for PnP cards... [ 0.864023] Switched to high resolution mode on CPU 0 [ 0.933176] isapnp: No Plug & Play device found [ 0.936595] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 0.936843] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.937050] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 0.937566] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.937829] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 0.939900] brd: module loaded [ 0.940529] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 0.942926] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.942997] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.943241] mice: PS/2 mouse device common for all mice [ 0.943474] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0 [ 0.943563] rtc0: alarms up to one year, y3k [ 0.943673] cpuidle: using governor ladder [ 0.943738] cpuidle: using governor menu [ 0.943805] No iBFT detected. [ 0.944418] TCP cubic registered [ 0.944483] NET: Registered protocol family 17 [ 0.944554] Using IPI No-Shortcut mode [ 0.944771] registered taskstats version 1 [ 0.945022] rtc_cmos 00:06: setting system clock to 2008-11-18 19:35:49 UTC (1227036949) [ 0.945407] Freeing unused kernel memory: 244k freed [ 0.970630] input: AT Translated Set 2 keyboard as /class/input/input0 [ 0.991531] Uniform Multi-Platform E-IDE driver [ 0.991622] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 0.992633] NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller [ 0.992708] NFORCE2: IDE controller (0x10de:0x0065 rev 0xa2) at PCI slot 0000:00:09.0 [ 0.992822] NFORCE2: not 100% native mode: will probe irqs later [ 0.992892] NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround. [ 0.992974] NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround. [ 0.993067] ide0: BM-DMA at 0xf000-0xf007 [ 0.993139] ide1: BM-DMA at 0xf008-0xf00f [ 0.993207] Probing IDE interface ide0... [ 1.280134] hda: WDC WD1200JB-00REA0, ATA DISK drive [ 1.952075] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4 [ 1.952147] hda: UDMA/100 mode selected [ 1.952300] Probing IDE interface ide1... [ 2.688133] hdc: PIONEER DVD-RW DVR-109, ATAPI CD/DVD-ROM drive [ 3.360064] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4 [ 3.360169] hdc: UDMA/66 mode selected [ 3.360359] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 3.361985] ide1 at 0x170-0x177,0x376 on irq 15 [ 3.364045] No dock devices found. [ 3.374912] SCSI subsystem initialized [ 3.384381] libata version 3.00 loaded. [ 3.392181] hda: max request size: 512KiB [ 3.404605] hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63 [ 3.404605] hda: cache flushes supported [ 3.404605] hda: hda1 hda2 [ 3.447076] ACPI: PNP0C0B:00 is registered as cooling_device0 [ 3.447169] ACPI: Fan [FAN] (on) [ 3.453701] ACPI: ACPI0007:00 is registered as cooling_device1 [ 3.455999] ACPI: LNXTHERM:01 is registered as thermal_zone0 [ 3.456175] ACPI: Thermal Zone [THRM] (22 C) [ 4.082682] hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache [ 4.083014] Uniform CD-ROM driver Revision: 3.20 [ 4.317599] device-mapper: uevent: version 1.0.3 [ 4.319463] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: [EMAIL PROTECTED] [ 7.389524] PM: Starting manual resume from disk [ 7.455645] kjournald starting. Commit interval 5 seconds [ 7.455731] EXT3-fs: mounted filesystem with ordered data mode. [ 8.480914] udevd version 125 started [ 9.667976] Linux agpgart interface v0.103 [ 9.702998] agpgart: Detected NVIDIA nForce2 chipset [ 9.712261] agpgart: AGP aperture is 128M @ 0xd0000000 [ 10.044152] usbcore: registered new interface driver usbfs [ 10.044261] usbcore: registered new interface driver hub [ 10.044363] usbcore: registered new device driver usb [ 10.077061] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 10.077511] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22 [ 10.077590] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, high) -> IRQ 22 [ 10.077774] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 10.077779] ohci_hcd 0000:00:02.0: OHCI Host Controller [ 10.078082] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 [ 10.078190] ohci_hcd 0000:00:02.0: irq 22, io mem 0xec002000 [ 10.121445] input: Power Button (FF) as /class/input/input1 [ 10.136013] usb usb1: configuration #1 chosen from 1 choice [ 10.136123] hub 1-0:1.0: USB hub found [ 10.136201] hub 1-0:1.0: 3 ports detected [ 10.149694] ACPI: Power Button (FF) [PWRF] [ 10.149860] input: Power Button (CM) as /class/input/input2 [ 10.182431] ACPI: Power Button (CM) [PWRB] [ 10.240177] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 10.240253] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.240337] usb usb1: Product: OHCI Host Controller [ 10.240402] usb usb1: Manufacturer: Linux 2.6.26-1-686 ohci_hcd [ 10.240468] usb usb1: SerialNumber: 0000:00:02.0 [ 10.240970] ACPI: PCI Interrupt Link [APCG] enabled at IRQ 21 [ 10.241043] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 21 (level, high) -> IRQ 21 [ 10.241231] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 10.241236] ohci_hcd 0000:00:02.1: OHCI Host Controller [ 10.241337] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 [ 10.241442] ohci_hcd 0000:00:02.1: irq 21, io mem 0xec003000 [ 10.298155] usb usb2: configuration #1 chosen from 1 choice [ 10.298264] hub 2-0:1.0: USB hub found [ 10.298341] hub 2-0:1.0: 3 ports detected [ 10.400165] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 10.400241] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.400324] usb usb2: Product: OHCI Host Controller [ 10.400389] usb usb2: Manufacturer: Linux 2.6.26-1-686 ohci_hcd [ 10.400455] usb usb2: SerialNumber: 0000:00:02.1 [ 