Your message dated Sun, 4 Oct 2009 21:18:01 +0200
with message-id <[email protected]>
and subject line Re: ieee1394: sbp2: unit is reset on heavy load
has caused the Debian Bug report #501916,
regarding ieee1394: sbp2: unit is reset on heavy load
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact [email protected]
immediately.)
--
501916: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=501916
Debian Bug Tracking System
Contact [email protected] with problems
--- Begin Message ---
Package: linux-image-2.6.26-1-486
Version: 2.6.26-5
Severity: grave
Justification: causes non-serious data loss
-- Package-specific info:
** Version:
Linux version 2.6.26-1-486 (Debian 2.6.26-5) ([email protected]) (gcc version
4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 Wed Sep 10 16:00:21 UTC 2008
** Command line:
root=/dev/sda3 ro keykbd=fr vga=792
** Not tainted
** Kernel log:
[ 12.407235] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 12.407252] sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled,
doesn't support DPO or FUA
[ 12.570927] ata4.00: configured for UDMA/133
[ 12.576730] ata4: EH complete
[ 12.582507] sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
[ 12.590497] sd 3:0:0:0: [sdd] Write Protect is off
[ 12.596237] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 12.596254] sd 3:0:0:0: [sdd] Write cache: disabled, read cache: enabled,
doesn't support DPO or FUA
[ 12.797716] Adding 1004052k swap on /dev/sda2. Priority:-1 extents:1
across:1004052k
[ 13.088448] EXT3 FS on sda3, internal journal
[ 13.209570] loop: module loaded
[ 13.270043] it87: Found IT8716F chip at 0x290, revision 0
[ 13.277010] it87: in3 is VCC (+5V)
[ 13.282491] it87: in7 is VCCH (+5V Stand-By)
[ 14.444003] kjournald starting. Commit interval 5 seconds
[ 14.454916] EXT3 FS on sda6, internal journal
[ 14.462773] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.478245] kjournald starting. Commit interval 5 seconds
[ 14.484469] EXT3 FS on sda5, internal journal
[ 14.490315] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.563542] kjournald starting. Commit interval 5 seconds
[ 14.663234] EXT3 FS on md0, internal journal
[ 14.669141] EXT3-fs: mounted filesystem with ordered data mode.
[ 16.057447] NET: Registered protocol family 10
[ 16.063666] lo: Disabled Privacy Extensions
[ 18.484009] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3500+
processors (1 cpu cores) (version 2.20.00)
[ 18.484009] powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x8
[ 18.484009] powernow-k8: 1 : fid 0xc (2000 MHz), vid 0xa
[ 18.484009] powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xc
[ 18.484009] powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12
[ 23.026640] lp0: using parport0 (interrupt-driven).
[ 23.048365] ppdev: user-space parallel port driver
[ 23.352223] Marking TSC unstable due to: cpufreq changes.
[ 24.000016] Clocksource tsc unstable (delta = -90895943 ns)
[ 25.112236] warning: `avahi-daemon' uses 32-bit capabilities (legacy support
in use)
[ 26.644012] eth1: no IPv6 routers present
[ 46.928047] ieee1394: Error parsing configrom for node 0-00:1023
[ 46.940549] ieee1394: Node changed: 0-00:1023 -> 0-01:1023
[ 53.016063] ieee1394: Node added: ID:BUS[0-00:1023] GUID[0050770e00071002]
[ 53.020648] scsi4 : SBP-2 IEEE-1394
[ 54.036724] ieee1394: sbp2: Logged into SBP-2 device
[ 54.049331] ieee1394: sbp2: Node 0-00:1023: Max speed [S400] - Max payload
[2048]
[ 54.062642] scsi 4:0:0:0: Direct-Access-RBC MAXTOR S TM3250820A
PQ: 0 ANSI: 4
[ 54.079725] sd 4:0:0:0: [sde] 488397168 512-byte hardware sectors (250059 MB)
[ 54.089444] sd 4:0:0:0: [sde] Write Protect is off
[ 54.102453] sd 4:0:0:0: [sde] Mode Sense: 11 00 00 00
[ 54.103055] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 54.132005] sd 4:0:0:0: [sde] 488397168 512-byte hardware sectors (250059 MB)
[ 54.144965] sd 4:0:0:0: [sde] Write Protect is off
[ 54.158434] sd 4:0:0:0: [sde] Mode Sense: 11 00 00 00
[ 54.174581] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 54.186107] sde: sde1
[ 54.221991] sd 4:0:0:0: [sde] Attached SCSI disk
[ 197.672775] kjournald starting. Commit interval 5 seconds
[ 197.687788] EXT3 FS on sde1, internal journal
[ 197.703033] EXT3-fs: mounted filesystem with ordered data mode.
[ 383.808019] kjournald starting. Commit interval 5 seconds
[ 383.855431] EXT3 FS on sde1, internal journal
[ 383.870699] EXT3-fs: mounted filesystem with ordered data mode.
[ 729.632025] ieee1394: sbp2: aborting sbp2 command
[ 729.645622] sd 4:0:0:0: [sde] CDB: Mode Sense(6): 1a 00 1c 00 ff 00
[ 739.660021] ieee1394: sbp2: aborting sbp2 command
[ 739.673694] sd 4:0:0:0: [sde] CDB: Test Unit Ready: 00 00 00 00 00 00
[ 739.687997] ieee1394: sbp2: reset requested
[ 739.703666] ieee1394: sbp2: generating sbp2 fetch agent reset
[ 749.716023] ieee1394: sbp2: aborting sbp2 command
[ 749.729826] sd 4:0:0:0: [sde] CDB: Test Unit Ready: 00 00 00 00 00 00
[ 749.747732] sd 4:0:0:0: Device offlined - not ready after error recovery
** Loaded modules:
Module Size Used by
usb_storage 75712 1
ppdev 6404 0
lp 7972 0
video 16272 0
output 2816 1 video
ac 4228 0
battery 10116 0
powernow_k8 11020 0
cpufreq_conservative 5664 0
cpufreq_userspace 2968 1
cpufreq_ondemand 6036 0
cpufreq_powersave 1792 0
cpufreq_stats 3076 0
freq_table 4100 3 powernow_k8,cpufreq_ondemand,cpufreq_stats
ipv6 225172 26
ext2 52616 1
it87 17808 0
hwmon_vid 2560 1 it87
sbp2 18700 0
loop 12428 0
dm_mod 45384 0
parport_pc 22436 1
parport 30408 3 ppdev,lp,parport_pc
snd_hda_intel 323992 0
snd_pcm_oss 32544 0
snd_mixer_oss 12288 1 snd_pcm_oss
pcspkr 2304 0
snd_pcm 60808 2 snd_hda_intel,snd_pcm_oss
k8temp 4096 0
snd_seq_dummy 2692 0
snd_seq_oss 24832 0
snd_seq_midi 5664 0
snd_rawmidi 18720 1 snd_seq_midi
snd_seq_midi_event 6528 2 snd_seq_oss,snd_seq_midi
snd_seq 40784 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 17668 2 snd_pcm,snd_seq
snd_seq_device 6412 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 45092 9
snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 6112 1 snd
snd_page_alloc 7816 2 snd_hda_intel,snd_pcm
button 6032 0
i2c_nforce2 5504 0
i2c_core 19728 1 i2c_nforce2
evdev 7808 3
ext3 103432 5
jbd 35092 1 ext3
mbcache 6656 2 ext2,ext3
raid456 115216 1
md_mod 65940 2 raid456
async_xor 3456 1 raid456
async_memcpy 2176 1 raid456
async_tx 5960 3 raid456,async_xor,async_memcpy
xor 14728 2 raid456,async_xor
sd_mod 22032 14
ata_generic 4612 0
sata_nv 19208 8
libata 141088 2 ata_generic,sata_nv
scsi_mod 129804 4 usb_storage,sbp2,sd_mod,libata
dock 8076 1 libata
ide_pci_generic 3844 0 [permanent]
amd74xx 7688 0 [permanent]
forcedeth 44816 0
ide_core 91444 2 ide_pci_generic,amd74xx
ohci1394 25136 0
ieee1394 75832 2 sbp2,ohci1394
ohci_hcd 18436 0
ehci_hcd 28300 0
usbcore 117616 4 usb_storage,ohci_hcd,ehci_hcd
thermal 15132 0
processor 28080 2 powernow_k8,thermal
fan 4100 0
thermal_sys 10784 4 video,thermal,processor,fan
** PCI devices:
00:00.0 RAM memory [0500]: nVidia Corporation MCP61 Memory Controller
[10de:03ea] (rev a1)
Subsystem: Giga-byte Technology Device [1458:5001]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 ISA bridge [0601]: nVidia Corporation MCP61 LPC Bridge [10de:03e0] (rev
a2)
Subsystem: Giga-byte Technology Device [1458:0c11]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.1 SMBus [0c05]: nVidia Corporation MCP61 SMBus [10de:03eb] (rev a2)
Subsystem: Giga-byte Technology Device [1458:0c11]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at b000 [size=64]
Region 4: I/O ports at 1c00 [size=64]
Region 5: I/O ports at b800 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:01.2 RAM memory [0500]: nVidia Corporation MCP61 Memory Controller
[10de:03f5] (rev a2)
Subsystem: Giga-byte Technology Device [1458:0c11]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:02.0 USB Controller [0c03]: nVidia Corporation MCP61 USB Controller
[10de:03f1] (rev a2) (prog-if 10)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f5105000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:02.1 USB Controller [0c03]: nVidia Corporation MCP61 USB Controller
[10de:03f2] (rev a2) (prog-if 20)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 23
Region 0: Memory at f5106000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:04.0 PCI bridge [0604]: nVidia Corporation MCP61 PCI bridge [10de:03f3] (rev
a1) (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: f5000000-f50fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:05.0 Audio device [0403]: nVidia Corporation MCP61 High Definition Audio
[10de:03f0] (rev a2)
Subsystem: Giga-byte Technology Device [1458:a002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin B routed to IRQ 22
Region 0: Memory at f5100000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:06.0 IDE interface [0101]: nVidia Corporation MCP61 IDE [10de:03ec] (rev a2)
(prog-if 8a [Master SecP PriP])