10.400671] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x5000 [ 10.400758] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x5040 [ 10.484578] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20 [ 10.484658] ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 20 (level, high) -> IRQ 20 [ 10.484843] PCI: Setting latency timer of device 0000:00:02.2 to 64 [ 10.484848] ehci_hcd 0000:00:02.2: EHCI Host Controller [ 10.484964] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3 [ 10.485084] ehci_hcd 0000:00:02.2: debug port 1 [ 10.485152] PCI: cache line size of 64 is not supported by device 0000:00:02.2 [ 10.485169] ehci_hcd 0000:00:02.2: irq 20, io mem 0xec004000 [ 10.499312] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 10.499518] usb usb3: configuration #1 chosen from 1 choice [ 10.499620] hub 3-0:1.0: USB hub found [ 10.499695] hub 3-0:1.0: 6 ports detected [ 10.600181] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 10.600257] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.601375] usb usb3: Product: EHCI Host Controller [ 10.601440] usb usb3: Manufacturer: Linux 2.6.26-1-686 ehci_hcd [ 10.601506] usb usb3: SerialNumber: 0000:00:02.2 [ 11.158613] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 11.169839] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 11.205873] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61. [ 11.206390] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22 [ 11.206460] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCH] -> GSI 22 (level, high) -> IRQ 22 [ 11.206634] PCI: Setting latency timer of device 0000:00:04.0 to 64 [ 11.386472] input: PC Speaker as /class/input/input3 [ 11.692499] FDC 0 is a post-1991 82077 [ 11.724735] forcedeth 0000:00:04.0: ifname eth0, PHY OUI 0x732 @ 1, addr 5e:00:be:f1:be:60 [ 11.724829] forcedeth 0000:00:04.0: timirq lnktim desc-v1 [ 11.853213] ath_hal: module license 'Proprietary' taints kernel. [ 11.854597] AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425, RF2417) [ 11.946045] gameport: EMU10K1 is pci0000:01:07.1/gameport0, io 0xd400, speed 59659kHz [ 11.953469] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17 [ 11.953549] ACPI: PCI Interrupt 0000:01:0d.0[A] -> Link [APC2] -> GSI 17 (level, high) -> IRQ 17 [ 12.005568] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17] MMIO=[eb011000-eb0117ff] Max Packet=[2048] IR/IT contexts=[8/8] [ 12.080056] 8139too Fast Ethernet driver 0.9.28 [ 12.097891] input: ImPS/2 Logitech Wheel Mouse as /class/input/input4 [ 12.177934] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 [ 12.178015] ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC3] -> GSI 18 (level, high) -> IRQ 18 [ 12.758788] MadWifi: ath_attach: Switching rfkill capability off. [ 12.781087] parport_pc 00:0c: reported by Plug and Play ACPI [ 12.781221] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] [ 12.831735] wifi0: Atheros AR2414 chip found (MAC 7.9, PHY 2112A 4.5, Radio 5.6) [ 12.853687] ath_pci: wifi0: Atheros 5212: mem=0xeb000000, irq=18 [ 12.854091] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19 [ 12.854164] ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC4] -> GSI 19 (level, high) -> IRQ 19 [ 12.901593] gameport: NS558 PnP Gameport is pnp00:0f/gameport0, io 0x200, speed 59659kHz [ 12.903218] ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC4] -> GSI 19 (level, high) -> IRQ 19 [ 12.904406] eth1: RealTek RTL8139 at 0xd800, 00:04:61:56:43:ea, IRQ 19 [ 12.904475] eth1: Identified 8139 chip type 'RTL-8101' [ 12.953936] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) [ 13.448221] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00046100000609e8] [ 14.471004] EXT3 FS on dm-0, internal journal [ 15.276152] loop: module loaded [ 16.608499] kjournald starting. Commit interval 5 seconds [ 16.608726] EXT3 FS on hda1, internal journal [ 16.608837] EXT3-fs: mounted filesystem with ordered data mode. [ 16.625881] kjournald starting. Commit interval 5 seconds [ 16.625881] EXT3 FS on dm-1, internal journal [ 16.628079] EXT3-fs: mounted filesystem with ordered data mode. [ 16.687230] kjournald starting. Commit interval 5 seconds [ 16.687494] EXT3 FS on dm-2, internal journal [ 16.687604] EXT3-fs: mounted filesystem with ordered data mode. [ 16.717107] kjournald starting. Commit interval 5 seconds [ 16.717107] EXT3 FS on dm-3, internal journal [ 16.717107] EXT3-fs: mounted filesystem with ordered data mode. [ 16.731054] kjournald starting. Commit interval 5 seconds [ 16.731054] EXT3 FS on dm-4, internal journal [ 16.731054] EXT3-fs: mounted filesystem with ordered data mode. [ 17.111151] Adding 2097144k swap on /dev/mapper/VolGroup00-LogVol01. Priority:-1 extents:1 across:2097144k [ 20.397028] lp0: using parport0 (interrupt-driven). [ 20.421554] ppdev: user-space parallel port driver [ 21.046965] NET: Registered protocol family 10 [ 21.047692] lo: Disabled Privacy Extensions [ 22.923212] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use) [ 24.351180] eth1: link up, 100Mbps, full-duplex, lpa 0x41E1 [ 24.579302] eth0: no link during initialization. [ 24.580208] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 28.001226] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC4] -> GSI 19 (level, high) -> IRQ 19 [ 28.001750] NVRM: loading NVIDIA Linux x86 Kernel Module 96.43.07 Wed Jul 2 12:17:43 PDT 2008 [ 28.079374] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. [ 28.079403] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode [ 28.079478] agpgart: Putting AGP V2 device at 0000:02:00.0 into 4x mode [ 46.016025] eth1: no IPv6 routers present It would be very much appreciated is this could be looked at. Thanks! -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