Subsystem: Giga-byte Technology Device [1458:5002]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: <access denied>
Kernel driver in use: AMD_IDE
Kernel modules: amd74xx
00:07.0 Bridge [0680]: nVidia Corporation MCP61 Ethernet [10de:03ef] (rev a2)
Subsystem: Giga-byte Technology Device [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 223
Region 0: Memory at f5107000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at bc00 [size=8]
Capabilities: <access denied>
Kernel driver in use: forcedeth
Kernel modules: forcedeth
00:08.0 IDE interface [0101]: nVidia Corporation MCP61 SATA Controller
[10de:03f6] (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: Giga-byte Technology Device [1458:b002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at d000 [size=16]
Region 5: Memory at f5108000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
Kernel modules: sata_nv
00:08.1 IDE interface [0101]: nVidia Corporation MCP61 SATA Controller
[10de:03f6] (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: Giga-byte Technology Device [1458:b002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 23
Region 0: I/O ports at 09e0 [size=8]
Region 1: I/O ports at 0be0 [size=4]
Region 2: I/O ports at 0960 [size=8]
Region 3: I/O ports at 0b60 [size=4]
Region 4: I/O ports at e400 [size=16]
Region 5: Memory at f5104000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
Kernel modules: sata_nv
00:0d.0 VGA compatible controller [0300]: nVidia Corporation GeForce 6100
nForce 430 [10de:03d0] (rev a2)
Subsystem: Giga-byte Technology Device [1458:d000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f2000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at f3000000 (64-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at 50000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: nvidiafb
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k8temp
Kernel modules: k8temp
01:0e.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23
IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10)
Subsystem: Giga-byte Technology Device [1458:1000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f5004000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at f5000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: ohci1394
Kernel modules: ohci1394
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-1-486
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-486 depends on:
ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92j tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.26-1-486 recommends no packages.
Versions of packages linux-image-2.6.26-1-486 suggests:
ii grub 0.97-47 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-1-486/preinst/lilo-has-ramdisk:
linux-image-2.6.26-1-486/preinst/overwriting-modules-2.6.26-1-486: true
linux-image-2.6.26-1-486/preinst/abort-overwrite-2.6.26-1-486:
linux-image-2.6.26-1-486/postinst/old-system-map-link-2.6.26-1-486: true
linux-image-2.6.26-1-486/prerm/removing-running-kernel-2.6.26-1-486: true
linux-image-2.6.26-1-486/preinst/failed-to-move-modules-2.6.26-1-486:
linux-image-2.6.26-1-486/postinst/old-initrd-link-2.6.26-1-486: true
linux-image-2.6.26-1-486/preinst/abort-install-2.6.26-1-486:
linux-image-2.6.26-1-486/postinst/create-kimage-link-2.6.26-1-486: true
linux-image-2.6.26-1-486/postinst/bootloader-test-error-2.6.26-1-486:
linux-image-2.6.26-1-486/preinst/bootloader-initrd-2.6.26-1-486: true
linux-image-2.6.26-1-486/preinst/elilo-initrd-2.6.26-1-486: true
linux-image-2.6.26-1-486/preinst/initrd-2.6.26-1-486:
linux-image-2.6.26-1-486/postinst/bootloader-error-2.6.26-1-486:
linux-image-2.6.26-1-486/preinst/lilo-initrd-2.6.26-1-486: true
linux-image-2.6.26-1-486/postinst/depmod-error-2.6.26-1-486: false
linux-image-2.6.26-1-486/postinst/kimage-is-a-directory:
linux-image-2.6.26-1-486/prerm/would-invalidate-boot-loader-2.6.26-1-486: true
linux-image-2.6.26-1-486/postinst/old-dir-initrd-link-2.6.26-1-486: true
linux-image-2.6.26-1-486/postinst/depmod-error-initrd-2.6.26-1-486: false
--- End Message ---
--- Begin Message ---
Version: 2.6.30-1
On Wed, Sep 30, 2009 at 07:43:16PM +0200, Franck wrote:
> Hi,
>
> wth the last update of dmraid, I was able to start the last kernel, and I
> have not seen problems anymore for the moment.
>
> I'll contact you back if there is a problem again.
Ok, marking as closed for now. Please get back to us if the problem
reappears.
Cheers,
Moritz
--- End Message ---
